Din Iso Comparison Sheet

DIN / ISO COMPARISON CHART Issued By: Metric Products Group

Eff. Date: 08/29/12

Revision : 00

Page 1 of 3

Subject: DIN / ISO COMPARISON CHART This chart shows product descriptions along with their DIN standard and the corresponding ISO standard that has replaced the now obsolete DIN. (If an item shows “NO REPLACEMENT” that DIN standard has been withdrawn and has not been replaced by an ISO standard.) DESCRIPTION TAPER PIN - UNHARDENED DOWEL PIN - UNHARDENED SLOTTED CHEESE HEAD MACHINE SCREW SLOTTED PAN HEAD MACHINE SCREW TAB WASHERS WITH LONG TAB COTTER (SPLIT) PINS FLAT WASHER - UNCHAMFERED (GRADE A) FLAT WASHER CHAMFERED (GRADE A) FLAT WASHER (GRADE C) SPLIT LOCK WASHER WITH TANG SPLIT LOCK WASHER WITH SQUARE ENDS SPLIT LOCK WASHER - CURVED SPLIT LOCK WASHER - WAVY SPLIT LOCK WASHER - CURVED (SPLIT / NAPPED) SPRING WASHER - CURVED (UNSPLIT) SPRING WASHER - WAVY (UNSPLIT) WING NUTS - EDGED WINGS WING NUTS - ROUNDED WINGS WING SCREWS - ROUNDED WINGS WING SCREWS - EDGE WINGS SLOTTED SET SCREW WITH FULL DOG POINT SLOTTED SET SCREW - PARTIALLY THREADED EXTERNAL TAB WASHER PLAIN WASHERS - SMALL SERIES, PRODUCTS GRADE A SLOTTED SET SCREW WITH CUP POINT HEX THIN (JAM) NUTS - CHAMFERED GRADES A&B HEX THIN (JAM) NUTS - UNCHAMFERED GRADE B HEX THIN (JAM) NUTS - CHAMFERED WITH METRIC FINE PITCH THREAD GRADES A&B SWING EYE BOLT INTERNAL TAB WASHERS FOR SLOTTED ROUND NUTS TAB WASHERS WITH LONG & SHORT TABS RETAINING RING (CIRCLIPS) FOR SHAFTS; NORMAL AND HEAVY TYPE RETAINING RING (CIRCLIPS) FOR BORES; NORMAL AND HEAVY TYPE NUTS FOR T-SLOTS SLOTTED SET SCREW WITH FLAT POINT SQUARE NUTS - GRADE C HEX HEAD SET SCREW WITH REDUCED WAF AND DOG POINT EYE BOLTS - SHOULDER PATTERN EYE NUTS CARRIAGE BOLTS WITH SQUARE NECK DOUBLE END STUD (TAP END ~ 2d) HEX SOCKET PIPE PLUGS - METRIC, BSPT, NPT HEX SOCKET SCREW PLUG - METRIC FINE, BSPP HEX HEAD PIPE PLUG

DIN STANDARD 1 7 84A 85A 93 94 125A 125B 126 127A 127B 128A 128B 128P 137A 137B 314 315 316 318 417 427 432 433 438 439 439 439 444 462 463 471 472 508 551 557 561 580 582 603 835 Fo 906 908 909

ISO STANDARD ISO 2339 ISO 2338 ISO 1207 ISO 1580 NO REPLACEMENT ISO 1234 ISO 7089 ISO 7090 ISO 7091 NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT CURRENT CURRENT CURRENT CURRENT ISO 7435 ISO 2342 NO REPLACEMENT ISO 7092 ISO 7436 ISO 4035 ISO 4036 ISO 8765 CURRENT CURRENT NO REPLACEMENT CURRENT CURRENT CURRENT ISO 4766 CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT

DIN / ISO COMPARISON CHART Issued By: Metric Products Group

Eff. Date: 08/29/12

Revision : 00

DESCRIPTION HEAVY-DUTY HEX HEAD SCREW PLUG HEX KEY - TO SUIT SOCKET SCREWS HEX SOCKET CAP SCREWS HEX SOCKET SET SCREWS - FLAT POINT HEX SOCKET SET SCREWS - CONE POINT HEX SOCKET SET SCREWS - DOG POINT HEX SOCKET SET SCREWS - CUP POINT SQUARE WELD NUT HEX WELD NUT HEX HEAD BOLT - PARTIAL THREAD HEX HEAD BOLT - FULL THREAD HEX NUTS HEX SLOTTED AND CASTLE NUTS HEX JAM NUT HEX THIN SLOTTED AND CASTLE NUT STUD (METAL END ~1d) STUD (METAL END ~1.25d) HEX HEAD BOLT WITH METRIC FINE THREAD - PARTIAL THREAD HEX HEAD BOLT WITH METRIC FINE THREAD - FULL THREAD SLOTTED FLAT COUNTERSUNK HEAD MACHINE SCREW SLOTTED OVAL COUNTERSUNK HEAD MACHINE SCREW PHILLIPS FLAT HEAD COUNTERSUNK MACHINE SCREW - PROPERTY CLASS 4.6 PHILLIPS FLAT HEAD COUNTERSUNK MACHINE SCREW - PROPERTY CLASS 8.8 PHILLIPS OVAL HEAD MACHINE SCREW THREADED ROD PREVAILING TORQUE HEX NUT WITH NON-METALLIC INSERT (PROPERTY CLASSES 5, 8, 10) PREVAILING TORQUE HEX NUT WITH ALL METAL INSERT (PROPERTY CLASSES 5, 8, 10) PREVAILAING TORQUE HEX NUT WITH NON-METALLIC INSERT - THIN TYPE PREVAILING TORQUE HEXAGON DOMED CAP NUT WITH NON-METALLIC INSERT SHIM WASHER (TO SUIT RETAINING RINGS DIN 471 AND 472) SLOTTED SPRNG STYPE STRAIGHT PIN HEX DOMED CAP NUTS (ACORN NUTS) DOWEL PIN - HARDENED STEEL HEXAGON LONG NUT - COUPLING NUT LOCK WASHER - TOOTHED (EXTERNAL TYPE) LOCK WASHER - TOOTHED (INTERNAL TYPE) LOCK WASHER - TOOTHED (INTERNAL TYPE) LOCK WASHER - SERRATED (EXTERNAL TYPE - 90° COUNTERSUNK) LOCK WASHER - SERRATED (EXTERNAL TYPE) LOCK WASHER - SERRATED (EXTERNAL / INTERNAL TYPE) LOCK WASHER - SERRATED (INTERNAL TYPE) LOCK WASHER - SERRATED (INTERNAL TYPE) LOCK WASHER - SERRATED (EXTERNAL TYPE - 90° COUNTERSUNK) WOODRUFF KEY HEX KEY WITH PILOT TO SUIT SOCKET SCREWS HEX SOCKET CAP SCREW WITH LOW HEAD AND PILOT RECESS HEX HIGH STRENGTH STRUCTURAL BOLT & NUT ASSEMBLIES HEX FLANGE BOLT - HEAVY SERIES HEX FLANGE NUT SPRING TYPE STRAIGHT PIN; COILED

DIN STANDARD 910 911 912 913 914 915 916 928 929 931 933 93 935 936 937 938 939 960 961 963 964 965 965 966 975 980 980 985 986 988 1481 1587 6325 6334 6797 A 6797 I 6797 J 6797 V 6798 A 6798 D 6798 I 6798 J 6798 V 6888 6911 6912 6914 / 6915 / 6916 6912 6923 7343

Page 2 of 3

ISO STANDARD CURRENT ISO 2936 ISO 4762 ISO 4026 ISO 4027 ISO 4028 ISO 4029 CURRENT CURRENT ISO 4014 ISO 4017 ISO 4032 CURRENT NO REPLACEMENT NO REPLACEMENT CURRENT CURRENT ISO 8765 ISO 8676 ISO 2009 ISO 2010 ISO 7046-1 ISO 7046-2 ISO 7047 NO REPLACEMENT ISO 7040 ISO 7042 ISO 10511 CURRENT CURRENT ISO 8752 CURRENT ISO 8734 CURRENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT NO REPLACEMENT CURRENT CURRENT CURRENT DIN EN 14399-4 DIN EN 1665 ISO 4161 ISO 8750

DIN / ISO COMPARISON CHART Issued By: Metric Products Group

Eff. Date: 08/29/12

Revision : 00

DESCRIPTION PLAIN WASHER - FOR BOLTS WITH HEAVY CLAMPING SLEEVES PHILLIPS PAN HEAD TRILOBULAR THREAD FORMING SCREW HEX HEAD WASHER FACE TRILOBULAR THREAD FORMING SCREW HEX HEAD TRILOBULAR THREAD FORMING SCREW PHILLIPS FLAT HEAD TRILOBULAR THREAD FORMING SCREW PHILLIPS OVAL HEAD SELF DRILLING / TAPPING SCREW HEX HEAD WASHER HEAD SELF DRILLING / TAPPING SCREW PHILLIPS PAN HEAD SELF DRILLING / TAPPING SCREW PHILLIPS FLAT COUNTERSUNK HEAD SELF DRILLING / TAPPING SCREW HEX HEAD THREAD CUTTING SCREW SLOTTED CHEESE HEAD THREAD SCREW HEX & SLOTTED HEAD THREAD CUTTING SCREW PHILLIPS PAN HEAD THREAD CUTTING SCREWS PHILLIPS FLAT COUNTERSUNK HEAD THREAD CUTTING SCREW PHILLIPS OVAL HEAD THREAD CUTTING SCREW SEALING RING (WASHER) - COPPER OR ALUMINUM HEX HEAD SCREW PLUG - LIGHT DUTY UNHARDENED TAPER PIN WITH EXTERNAL THREAD UNHARDENED TAPER PIN WITH INTERNAL THREAD DOWEL PIN WITH INTERNAL THREAD SPRING WASHERS - HIGH COLLAR TYPE FOR SOCKET HEAD / PAN HEAD SCREWS PHILLIPS / POZIDRIVE PAN HEAD SELF TAPPING SCREW PHILLIPS / POZIDRIVE PAN HEAD SLEF TAPPING SCREW WITH FLAT POINT PHILLIPS / POZIDRIVE FLAT COUNTERSUNK HEAD SELF TAPPING SCREW PHILLIPS / POZIDRIVE FLAT COUNTERSUNK HEAD SELF TAPPING SCREW WITH FLAT POINT PHILLIPS / POZIDRIVE OVAL COUNTERSUNK HEAD SELF TAPPING SCREW HEX SOCKET LOW HEAD CAP SCREW PHILLIPS PAN HEAD SELF TAPPING SCREW HEX SOCKET FLAT COUNTERSUNK HEAD SCREW LARGE OUTSIDE DIAMETER (FENDER) WASHER

DIN STANDARD 7349 7500 C 7500 D 7500 E 7500 M 7504 7504 K 7504 N 7504 P 7513 A 7513 B 7513 7516 A 7516 D 7516 E 7603 7604 7977 7978 A 7979 D 7980 7981 C 7981 F 7982 C 7982 F 7983 C 7984 7985 7991 9021

Page 3 of 3

ISO STANDARD CURRENT DIN 7500-1 DIN 7500-1 DIN 7500-1 DIN 7500-1 ISO 15483 ISO 15480 ISO 15481 ISO 15482 CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT ISO 8737 ISO 8736 ISO 8733 NO REPLACEMENT ISO 7049 ISO 7049 ISO 7050 ISO 7050 ISO 7051 CURRENT ISO 7045 ISO 10642 ISO 7093