Piping Handbook

PIPING HANDBOOK

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 1 OF 6

REV. 0

Purpose of Piping Handbook This piping handbook has been set-up as guidance for the piping department. The purpose of the piping handbook is that everybody works with the same basic information. A project handbook can be made out off this handbook together with client requirements. The following information is only for design purposes, item has to be confirmed by client, applicable department of KH engineering or replaced by client requirements; • • • • • • • • • •

Abbreviations to be used. Standard insulation thickness Reinforcing pad requirements Type of valves. Type of control valve Relief valves to be used Vessel saddles, legs, brackets Stairway arrangement. Cage ladder type. Type of hand railing.

Please send any modifications or additions to this piping handbook, in writing, to the piping focal point of your business unit.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 2 OF 6

REV. 0

INDEX DESIGN GUIDES Document no 30101-30-17D-001 30101-30-17D-100 30101-30-17D-101 30101-30-17D-102 30101-30-17D-103 30101-30-17D-104 30101-30-17D-105 30101-30-17D-106 30101-30-17D-107 30101-30-17D-108 30101-30-17D-109 30101-30-17D-110 30101-30-17D-111 30101-30-17D-112 30101-30-17D-113 30101-30-17D-114 30101-30-17D-115 30101-30-17D-116 30101-30-17D-117

Rev No of sh't 0 5 0 5 0 2 0 3 0 1 0 4 0 1 0 1 0 3 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 2 0 4

Description Front sheet and index Abbreviations Conversion from metric to imperial Conversion table for temperatures Conversion of pressure and stress to Newton Instructions for site visites Pressure classes according DIN 2401 Pressure – temperature table ANSI – DIN ASTM, DIN and ISO norms EN-standards Conversion table stainless steel standards Table for pipe capacity Table for velocity liquids and gasses. Table for branches per header Trigonometric functions Rule of the thump Test pressure Min. clearance for average man Standard insulation thickness

ANSI STANDARDS PIPE AND FITTINGS Document no 30101-30-17D-200 30101-30-17D-201 30101-30-17D-202 30101-30-17D-203 30101-30-17D-204 30101-30-17D-205 30101-30-17D-206 30101-30-17D-207 30101-30-17D-208 30101-30-17D-209

0 Rev.

01/2002 Date

Rev No of sh't 0 5 0 1 0 1 0 1 0 1 0 1 0 2 0 1 0 7 0 2

Description Dimensions and particulars of line pipe Minimum pipe spacing w/ANSI flanges Minimum pipe spacing for 450 take- off Built-up dimensions small bore fittings Small bore fittings and valves Dimensions reducing tee Dimensions for parts of elbow Dimensions of bends R=3D/R=5D Dimensions of ANSI flanges Assembly of RTJ weld neck flanges

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 3 OF 6

REV. 0

Document no 30101-30-17D-210 30101-30-17D-211 30101-30-17D-212 30101-30-17D-213 30101-30-17D-214 30101-30-17D-215 30101-30-17D-216 30101-30-17D-217 30101-30-17D-218

Rev No of sh't 0 1 0 2 0 1 0 1 0 1 0 1 0 1 0 1 0 1

Description Stub ends Built-up dimensions fittings and flanges Built-up dimensions fittings and RTJ flanges Built-up dimensions weldolets Built-up dimensions sockolets and threadolets Branch dimensions 150# and 300# WN flanges Reinforcing pad requirements Built-up dimensions for pad flanges UNC or ISO bolts for ANSI flanges

VALVES / STRAINERS/BLINDS Document no 30101-30-17D-230 30101-30-17D-231 30101-30-17D-232 30101-30-17D-233 30101-30-17D-234 30101-30-17D-235 30101-30-17D-236

Rev No of sh't 0 1 0 1 0 1 0 2 0 1 0 1 0 3

Description Flanged valves RF 150# up/to 300# Flanged valves RF 600# up/to 2500# Globe type control valves Camflex type control valves Relief valves up/to 1500# Temporary strainers Spectacle blinds

DIN STANDARDS PIPE AND FITTINGS Document no 30101-30-17D-300 30101-30-17D-301 30101-30-17D-302 30101-30-17D-303 30101-30-17D-304 30101-30-17D-305 30101-30-17D-306 30101-30-17D-307 30101-30-17D-308 30101-30-17D-309 30101-30-17D-310

0 Rev.

01/2002 Date

Rev No of sh't 0 1 0 1 0 1 0 1 0 1 0 1 0 3 0 1 0 1 0 8 0 1

Description Pipe DIN 2448 (seamless carbon steel) Pipe DIN 2458 (welded carbon steel) Pipe DIN 2462 (seamless stainless steel) Pipe DIN 2463 (welded stainless steel) Pressure Classes according DIN Minimum pipe spacing with DIN flanges Built-up dimensions fittings and flanges BW Tee DIN Dimensions of Parts of elbows- DIN Dimensions of DIN Flanges Bolts for DIN flanges

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 4 OF 6

REV. 0

VALVES Document no 30101-30-17D-320

Rev No of Description sh't 0 2 Flanged DIN valves up/to DN250

STRESS / SUPPORTING Document no 30101-30-17D-400 30101-30-17D-401 30101-30-17D-402 30101-30-17D-403 30101-30-17D-404 30101-30-17D-405

Rev No of sh't 0 2 0 2 0 4 0 3 0 1 0 2

Description Piping stress review criteria Allowable pipe span Coefficient of expansion Stress monogram and formulas Stoomwezen approval criteria Weights of valves, flanges and fittings

EQUIPMENT Document no 30101-30-17D-500 30101-30-17D-501 30101-30-17D-502 30101-30-17D-503 30101-30-17D-504 30101-30-17D-505 30101-30-17D-506 30101-30-17D-507 30101-30-17D-508

0 Rev.

01/2002 Date

Rev No of sh't 0 1 0 1 0 2 0 1 0 1 0 1 0 1 0 1 0 1

Description Typical arrangement horizontal vessel Saddles for horizontal vessels Standard for vertical vessels Leg support for vertical vessels Lug support for vertical vessels Heat exchanger nomenclature Heat-Exchanger Nozzle position Vessel front Klöpper form Vessel front Korbbogen form

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 5 OF 6

REV. 0

STRUCTURAL STEEL Document no 30101-30-17D-600 30101-30-17D-601 30101-30-17D-602 30101-30-17D-603 30101-30-17D-604 30101-30-17D-605 30101-30-17D-606 30101-30-17D-607 30101-30-17D-608 30101-30-17D-609

Rev No of sh't 0 1 0 1 0 1 0 1 0 1 0 1 0 2 0 1 0 1 0 1

Description IPE-Steel HE - A Steel HE - B Steel UNP Steel Equal L Steel Unequal L Steel General arrangement stairways Cage ladder Cage ladder at column Typical detail of Handrail

INSTRUMENTS Document no 30101-30-17D-700 30101-30-17D-701

0 Rev.

01/2002 Date

Rev No of Description sh't 0 2 Straight length requirements for flow elements 0 1 Orientation for orifice flanges

First Issue

LEA Prepared

Description PIPING HANDBOOK

INDEX Doc. No : 30101-30-17D-001 M:\BU3\30101\30\PIPING.MAN\PIPING.MAN\30101-30-17D-001.doc

BAA Checked

Approved

SHT. 6 OF 6

REV. 0

ABBREVIATIONS FOR PIPING DRAWINGS ACC. ASS.

According Assembly

BAVA BE BF B.O.M B.O.P. BW

Ball Valve Bevelled end Bottom Flat Bill of Material Bottom of Pipe Butt Weld

CHVA CONC. COND. CONT. CPLG CV

Check Valve Concentric Condensate Continuation Coupling Control Valve

DEG. DESCR. DIA. DR. DWG DISCH.

Degree Description Diameter Drain Drawing Discharge

E ECC. ELB. EL. EFD EL.TR.

East Eccentric Elbow Elevation Engineering Flow Diagram Electric Tracing

FAB. FF FB FLG FO FC FOF FW FP FI FE

Fabrication Flat Face Full Bore Flange Failure Open Failure Close Face of Flange Field Weld Fixed point Flow Indicator Flow Element

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ABBREVIATIONS Doc. No : 30101-30-17D-100 C:\webpage\piping_std\30101-30-17D-100.doc

BAA Checked

Approved

SHT. 1 OF 5

REV. 0

GAVA GLVA

Gate Valve Globe Valve

HC HCPLG HP HOR.

Hose Connection Half Coupling High Pressure Horizontal

ID INS.

Inside Diameter Insulation

L LC LG LI LO LJ LP

Length Locked Closed Level Gauge Level Indicator Locked Open Lap Joint Low Pressure

MAT. MAX. MIN. MISC. ML MM M MTO

Material Maximum Minimum Miscellaneous Make-up Length Millimeter Meter Material Take-Off

N NC NO NIPP. NR. NPT NTS

North Normally Closed Normally Open Nipple Number USA National Pipe Thread Not to Scale

OD

Outside Diameter

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ABBREVIATIONS Doc. No : 30101-30-17D-100 C:\webpage\piping_std\30101-30-17D-100.doc

BAA Checked

Approved

SHT. 2 OF 5

REV. 0

PC PI PEFD PLT PR PP PREFAB PRESS. PL. EL

Pressure Controller Pressure Indicator Process Engineering Flow Diagram Plate Pressure Recorder Personal Protection Prefabrication Pressure Platform Elevation

R RED. REF. REINF. REV. RF RTJ. RO RV RB

Radius Reducer Reference Reinforcing Revision Raised Face Ring Type Joint Restriction Orifice Relief Valve Reduced Bore

S SB SC SCH. SCRD SG SHT SMLS SO.FLG SPEC. SR STM STD. STR. STM TR. SS SUCT. SP. SW. SWG. SV. SPW. STDB.

South Spectacle Blind Sample Connection Schedule Screwed Sight Glass Sheet Seamless Slip-on Flange Specification Short Radius Steam Standard Strainer Steam Tracing Stainless Steel Suction Sliding Point Socket Weld Swaged Safety Valve Spiral Wound Stud Bolt

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ABBREVIATIONS Doc. No : 30101-30-17D-100 C:\webpage\piping_std\30101-30-17D-100.doc

BAA Checked

Approved

SHT. 3 OF 5

REV. 0

TEMP. TF. THR. T.S.O. TW TI TYP. T.O.C. T.O.S.

Temperature Top Flat Threaded Tight Shut Off Thermowell Temperature Indicator Typical Top of Concrete Top of Steel

UC. US. UFD.

Utility Connection Utility Station Utility Flow Diagram

V. VAC. VERT.

Vent Vacuum Vertical

W. WN. WP. WT

West Welding Neck Flange Work Point. Wall Thickness

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ABBREVIATIONS Doc. No : 30101-30-17D-100 C:\webpage\piping_std\30101-30-17D-100.doc

BAA Checked

Approved

SHT. 4 OF 5

REV. 0

ABBREVIATIONS FOR PIPE NIPPELS BEB BEP BET

Both Ends Bevelled Both Ends Plain Both Ends Threaded

OEB OEP OET

One End Bevelled One End Plain One End Threaded

LEP LEB LET

Large End Plain Large End Bevelled Large End Threaded

SEP SEB SET

Small End Plain Small End Bevelled Small End Threaded

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ABBREVIATIONS Doc. No : 30101-30-17D-100 C:\webpage\piping_std\30101-30-17D-100.doc

BAA Checked

Approved

SHT. 5 OF 5

REV. 0

From metric to Imperial multiply

General factors for Conversion : LENGTH : 1 inch = 25,4 mm 1 foot = 304,8 mm 1 yard = 914,4 mm 1 mile = 1609 m 1 nautical = 1852 m mile

1 mm 1m 1m 1 km 1 km

= 0,0254 m = 0,3048 m = 0,9144 m = 1,609 km = 1,852 km

= = = = =

0,0394 in 3,2808 ft 1,0936 yd 0,6215 mile 0,5399 nautical mile

AREA : cm2 x m2 x m2 x m2 x km2 x

0,155 10,764 1,196 0,0002471 0,386

= = = = =

1 lb. = 0,454 kg 1 cwt = 50,80 kg 1 (long) ton = 1016,0 kg 1 short ton = 907,2 kg

1 kg 1 kg 1 kg 1 kg

2,2046 0,0197 0,0009842 0,0011023

= = = =

VOLUME: 1 in3 1 yd3 1 ft3

cm3 x 0,06102 m3 x 35,3147 m3 x. 1,3079

= in3 = ft3 . = yd3

litre x 0,0063 litre x 0,22 litre x 0,2642

= barrel = UK gal = US gal

1 in2 = 6,45 cm2 2 1 ft = 0,0929 m2 1 yd2 = 0,836 m2 1 acre = 4047 m2 1 sq. mile = 2,5899 km2

in2 ft2 yd2 acre sq mile

WEIGHT / MASS :

= 16,3871 cm3 = 0,7646 m3 = 0,0283 m3

x x x x

lb. cwt long ton short ton

CONTENTS: 1 barrel = 1 UK gallon = 1 US gallon =

0 Rev.

01/2002 Date

159 litres 4,55 litres 3,785 litres

First Issue Description

LEA Prepared

PIPING HANDBOOK CONVERSION FROM METRIC TO IMPERIAL Doc. No : 30101-30-17D-101 C:\webpage\piping_std\30101-30-17D-101.doc

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

From metric to Imperial multiply

General factors for Conversion : PRESSURE AND STRESS: 1 lb/in2 (psi) 1 lb/ft2 (psi) 1 Long ton / in2 1 Long ton / ft2 1 Short ton / in2 1 Short ton / ft2

= = = = = =

0,0703 kgf / cm2 4,8824 kgf / m2 1,5749 kgf / mm2 10,9366 tf / m2 1,4061 kgf / mm2 9,7651 tf / m2

Kgf / cm2 Kgf / m2 Kgf / mm2 Tf / m2 Kgf / mm2 Tf / m2

x 14,2233 = lb / in2 x 0,2048 = lb / ft2 x 0,635 = long t / in2 x 0,0914 = long t / ft2 x 0,7112 = short t / in2 x 0,1024 = short t / ft2

SUNDRY CONVERSION FACTORS :

1 km / ltr 1 kg 1 kg / m

0 Rev.

01/2002 Date

= 2,8225 mpg = 0,1573 stone = 0,67197 lb./ ft

1 mpg 1 stone 1 kg / m

First Issue Description

= 0,3536 km / ltr = 6,3503 kg = 1,4882 kg / m

LEA Prepared

PIPING HANDBOOK CONVERSION FROM METRIC TO IMPERIAL Doc. No : 30101-30-17D-101 C:\webpage\piping_std\30101-30-17D-101.doc

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

Centigrade / Centigrade-Fahrenheit / Fahrenheit -459,4

up to

-130

-120

up to

22

23

up to

59

60

up to

94

95

up to

370

C

C/F

F

C

C/F

F

C

C/F

F

C

C/F

F

C

C/F

F

-273 -268 -262 -257 -251

-459,4 -450 -440 -430 -420

-84 -79 -73 -68 -62

-120 -110 -100 -90 -80

-184 -166 -148 -130 -112

-5 -4,4 -2,8 -2,2 -1,7

23 24 27 28 29

73,4 75,2 80,6 82,4 84,2

15,6 16,1 16,7 17,2 17,8

60 61 62 63 64

140 141,8 143,6 145,4 147,2

35 35,6 36,1 36,7 37,2

95 96 97 98 99

203 204,8 206,6 208,4 210,2

-246 -240 -234 -229 -223

-410 -400 -390 -380 -370

-57 -51 -46 -40 -34

-70 -60 -50 -40 -30

-94 -76 -58 -40 -22

-1,1 -0,6 0 0,6 1,1

30 31 32 33 34

86 87,8 89,6 91,4 93,2

18,3 18,9 19,4 20 20,6

65 66 67 68 69

149 150,8 152,6 154,4 156,2

37,8 38 43 49 54

100 100 110 120 130

212 212 230 248 266

-218 -212 -207 -201 -196

-360 -350 -340 -330 -320

-29 -23 -17,8 -17,2 -16,7

-20 -10 0 1 2

-4 14 32 33,8 35,6

1,7 2,2 2,8 3,3 3,9

35 36 37 38 39

95 96,8 98,6 100,4 102,2

21,1 21,7 22,2 22,8 23,3

70 71 72 73 74

158 159,8 161,6 163,4 165,2

60 66 71 77 82

140 150 160 170 180

284 302 320 338 256

-190 -184 -179 -173 -169

-310 -300 -290 -280 -273

-459,4

-16,1 -15,6 -15 -14,4 -13,9

3 4 5 6 7

37,4 39,2 41 42,8 44,6

4,4 5 5,6 6,1 6,7

40 41 42 43 44

104 105,8 107,6 109,4 111,2

23,9 24,4 25 25,6 26,1

75 76 77 78 79

167 168,8 170,6 172,4 174,2

88 93 99 100 104

190 200 210 212 220

374 392 410 413,6 428

-168 -162 -157 -151 -146

-270 -260 -250 -240 -230

-454 -436 -418 -400 -382

-13,3 -12,8 -12,2 -11,7 -11,1

8 9 10 11 12

46,4 48,2 50 51,8 53,6

7,2 7,8 8,3 8,9 9,4

45 46 47 48 49

113 114,8 116,6 118,4 120,2

26,7 27,2 27,8 28,3 28,9

80 81 82 83 84

176 177,8 179,6 181,4 183,2

110 116 121 127 132

230 240 250 260 270

446 464 482 500 518

-140 -134 -129 -123 -118

-220 -210 -200 -190 -180

-364 -346 -328 -310 -292

-10,6 -10 -9,4 -8,9 -8,3

13 14 15 16 17

55,4 57,2 59 60,8 62,6

10 10,6 11,1 11,7 12,2

50 51 52 53 54

122 123,8 125,6 127,4 129,2

29,4 30 30,6 31,1 31,7

85 86 87 88 89

185 186,8 188,6 190,4 192,2

138 143 149 154 160

280 290 300 310 320

536 554 572 590 608

-112 -107 -101 -96 -90

-170 -160 -150 -140 -130

-274 -256 -238 -220 -202

-7,8 -7,2 -6,7 -6,1 -5,6

18 19 20 21 22

64,4 66,2 68 69,8 71,6

12,8 13,3 13,9 14,4 15

55 56 57 58 59

131 132,8 134,6 136,4 138,2

32,2 32,8 33,3 33,9 34,4

90 91 92 93 94

194 195,8 197,6 199,4 201,2

166 171 177 182 188

330 340 350 360 370

626 644 662 680 698

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK CONVERSION TABLE FOR TEMPERATURES Doc. No : 30101-30-17D-102 C:\webpage\piping_std\30101-30-17D-102.doc

BAA Checked

Approved

SHT. 1 OF 3

REV. 0

Centigrade / Centigrade-Fahrenheit / Fahrenheit

0 Rev.

380

up to

720

730

up to

1070

1080

up to

1420

1430

up to

1770

1780

up to

2120

C

C/F

F

C

C/F

F

C

C/F

F

C

C/F

F

C

C/F

F

193 199 204 210 216

380 390 400 410 420

716 734 752 770 788

388 393 399 404 410

730 740 750 760 770

1346 1364 1382 1400 1418

582 588 593 599 604

1080 1090 1100 1110 1120

1976 1994 2012 2030 2048

777 782 788 793 799

1430 1440 1450 1460 1470

2606 2624 2642 2660 2678

971 977 982 988 993

1780 1790 1800 1810 1820

3236 3254 3272 3290 3308

221 227 232 238 243

430 440 450 460 470

806 824 842 860 878

416 421 427 432 438

780 790 800 810 820

1436 1454 1472 1490 1508

610 616 621 627 632

1130 1140 1150 1160 1170

2066 2084 2102 2120 2138

804 810 816 821 827

1480 1490 1500 1510 1520

2696 2714 2732 2750 2768

999 1004 1010 1016 1021

1830 1840 1850 1860 1870

3326 3344 3362 3380 3398

249 254 260 266 271

480 490 500 510 520

896 914 932 950 968

443 449 454 460 466

830 840 850 860 870

1526 1544 1562 1580 1598

638 643 649 654 660

1180 1190 1200 1210 1220

2156 2174 2192 2210 2228

832 838 843 849 854

1530 1540 1550 1560 1570

2786 2804 2822 2840 2858

1027 1032 1038 1043 1049

1880 1890 1900 1910 1920

3416 3434 3452 3470 3488

277 282 288 293 299

530 540 550 560 570

986 1004 1022 1040 1058

471 477 482 488 493

880 890 900 910 920

1616 1634 1652 1670 1688

666 671 677 682 688

1230 1240 1250 1260 1270

2246 2264 2282 2300 2318

860 866 871 877 882

1580 1590 1600 1610 1620

2876 2894 2912 2930 2948

1054 1060 1066 1071 1077

1930 1940 1950 1960 1970

3506 3524 3542 3560 3578

304 310 316 321 327

580 590 600 610 620

1076 1094 1112 1130 1148

499 504 510 516 521

930 940 950 960 970

1706 1724 1742 1760 1778

693 699 704 710 716

1280 1290 1300 1310 1320

2336 2354 2372 2390 2408

888 893 899 904 910

1630 1640 1650 1660 1670

2966 2984 3002 3020 3038

1082 1088 1093 1099 1104

1980 1990 2000 2010 2020

3596 3614 3632 3650 3668

332 338 343 349 354

630 640 650 660 670

1166 1184 1202 1220 1238

527 532 538 543 549

980 990 1000 1010 1020

1796 1814 1832 1850 1868

721 727 732 738 743

1330 1340 1350 1360 1370

2426 2444 2462 2480 2498

916 921 927 932 938

1680 1690 1700 1710 1720

3056 3074 3092 3110 3128

1110 1116 1121 1127 1132

2030 2040 2050 2060 2070

3686 3704 3722 3740 3758

360 366 371 377 382

680 690 700 710 720

1256 1274 1292 1310 1328

554 560 566 571 577

1030 1040 1050 1060 1070

1886 1904 1922 1940 1958

749 754 760 766 771

1380 1390 1400 1410 1420

2516 2534 2552 2570 2588

943 949 954 960 966

1730 1740 1750 1760 1770

3146 3164 3182 3200 3218

1138 1143 1149 1154 1160

2080 2090 2100 2110 2120

3776 3794 3812 3830 3848

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK CONVERSION TABLE FOR TEMPERATURES Doc. No : 30101-30-17D-102 C:\webpage\piping_std\30101-30-17D-102.doc

BAA Checked

Approved

SHT. 2 OF 3

REV. 0

Centigrade / Centigrade-Fahrenheit / Fahrenheit 2130

up to

2420

2430

up to

2720

2730

up to

C

C/F

F

C

C/F

F

C

C/F

F

1166

2130

3866

1332

2430

4406

1499

2730

4946

1171

2140

3884

1338

2440

4424

1504

2740

4964

1177

2150

3902

1343

2450

4442

1510

2750

4982

1182

2160

3920

1349

2460

4460

1516

2760

5000

1188

2170

3938

1354

2470

4478

1521

2770

5018

1193

2180

3956

1360

2480

4496

1527

2780

5036

1199

2190

3974

1366

2490

4514

1532

2790

5054

1204

2200

3992

1371

2500

4532

1538

2800

5072

1210

2210

4010

1377

2510

4550

1543

2810

5090

1216

2220

4028

1382

2520

4568

1549

2820

5108

1221

2230

4046

1388

2530

4586

1554

2830

5126

1227

2240

4064

1393

2540

4604

1560

2840

5144

1232

2250

4082

1399

2550

4622

1566

2850

5162

1238

2260

4100

1404

2560

4640

1571

2860

5180

1243

2270

4118

1410

2570

4658

1577

2870

5198

1249

2280

4136

1416

2580

4676

1582

2880

5216

1254

2290

4154

1421

2590

4694

1588

2890

5234

1260

2300

4172

1427

2600

4712

1593

2900

5252

1266

2310

4190

1432

2610

4730

1599

2910

5270

1271

2320

4208

1438

2620

4748

1604

2920

5288

1277

2330

4226

1443

2630

4766

1610

2930

5306

1282

2340

4244

1449

2640

4784

1616

2940

5324

1288

2350

4262

1454

2650

4802

1621

2950

5342

1293

2360

4280

1460

2660

4820

1627

2960

5360

1299

2370

4298

1466

2670

4838

1632

2970

5378

1304

2380

4316

1471

2680

4856

1638

2980

5396

1310

2390

4334

1477

2690

4874

1643

2990

5414

1316

2400

4352

1482

2700

4892

1649

3000

5432

1321

2410

4370

1488

2710

4910

1327

2420

4388

1493

2720

4928

0 Rev.

01/2002 Date

3000 C

First Issue Description

C/F

F

LEA Prepared

PIPING HANDBOOK CONVERSION TABLE FOR TEMPERATURES Doc. No : 30101-30-17D-102 C:\webpage\piping_std\30101-30-17D-102.doc

C

C/F

F

BAA Checked

Approved

SHT. 3 OF 3

REV. 0

PRESSURE AND STRESS IN NEWTON 10n N/m2 n N/m2 9 GN/m2 8 7 6 MN/m2 5 4 3 kN/m2 2 hN/m2 1 daN/m2 0 N/m2 -1 dN/m2 -2 cN/m2 -3- mN/m2 -4

N/dm2

N/cm2

MN/dm2 kN/cm2 hN/cm2 daN/cm2 N/cm2 dN/cm2 cN/cm2 mN/cm2

kN/dm2 hN/dm2 daN/dm2 N/dm2 dN/dm2 cN/dm2 mN/dm2

N/mm2 kN/mm2 hN/mm2 daN/mm2 N/mm2 dN/mm2 cN/mm2 mN/mm2

Ca. 1 kgf/mm2 1 kgf/cm2 1 kgf/dm2 1 kgf/m2

µN/mm2 1 kgf/cm2 µN/cm2

N/m2 = Pa mN/mm

µN/dm

2

2

nN/cm2

-5 -6

µN/m

2

ISO = heavy print is the most usual

from 2

to kN/m2 6,895

2

N/m MN/m 1 lb/in 6,895. 103 1 lb/ft2 47,88 1 ltn/in2 15,44. 106 15,44 2 3 1 ltn/ft 107,25. 10 107,25 1 sht tn/in2 13,789. 106 13,789 1 sht tn/ft2 95,763. 103 95,763 Example: 1 lb/in2 = 6,895 kN/m2 1 lb/in2 = 0.0703 kgf/cm2 from lb/ft2 ltn/in2 lb/in2 2 -3 N/m 0,145. 10 0,02089 0,06476. 10-6 kN/m2 0,145 MN/m2 0,06476. 2

kgf/mm2 kgf/cm2 kgf/m2 tf/m2

0 Rev.

01/2002 Date

kgf/mm

2

to kgf/cm2 0,0703

kgf/m2

tf/m2

4,8824 1,5749 10,9366 1,4061 9,7651 1 kN/m = 0.145 lb/in2 1 kgf/cm2 = 14.2234 lb/in2 2

to ltn/ft2 sht tn/in2 -3 0,00932. 10 0,0725. 10-6 0,00932 0,0725

0,635

sht tn/ft2 0,01044. 10-3 0,01044

0,7112

14,2234 0,2048 0,0914

First Issue Description

0,1024

LEA Prepared

PIPING HANDBOOK CONVERSION OF PRESSURE AND STRESS TO NEWTON Doc. No : 30101-30-17D-103 C:\webpage\piping_std\30101-30-17D-103.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

PRESSURE RATINGS ACC. ANSI B 16.5-1958 and API STD. 600-1957

Pressure rating ANSI Hydr.static test press.

Operating temp 20-100 150 In 0F 200 250 300 350 400 450 500 550 600 650 700 750 800 850 875 900 925 950 975 1000 1025 1050 1075 1100 1125 1150 1175 1200 1225 1250 1275 1300 1325 1350 1375 1400 1425 1450 1475 1500 1 1,2

150 425

Pressures are in Psig carbon steel 300 400 600 900 1100 1450 2175 3250

275 720 960 1440 255 710 945 1420 240 700 930 1400 225 690 920 1380 210 680 910 1365 195 675 900 1350 180 665 890 1330 165 650 870 1305 150 625 835 1250 140 590 790 1180 130 555 740 1110 120 515 690 1030 110 470 635 940 100 425 575 850 92 365 490 730 3001 4001 6001 821 2601 3501 5251 751 2251 2951 4451 701 1.2 1.2 1.2 190 250 3751.2 60 1.2 1.2 1.2 155 205 3101.2 55 501.2 1201.2 1601.2 2401.2 851.2 1151.2 1701.2 401.2

2160 2130 2100 2070 2050 2025 2000 1955 1875 1775 1660 1550 1410 1275 1100 9001 7851 6701 5651.2 4651.2 3601.2 2551.2

1500 5400

2500 9000

3600 3550 3500 3450 3415 3375 3330 3250 3125 2955 2770 2580 2350 2125 1830 15001 13051 11151 9451.2 7701.2 6001.2 4301.2

6000 5915 5830 5750 5690 5625 5550 5430 5210 4925 4620 4300 3920 3550 3050 25001 21801 18551 15701.2 12851.2 10001.2 7151.2

150 425

Cr Mo 1 - 0,5 300 400 1100 1450

600 2175

900 3250

1500 5400

2500 9000

2415 2250 2080 1915 1830 1750 1665 1585 1500 1285 1070 855 670 480 3751.2 2651.2 2201.2 1701.2

4025 3745 3470 3190 3055 2915 2775 2640 2500 2145 1785 1430 1115 800 6201.2 4451.2 3651.2 2851.2

Same value as carbon steel

110 100 92 82 75 70 60 55 50 40

485 645 965 450 600 900 415 555 835 385 510 765 365 490 735 350 465 700 335 445 665 315 420 635 300 400 600 255 345 515 215 285 430 170 230 345 135 180 265 95 130 190 751.2 1001.2 1501.2 551.2 701.2 1051.2 451.2 601.2 851.2 351.2 451.2 701.2

1450 1350 1250 1150 1100 1050 1000 950 900 770 645 515 400 290 2251.2 1601.2 1301.2 1051.2

This value to be used in relation with Power Boilers, Section 1, 1959, ASME Boiler and Pressure Vessel Code, table P 7 This value to be used in relation with Power Piping, Section 1, ANSI B 31.1, 1955, Code for Pressure Piping, table 2a

HOLD FOR LAATSTE ISSUE ANSI B 31.1

0 Rev.

01/2002 Date

Approved Description

LEA Prepared

PIPING HAND BOOK PRESSURE RATINGS ACCORDING ANSI Doc. No : 30101-30-17D-104 C:\webpage\piping_std\30101-30-17D-104.doc

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

PRESSURE RATINGS ACC. ANSI B 16.5-1958 and API STD. 600-1957

Pressure rating ANSI Hydr. static test press.

150 425

Operating temp. 20-100 150 In 0F 200 250 300 350 400 450 500 550 600 650 700 750 800 850 875 900 925 950 975 1000 1025 1050 1075 1100 1125 1150 1175 1200 1225 1250 1275 1300 1325 1350 1375 1400 1425 1450 1475 1500

275 255 240 225 210 195 180 165 150 140 130 120 110 100 92 82 75 70 60 55 50 40

0 Rev.

01/2002 Date

Pressure ratings are in PSIG AISI 347 and 321 300 400 600 900 1500 2500 150 1100 1450 2175 3250 5400 9000 425

720 710 700 690 680 675 665 650 625 590 555 515 495 470 450 425 415 400 390 380 370 355 345 335 325 310 300 260 215 170 140 115 95 75 65 50 45 40 35 30 30 25

960 945 930 920 910 900 890 870 835 790 740 690 660 625 595 565 550 535 520 505 490 475 460 445 430 415 400 345 290 230 190 150 125 100 85 70 60 55 50 40 40 35

1440 1420 1400 1380 1365 1350 1330 1305 1250 1180 1110 1030 985 940 895 850 825 805 780 760 735 715 690 670 645 625 600 520 430 345 285 225 190 150 125 105 95 80 70 60 55 50

2160 2130 2100 2070 2050 2025 2000 1955 1875 1775 1660 1550 1480 1410 1345 1275 1240 1205 1175 1140 1105 1070 1035 1000 970 935 900 780 650 515 425 340 285 225 190 155 140 125 110 95 85 75

3600 3550 3500 3450 3415 3375 3330 3255 3125 2955 2770 2580 2465 2355 2240 2125 2070 2010 1955 1900 1840 1785 1725 1670 1615 1555 1500 1305 1080 855 710 565 470 375 315 255 230 205 180 155 140 130

6000 5915 5830 5750 5690 5625 5550 5430 5210 4925 4620 4300 4110 3920 3730 3540 3445 3350 3260 3165 3070 2975 2880 2785 2690 2595 2500 2170 1800 1430 1185 945 785 630 530 430 385 345 300 255 235 215

300 1100

400 1450

AISI 316 600 900 2175 3250

2500 9000

1455 1310 1165 1035 910 795 685 575 465 405 345 300 255 215 170

2430 2185 1945 1730 1515 1330 1145 955 770 670 570 500 430 355 285

Same value as AISI 347 and 321

Approved Description

290 260 235 205 180 160 135 115 95 80 70 60 50 45 35

390 350 310 275 240 215 185 155 125 105 90 80 70 55 45

LEA Prepared

PIPING HAND BOOK PRESSURE RATINGS ACCORDING ANSI Doc. No : 30101-30-17D-104 C:\webpage\piping_std\30101-30-17D-104.doc

1500 5400

585 525 465 415 365 320 275 230 185 160 135 120 105 85 70

875 785 700 620 545 480 410 345 280 240 205 180 155 130 105

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

o

Press. Ratings Material 1 Cast Iron Nodular Cast Iron 2,5 Cast Iron Nodular Cast Iron 6 Cast Iron Nodular Cast Iron 10 Cast Iron Nodular Cast Iron C22 N, GS-45 16 Cast Iron Nodular Cast Iron C22 N, GS-25 25 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 40 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 63 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 100 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 160 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 250 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 320 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 400 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10

Allowable working pressure in bar at C 120 200 250 300 350 400 425 450 475 500 510 520 530 540 550 1 1 1 1 2,5 6 10

16 16 25

40

63

100

160

250

320

400

2

1,8

1,5

5 4,5 2 3,6 2 8

7

2

6

2

13 11 3 10 3 14 13 11 10 8 22 20 17 16 13 25 22 20 19 18 17 25 24 23 22 21 20 18 15 35 32 28 24 21 40 35 31 30 29 28 40 38 36 35 34 33 29 24 50 45 40 36 32 63 56 50 47 46 45 63 61 58 57 56 53 47 40 80 70 60 56 50 100 87 78 74 72 70 100 95 91 89 87 82 74 62 130 112 96 90 80 160 139 125 118 115 112 160 153 146 142 139 132 118 100 70 200 175 150 140 125 250 217 195 185 179 174 250 238 227 223 217 206 184 154 124 108 250 225 192 180 160 320 278 250 236 230 222 320 304 292 285 278 264 237 200 158 139 320 280 240 225 200 400 348 312 296 286 278 400 380 364 356 348 330 295 250 198 174

12

9

19

15

32

25

49

38

79 61

62 52

46

35

124 95

97 81

73

54

158 124 121 104

93

69

198 156 116 151 130

87

1) The test pressure is 1,5 x the operation pressure unless otherwise mentioned 2) When bolts of material 5D are used, the working pressure at 200oC is also allowed here. 3) When bolts of material 5D are used, the working pressure of C22 N is allowed here.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK PRESSURE CLASSES ACCORDING DIN 2401 Doc. No : 30101-30-17D-105 C:\webpage\piping_std\30101-30-17D-105.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

0 Rev.

10 / 2001 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK PRESSURE-TEMPERATURE TABLE ANSI-DIN Doc. No : 30101-30-17D-106 C:\webpage\piping_std\30101-30-17D-106.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

ASTM, DIN EN ISO NORMEN ASTM

(American Society for Testing and Materials)

ASTM A 182 ASTM A 193 ASTM A 213

ASTM A 451 ASTM A 473 ASTM A 511 ASTM A 530

Rvs gesmede fittingen, flenzen en afsluiters. Rvs boutmaterialen voor hoge temperaturen Naadloze rvs buizen voor o.a. warmtewisselaars en verdampers. Gelaste buizen, gelast zonder toevoegmateriaal voor o.a. condensors en warmtewisselaars. Naadloze en gelaste rvs buizen voor algemene toepassing met nauwe toleranties. Naadloze en gelaste pijp, gelaste pijp zonder toevoegmateriaal, voor algemene toepassing. Gelaste pijpen met toevoeg materiaal. Klasse 1 tweezijdig gelast en 100% radiografisch onderzoek. Klasse 2 tweezijdig gelast zonder radiografisch onderzoek. Klasse 3 eenzijdig gelast en 100% radiografisch onderzoek. Klasse 4 eenzijdig gelast, de las aan de binnenkant van de pijp zonder toevoegmateriaal en 100% radiografisch onderzoek. Klasse 5 tweezijdig gelast en plaatselijk radiografisch onderzoek. Rvs fittingen. Gelaste austenitische pijp (grote diam.) voor corrosie of hoog temperatuur gebruik. Algemene norm voor koolstof, ferrietisch en austenitisch gelegeerd stalen buis. Norm voor rvs centrifugaal gegoten buis. Roestvrijstalen en hittebestendige smeedstukken. Naadloze roestvrijstalen machinepijp. Speciaal koolstof en gelegeerd stalen pijp.

ANSI

(American National Standards Institute)

ASTM A 249 ASTM A 269 ASTM A 312 ASTM A 358

ASTM A 403 ASTM A 409 ASTM A 450

ANSI ANSI ANSI ANSI ANSI

ANSI B.16.28 ANSI B.36.1 9

Pijpdraad volgens ASTM. Rvs flenzen volgens ASTM. Rvs fittingen volgens ASTM. Gesmede las- en draadfittingen volgens ASTM. Laskant voorbereiding van buizen, fittingen, flenzen en afsluiters volgens ASTM. Rvs lasbochten Short-Radius volgens ASTM. Rvs pijp volgens ASTM.

MSS

(Manufacturers Standardisation Society)

MSS SP.6 MSS SP.25 MSS SP.39 MSS SP.43

Toleranties van rvs flenzen volgens ASTM. Merk systeem voor ASTM fittingen, flenzen en koppelingen. Rvs bouten en moeren volgens ASTM. ASTM lasfittingen.

0 Rev.

B.2.1 B. 1 6.5 B.16.9 B.16.11 B.16.25

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ASTM, DIN and ISO NORMS Doc. No : 30101-30-17D-107 C:\webpage\piping_std\30101-30-17D-107.doc

BAA Checked

Approved

SHT. 1 OF 3

REV. 0

ASTM, DIN EN ISO NORMEN DIN

(Deutsches lnstitut für Normierung)

DIN 17440

Roestvrijstaalprodukten technische leveringsvoorwaarden voor plaat, strip, draad, staf, smeedstukken en halfprodukten. Roestvrijstalen producten, technische leveringsvoorwaarden voor koudgewalste strip, spiraal en plaat. Gelaste ronde roestvrijstalen buizen voor algemene toepassingen. Gelaste ronde austenitische roestvrijstalen buizen voor speciale toepassingen. Naadloze ronde austenitische roestvrijstalen buizen voor speciale toepassingen. Pijpschroefverbinding met snijring Toleranties voor rvs naadloze buis. Toleranties voor rvs gelaste buis. Lasbochten Lasbochten Las - T- stukken Las – verlopen Laskappen Voorlasflenzen ND 10 Voorlasflenzen ND 16 Voorlasflenzen ND 25 Voorlasflenzen ND 40 Boordringen ND 10 en flenzen Vlakke aanlasflenzen ND 10 Blindflenzen ND 16 – 100 Stalen draadfittingen. Stalen draadfittingen. - nippels Stalen draadfittingen. - sokken Stalen draadfittingen zoals : - kruisstukken - T – stukken - Bochten Cilindrische binnen- en buiten pijpgasdraad. Cilindrische binnen- en conische buiten pijpgasdraad

DIN 17441 DIN 17455 DIN 17457 DIN 17458 DIN 2353 DIN 2462 DIN 2463 DIN 2605 DIN 2606 DIN 2615 DIN 2616 DIN 2617 DIN 2632 DIN 2633 DIN 2634 DIN 2635 DIN 2642 DIN 2576 DIN 2527 DIN 2980 DIN 2982 DIN 2986 DIN 2987

DIN 259 DIN 2999

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ASTM, DIN and ISO NORMS Doc. No : 30101-30-17D-107 C:\webpage\piping_std\30101-30-17D-107.doc

BAA Checked

Approved

SHT. 2 OF 3

REV. 0

ASTM, DIN EN ISO NORMEN ISO

(International Organization for Standardization)

ISO 228 / 1

Pijpdraad, waarbij geen drukvaste verbindingen op de draad worden gemaakt. Deel 1: benaming afmeting tolerantie Pijpdraad, waarbij geen drukvaste verbindingen op de draad worden gemaakt. Deel 2: controle d.mv. tolerantiekalibers. Roestvrijstalen buizen; afmetingen, toleranties en standaard gewichten per eenheid. Stalen producten voor toepassing bij drukken. Kwaliteitseisen. Deel 5 langsnaadgelaste austenitische roestvrijstalen buizen. Roestvrijstalen draadfittingen volgens ISO 7 / 1. Roestvrijstalen lasfittingen.

ISO 228 / 2 ISO 1127 ISO 2604 / 5 ISO 4144 ISO 5251 .

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK ASTM, DIN and ISO NORMS Doc. No : 30101-30-17D-107 C:\webpage\piping_std\30101-30-17D-107.doc

BAA Checked

Approved

SHT. 3 OF 3

REV. 0

EN-Standards Publication NNI 1993 OLD

EURO STANDARD

EN- STANDARD

Max. 0C

St 37 - 2

Fe 360 BFN

DIN 17100

S 235 JRG 2

Acc. EN 10025

300

15 Mo 3

15 Mo 3

W st. 1.5415

16 Mo 3

Acc. EN 10028-2

500

13 CrMo 44

13 CrMo 44

W st. 1.7335

13 CrMo 4-5

Acc. EN 10028-2

500

H-II

H-II

DIN 17155

P 265 GH

Acc. EN 10028-2

400

X 5 CrNi 18.9

X 5 CrNi 18.10

DIN 17440

Acc. EN 10088-2

400

X 5 CrNi 18.10 (Bolts)

Grade A 1

Grade A 2

400

Bolts Grade 8.8 DIN 267

n.v.t

n.v.t

300

Nuts Grade 8 DIN 267

n.v.t

n.v.t

300

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HANDBOOK

EN STANDARDS Doc. No : 30101-30-17D-108 C:\webpage\piping_std\30101-30-17D-108.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

CONVERSION TABLE STAINLESS STEEL STANDARDS Germany USA W.stof nr AISI / UNS

Sweden SIS-norm

Afnor

Sandvik

Avesta

Valinox

Mannesmann

Ferritic – Austenitic stainless steel 1.4417

S 31500

2376

Z 2 CND 18-05

3 RE 60

3 RE 60

1.4460

329

2324

Z 2 CND 25-27A2

10 RE 51

25-5-1L

VLX 547

1.4462

S 31803

2377

Z 2 CND 22-05A2

SAF 2205

2205

VLX 562

1.4301

304

2333

Z 6 CN 18-09

5 R 10

18-9

VLX 304

AX 10

1.4306

304 L

2352

Z 2 CN 18-10

3 R 12

18-10 L

VLXTBC

AX 10 E

1.4311

304 LN

2371

Z 2 CN 18-10

3 R 19

18-9 LN

VLX 304 N

AX 10 H

Austenitic stainless steel

1.4361

Z 1 CNS 18-15

VLX 304 S

1.4401

316

2347

Z 6 CND 17-11

7 R 60

17-11-2

VLX 316

AX 20

1.4404

316 L

2348

Z 2 CND 17-12

3 R 60

17-11-2 L

VLXMoTBC

AX 20 E

1.4429

316 LN

2375

Z 2 CND 17-13

3 R 69

17-12-2,5 LN

VLX 316 N

AX 22 H

1.4435

316 L

2353

Z 2 CND 17-13

3 R 60

17-11-2,5 L

VLXMoTBC-3

AX 22 E

1.4436

316

2343

Z 6 CND 17-12

5 R 60

17-12-2,5

VLX 316-3

AX 22

1.4438

317 L

2367

Z 2 CND 19-15

3 R 64

18-13-3 L

VLX 317 L

AX 30 E

1.4439

S 31726

17-14- 4 LN

1.4465

2 RE 69

254 SFER

1.4539

N 08904

2562

Z 1 NCDU 25-20

2 RK 65

904 L

VLX 904

1.4541

321

2337

Z 6 CNT 18-10

8 R 30

18-10-Ti

VLXTi

AT 10

1.4550

347

2338

Z 6 CNNb 18-10

6 R 40

832 MVNb

VLXNb

AN 10

1.4571

316 Ti

2350

Z CNDT 17-12

8 R 70

17-11-2 Ti

VLXMo

AT 20

1.4841

310

Z 12 CNS 25-20

1.4845

310 S

Z 12 CN 25-20

S 31254

Z 12 CNDU 2018-6A2

VLX 25-20 7 RE 10

S 30815

0 Rev.

20 D 1

01/2002 Date

25-20

VLX 310

254 SMO

VLX 954

253 MA

First Issue

LEA Prepared

Description PIPING HANDBOOK

BAA Checked SHT.

1 OF 1 CONVERSION TABLE ST.STEEL STANDARDS Doc. No : 30101-30-17D-109 C:\webpage\piping_std\30101-30-17D-109.doc

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK TABLE FOR PIPE CAPACITY Doc. No : 30101-30-17D-110 C:\webpage\piping_std\30101-30-17D-110.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

TABLE FOR VELOCITY OF SEVERAL LIQUIDS and GASSES Medium 1

m / sec

Natural Gas

City gas house system Low pressure Middle pressure High pressure 2

1 3-8 5 – 10 10 – 25

up to 0,02 kg/cm2 up to 0,05 kg/cm2 up to 1 kg/cm2

Air

Compressed air systems Suction lines of vacumpumps

3

15 – 25 10 – 30

Condensate

Suction lines Discharge lines

4

0.5 – 1 1.5 – 3

Oil products

Heated heavy oil suction lines Heated heavy oil discharge lines Middle heavy oil long distance lines Petrol, benzol, gas oil suction lines Petrol, benzol, gas oil discharge lines

5

Steam

Low pressure saturated Middle pressure saturated High pressure saturated Superheated steam specific volume Superheated steam specific volume Superheated steam specific volume Superheated steam specific volume

6

0.5 – 0.8 1 – 1.5 1–2 0.5 – 0.8 1 – 1.25

16 ato 16 – 40 ato 40 – 125 ato

15 – 30 20 – 40 30 – 60

0,025 m3 / kg 0,05 m3 / kg 0,1 m3 / kg 0,2 m3 / kg

30 – 35 35 – 40 40 – 45 45 – 50

Water

Potable water long distance lines Potable water main headers Potable water distribution lines Cooling water suction lines Cooling water discharge lines Hot water long distance lines Hot water distribution lines

0 Rev.

01/2002 Date

1.5 – 3 1–2 0.5 – 0.7 0.6 – 1.3 0.8 – 2 1 – 2.5 0.8 - 2

First Isue Description

LEA Prepared

PIPING HAND BOOK TABLE FOR VELOCITY LIQUIDS AND GASSES Doc. No : 30101-30-17D-111 C:\webpage\piping_std\30101-30-17D-111.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

TABLE FOR NUMBER OF BRANCHES PER HEADER

H’dr ND 1/4”

Area OD approx. 1/4” mm mm2 13.72 28

3/8”

17.15

71

2.5

1

1/2”

21.34

126

4.5

2

1

3/4”

26.67

283

10

4

2

1

1”

33.4

507

18

7

4

2

1

11/2”

48.26

1134

40

16

9

4

2

1

2”

60.33

2026

71

28

16

7

4

1.8

1

21/2”

28.75

3167

113

44

25

11

6

2.8

1.6

1

3”

88.9

4560

167

64

36

16

9

4

2

1

1

4”

114.3

8107

290

113

64

28

16

7

4

2.6

1.8

1

6”

168.8

18147

640

256 144

64

36

16

9

5.8

4

2

1

8”

219.9

32365 1140 454 256 113

64

28

16

10

7

4

1.8

1

10”

273

50671 1800 712 400 178 100

44

25

16

11

6

2.8

1.6

0 Rev.

01/2002 Date

3/8”

1/2”

3/4”

1”

11/2”

2”

First Issue Description

21/2”

3”

LEA Prepared

PIPING HAND BOOK TABLE FOR BRANCHES PER HEADER Doc. No : 30101-30-17D-112 C:\webpage\piping_std\30101-30-17D-112.doc

4”

6”

8”

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

10”

1

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK TRIGONIOMETRIC FUNCTIONS Doc. No : 30101-30-17D-113 C:\webpage\piping_std\30101-30-17D-113.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

RULE OF THE THUMP

1

Pipe area Pipe area in cm2 is 5xD2, if D is in inches . Example with 4”pipe : area is 5 x 42 = 80 cm2.

2

Volume of pipe Volume of 1 meter pipe in litres = D2 : 2, if D is in inches . Example with 6” pipe : Volume is 62 : 2 = 18 litre

3

Quantity The quantity of liquid flowing through a pipe with a velocity in 1 m/s is (diameter in inches)2 x ½ x m/s = dm3/sec Example : 4”pipe, velocity of 4 m/s 42 x ½ x 4 = 32 dm3/sec

4

Expansion The linear expansion of 1 meter pipe if heated 1000 C will be approx.1 mm. Example : 200 meter pipe haeted 1500 C ; The expansion will be approx. 200 x 1.5 = 300 mm

5

Circumference of pipe The circumference of a pipe in cm is 8 x D, if D is in inches. Example diameter pipe is 3”: The circumference is 8 x 3 = 24 cm

6

Area of vessel head The area of a vessel head (korbbogenhead) is (diameter in meters)2 x 1.1 = m2 Example : diameter vessel head is 4 meter The area is 42 x 1.1 = 17.6 m2

7

Weight of steel plate The weight of a steel plate per m2 is thickness in millimetres x 7.85 = kgf/m2 Example : length is 4m, width 2 m, thick 10 mm The weight is 4 x 2x10 x 7.85 = 628 kgf/m2

0 Rev.

01/2002 Date

First Issue Description PIPING HAND BOOK

LEA Prepared

BAA Checked

SHT. 1 OF 1 RULE OF THE THUMP Doc. No : 30101-30-17D-114

C:\webpage\piping_std\30101-30-17D-114.doc

Approved REV. 0

STOOMWEZEN HYDROSTATIC TEST PRESSURE

Test pressure range; 0

up to 2.5 barg

1x+1

2.5 up to 20 barg

1.4 x +0

20 barg and above

1.3 x +2

Example

Design pressure

0 Rev.

01/2002 Date

X

Test pressure

1.5

barg

1. + 1

2.5

2.8

barg

1.4

4.0

19.2

barg

1.4

27.0

20.5

barg

1.3 + 2

28.0

48.2

barg

1.3 + 2

64.0

First Issue

LEA Prepared

Description PIPING HAND BOOK

TEST PRESSURE Doc. No : 30101-30-17D-115 C:\webpage\piping_std\30101-30-17D-115.docdoc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

0 Rev.

01/2002 Date

First Issue Description PIPING HANDBOOK

LEA Prepared

MIN. CLEARANCE FOR AVERAGE MAN Doc. No : 30101-30-17D-116 C:\webpage\piping_std\30101-30-17D-116.doc

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

0 Rev.

01/2002 Date

First Issue Description PIPING HANDBOOK

LEA Prepared

MIN. CLEARANCE FOR AVERAGE MAN Doc. No : 30101-30-17D-116 C:\webpage\piping_std\30101-30-17D-116.doc

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

Operating temperature 0C (up to) Nom diam. mm

+ 100

+ 150

+ 200

+ 250

+ 300

+350

15

25

25

25

25

25

30

20

25

25

25

25

25

25

25

25

25

25

40

25

25

25

50

25

25

80

25

100

+ 450

+ 500

40

40

50

30

40

40

50

25

30

40

40

50

25

25

30

40

40

50

25

25

25

40

40

50

60

25

25

25

30

40

40

50

60

25

25

25

25

30

40

50

50

70

150

25

25

25

25

30

40

50

60

70

200

25

25

25

25

30

40

50

60

80

250

25

25

25

25

30

40

50

60

80

300

25

25

25

25

30

40

50

60

80

350

25

25

25

25

30

40

50

70

80

400

25

25

25

25

30

40

50

70

80

450

25

25

25

25

30

40

50

70

80

500

25

25

25

40

40

40

50

70

80

Note: 1 Insulation thickness based on:

0 Rev.

01/2002 Date

+ 400

Ambient temperature: 5 deg. C Wind velocity: 4 m/s Capital charge: 17.5 % Heat cost: US $ 2.5/Gj Max. allowable surface temp.: 60 C Material cellular glass or polyurethane

First Issue Description

LEA Prepared

PIPING HAND BOOK STANDARD INSULATION THICKNESS Doc. No : 30101-30-17D-117 C:\webpage\piping_std\30101-30-17D-117.docdoc

BAA Checked

Approved

SHT. 1 OF 4

REV. 0

Standard insulation thickness in mm for heat conservation Operating temperature 0C (up to) Nom diam. mm

+ 100

+ 150

+ 200

+ 250

+ 300

+ 350

+ 400

+ 450

+ 500

15

30

30

30

30

40

40

50

50

60

20

30

30

30

30

40

40

50

50

60

25

30

30

30

30

40

40

50

50

60

40

30

30

30

40

50

50

60

60

70

50

30

30

40

50

50

60

60

70

70

80

30

40

50

50

60

70

70

70

70

100

30

40

50

60

70

70

80

90

100

150

40

50

50

60

80

90

100

100

100

200

40

50

60

80

90

100

110

120

120

250

50

60

70

80

100

100

110

120

130

300

50

60

70

80

100

110

120

120

130

350

50

60

70

80

100

110

120

120

130

400

50

70

70

90

100

120

120

130

140

450

50

70

80

90

110

120

120

130

150

500

60

70

80

100

120

120

120

140

150

Note: 1 Insulation thickness based on:

2

0 Rev.

Ambient temperature: 5 deg. C Wind velocity: 4 m/s Capital charge: 17.5 % Heat cost: US $ 2.5/Gj Insulation thickness for winterised traced lines (LP steam, hot water or electrical) 50 mm.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK STANDARD INSULATION THICKNESS Doc. No : 30101-30-17D-117 C:\webpage\piping_std\30101-30-17D-117.docdoc

BAA Checked

Approved

SHT. 2 OF 4

REV. 0

Standard insulation thickness in mm For equipment insulation Operating temperature 0C (up to) Nom diam. + 100 + 150 + 200 + 250 + 300 + 350 + 400 + 450 Standard insulation thickness in mm for personnel protection Vessel

25

25

25

40

40

40

50

+ 500

70

80

180

190

Standard insulation thickness in mm for heat conservation Vessel

80

100

110

130

Storage Tanks Walls

80

100

120

140

Storage Tanks Roofs

80

80

80

80

Note : 1 Insulation thickness based on :

0 Rev.

01/2002 Date

140

160

Ambient temperature: Wind velocity: Capital charge: Heat cost:

First Issue Description

180

5 deg. C 4 m/s 17.5 % US $ 2.5/Gj

LEA Prepared

PIPING HAND BOOK STANDARD INSULATION THICKNESS Doc. No : 30101-30-17D-117 C:\webpage\piping_std\30101-30-17D-117.docdoc

BAA Checked

Approved

SHT. 3 OF 4

REV. 0

Standard insulation thickness in mm for cold conservation Operating temperature 0C (up to) Nom diam. mm

0

- 20

- 40

-60

- 80

- 100

15

20

30

40

50

60

70

20

20

30

40

50

60

70

25

20

40

50

60

60

70

40

20

40

50

60

70

80

50

20

40

50

60

70

80

80

20

40

60

70

80

90

100

20

40

60

70

80

90

150

30

50

60

80

90

100

200

30

50

60

80

90

100

250

30

50

70

80

100

110

300

30

50

70

80

100

110

Vessel

30

50

80

100

120

140

Note: 1 Insulation thickness based on:

2

0 Rev.

Foamglass cellulair glass T4 Ambient temperature: 20 deg. C Wind velocity: 2.7 m/s Emissivity: 0.2 Thickness should be rounded off to the nearest higher manufacturer’s thickness.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK STANDARD INSULATION THICKNESS Doc. No : 30101-30-17D-117 C:\webpage\piping_std\30101-30-17D-117.docdoc

BAA Checked

Approved

SHT. 4 OF 4

REV. 0

DIMENSIONS AND PARTICULARS OF LINE PIPE Nom. pipe size inch

Schedule Numbers Note 1

Wall Thickn.

Inside Dia.

Inside Area

Metal Area

Outside Surface

Inside Surface

Weight Note 2

Weight Filled with water Kg/m

Moment of inertia

Section modules

Radius of gyration

cm4

cm3

cm

OD cm

A

B

C

cm

cm

cm2

cm2

m2/m

m2/m

Kg/m

1/8 1.029

40 80

Std XS

10 S 40 S 80S

0.124 0.173 0.241

0.780 0.683 0.546

0.477 0.366 0.235

0.353 0.464 0.597

0.032 0.032 0.032

0.025 0.021 0.017

0277 0.365 0.469. .

0.325 0.402 0.492

0.037 0.044 0.051

0.072 0.086 0.098

0.323 0.309 0.291

1/4 1.372

40 80

Std XS

10 S 40 S 80S

0.165 0.223 0.302

1.041 0.925 0.767

0.851 0.671 0.462

0.626 0.806 1.015

0.043 0.043 0.043

0.033 0.029 0.024

0.491 0.632 0.796

0.576 0.699 0.842

0.116 0.138 0.157

0.169 0.202 0.229

0.430 0.414 0.393

3/8 1.715

40 80

Std XS

10 S 40 S 80S

0.165 0.231 0.320

1.384 1.252 1.074

1.505 1.232 0.906

0.804 1.077 1.402

0.054 0.054 0.054

0.043 0.039 0.034

0.629 0.845 1.100

0.779 0.968 1.191

0.244 0.304 0.359

0.285 0.354 0.419

0.551 0.531 0.506

1/2 2.134

40 80 160 -

Std XS XXS

10 S 40 S 80S -

0.211 0.277 0.373 0.475 0.747

1.712 1.580 1.387 1.184 0.640

2.303 1.961 1.509 1.100 0.322

1.256 1.614 2.064 2.470 3.251

0.067 0.067 0.067 0.067 0.067

0.054 0.050 0.044 0.037 0.020

0.998 1.266 1.619 1.940 2.550

1.228 1.462 1.770 2.050 2.582

0.596 0.712 0.837 0.921 1.009

0.559 0.667 0.783 0.864 0.946

0.684 0.664 0.636 0.610 0.557

3/4 2.667

40 80 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.165 0.211 0.287 0.391 0.554 0.782

2.337 2.245 2.093 1.885 1.560 1.102

4.289 3.960 3.438 2.786 1.910 0.954

1.297 1.626 2.148 2.806 3.677 4.631

0.084 0.084 0.084 0.084 0.084 0.084

0.073 0.071 0.066 0.059 0.049 0.035

1.018 1.275 1.683 2.193 2.882 3.632

1.447 1.671. 2.025 2.472 3.073 3.727

1.020 1.236 1.540 1.865 2.194 2.410

0.765 0.928 1.157 1.398 1.645 1.809

0.886 0.871 0.848 0.815 0.772 0.721

1 3.340

40 80 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.165 0.277 0.338 0.455 0.635 0.909

3.010 2.786 2.664 2.431 2.070 1.521

7.114 6.095 5.573 4.638 3.367 1.818

1.647 2.664 3.186 4.122 5.392 6.940

0.105 0.105 0.105 0.105 0.105 0.105

0.094 0.088 0.084 0.077 0.065 0.048

1.292 2.089 2.498 3.232 4.232 5.445

2.003 2.698 3.055 3.695 4.568 5.627

2.081 3.151 3.638 4.395 5.211 5.848

1.245 1.886 2.178 2.632 3.118 3.502

1.125 1.087 1.069 1.034 0.983 0.917

1 1/2 4.826

40 80 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.165 0.277 0.368 0.508 0.714 1.016

4.496 4.272 4.089 3.810 3.399 2.794

15.873 14.332 13.132 11.397 9.069 6.128

2.419 3.954 5.154 6.889 9.217 12.160

0.151 0.151 0.151 0.151 0.151 0.151

0.141 0.134 0.128 0.120 0.107 0.088

1.896 3.102 4.044 5.403 7.230 9.535

3.484 4.533 5.356 6.541 8.135 10.148

6.579 10.277 12.903 16.275 20.104 23.642

2.725 4.259 5.342 6.751 8.325 9.800

1.648 1.610 1.582 1.537 1.476 1.394

2 6.033

40 80 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.165 0.277 0.391 0.554 0.871 1.107

5.70 5.48 5.25 4.93 4.29 3.82

25.54 23.54 21.67 19.05 14.45 11.44

3.044 5.005 6.934 9.527 14.13 17.13

0.190 0.190 0.190 0.190 0.190 0.190

0.179 0.172 0.165 0.155 0.135 0.120

2.387 3.925 5.436 7.473 11.08 13.44

4.94 6.28 7.60 9.38 12.52 14.58

13.11 20.77 27.72 36.13 48.41 54.61

4.346 6.883 9.193 11.979 16.043 18.091

2.075 2.037 1.999 1.945 1.852 1.786

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS AND PARTICULARS OF LINE PIPE Doc. No : 30101-30-17D-200 C:\webpage\piping_std\30101-30-17D-200.docdoc

BAA Checked

Approved

SHT. 1 OF 5

REV. 0

DIMENSIONS AND PARTICULARS OF LINE PIPE Nom. pipe size inch OD cm

A

B

C

cm

cm

cm2

cm2

m2/m

m2/m

Kg/m

Weight Filled with water Kg/m

3 8.890

40 80 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.211 0.305 0.549 0.762 1.110 1.524

8.47 8.28 7.79 7.37 6.67 5.84

56.31 53.86 47.67 42.58 34.96 26.77

5.74 8.21 14.37 19.47 27.15 35.28

0.279 0.279 0.279 0.279 0.279 0.279

0.266 0.260 0.245 0.231 0.209 0.183

4.51 6.44 11.28 15.25 21.31 27.65

10.13 11.81 16.04 19.51 24.80 30.33

54.15 75.84 125.70 162.33 209.36 249.32

12.19 17.06 28.25 36.48 47.13 49.82

3.068 3.038 2.957 2.885 2.779 2.659

4 11.430

40 80 120 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.211 0.305 0.602 0.856 1.110 1.349 1.712

11.01 10.82 10.23 9.72 9.21 8.73 8.01

95.14 91.91 82.11 74.18 66.63 59.86 50.31

7.43 10.64 20.44 28.44 35.99 42.58 52.24

0.359 0.359 0.359 0.359 0.359 0.359 0.359

0.346 0.340 0.321 0.305 0.289 0.274 0.251

5.83 8.35 16.06 22.29 28.21 33.49 40.98

15.35 17.53 24.26 29.70 34.88 39.47 46.01

117.0 164.83 300.93 400 484.91 552.34 636.24

20.47 28.87 52.60 69.97 84.88 96.68 111.27

3.967 3.934 3.835 3.752 3.670 3.597 3.490

6 16.828

40 80 120 160 -

Std XS XXS

5S 10 S 40 S 80S -

0.277 0.340 0.711 1.097 1.427 1.824 2.195

16.27 16.15 15.41 14.63 13.97 13.18 12.44

207.69 204.47 186.34 168.15 153.32 136.42 121.45

14.39 17.62 35.99 54.18 69.01 85.97 100.87

0.529 0.529 0.529 0.529 0.529 0.529 0.529

0.511 0.507 0.484 0.460 0.439 0.414 0.391

7.99 13.82 28.23 42.51 54.15 67.41 79.10

28.79 34.27 46.84 59.31 69.48 81.04 91.26

493 599 1171 1686 2065 2456 2760

58.67 71.28 139.29 200.41 245.48 291.85 328.23

5.852 5.829 5.702 5.575 5.469 5.344 5.232

8 21.908

20 30 40 60 80 100 120 140 160

Std XS XXS -

5S 10 S 40 S 80S -

0.277 0.376 0.635 0.704 0.818 1.031 1.270 1.506 1.824 2.062 2.223 2.301

21.35 21.16 20.64 20.50 20.27 19.85 19.37 18.90 18.26 17.78 17.46 17.31

357.98 351.53 334.11 330.24 322.50 308.96 294.77 280.58 261.87 248.33 239.30 235.43

18.80 25.41 42.44 46.82 54.18 67.59 82.30 96.49 115.06 128.54 137.38 141.70

0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688

0.671 0.664 0.648 0.644 0.637 0.623 0.608 0.594 0.574 0.559 0.549 0.544

14.75 19.94 33.27 36.75 42.48 53.03 64.56 75.69 90.22 100.83 107.76 111.14

50.57 55.04 66.72 69.75 74.75 83.97 94.02 103.72 116.41 125.66 131.70 134.65

1101 1473 2402 2639 3018 3696 4400 5053 5852 6402 6743 6905

100.45 134.54 219.42 240.73 275.47 337.24 401.81 461.13 534.22 585.02 616.15 630.90

7.645 7.620 7.532 7.501 7.463 7.389 7.310 7.231 7.130 7.054 7.003 6.980

10 27.305

20 30 40 60 80 100 120 140 160

Std XS -

5S 10 S 40 S 80S -

0.340 0.419 0.635 0.709 0.780 0.927 1.270 1.506 1.824 2.141 2.540 2.858

26.62 26.47 26.04 25.89 25.75 25.45 24.77 24.29 23.66 23.02 22.23 21.59

556.64 550.19 532.13 526.32 520.52 508.91 481.82 463.11 439.25 416.03 387.65 365.72

29.15 35.41 53.27 59.21 64.95 76.82 103.84 122.03 145.96 169.24 197.37 219.30

0.858 0.858 0.858 0.858 0.858 0.858 0.858 0.858 0.858 0.858 0.858 0.858

0.826 0.831 0.818 0.813 0.809 0.799 0.778 0.763 0.743 0.723 0.698 0.678

22.54 27.83 41.72 46.43 50.95 60.23 81.45 95.72 114.47 132.73 154.05 172.09

78 83 95 99 103 111 130 142 158 174 194 207

2651 3201 4733 5240 5723 6693 8824 10193 11913 13486 15317 16608

194 234 347 384 419 490 646 747 872 988 1121 1218

9.525 9.499 9.423 9.398 9.373 9.322 9.220 9.144 9.042 8.941 8.814 8.712

0 Rev.

Schedule Numbers Note 1

01/2002 Date

Wall Thickn.

Inside Dia.

Inside Area

Metal Area

Outside Surface

Inside Surface

Weight Note 2

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS AND PARTICULARS OF LINE PIPE Doc. No : 30101-30-17D-200 C:\webpage\piping_std\30101-30-17D-200.docdoc

Moment of inertia

Section modules

Radius of gyration

cm4

cm3

cm

BAA Checked

Approved

SHT. 2 OF 5

REV. 0

DIMENSIONS AND PARTICULARS OF LINE PIPE Nom. pipe size inch OD cm

A

B

C

cm

cm

cm2

cm2

m2/m

m2/m

Kg/m

Weight Filled with water Kg/m

12 32.385

20 30 40 60 80 100 120 140 160

Std XS -

5S 10 S 40 S 80S -

0.419 0.457 0.635 0.838 0.953 1.031 1.270 1.427 1.745 2.141 2.540 2.858 3.332

31.55 31.47 31.12 30.71 30.48 30.32 29.85 29.53 28.90 28.10 27.31 26.67 25.72

781.74 777.87 760.46 740.46 729.50 721.76 699.18 684.99 655.32 619.85 585.66 558.57 519.23

42.05 45.86 63.46 83.07 94.04 101.52 124.09 138.80 167.95 200.27 238.00 265.09 303.79

1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018 1.018

0.991 0.988 0.978 0.966 0.957 0.954 0.939 0.927 0.908 0.883 0.858 0.838 0.808

29.11 36.01 49.67 65.13 73.75 79.65 97.34 108.86 131.70 159.51 186.73 207.84 238.48

107 114 126 139 147 152 167 178 197 221 245 264 291

5378 5048 7987 10343 11625 12487 15068 16691 19771 23392 26722 29178 32058

332 361 493 639 718 772 929 1029 1221 1444 1650 1801 2009

11.300 11.270 11.220 11.151 11.125 11.100 10.998 10.947 10.846 10.719 10.592 10.490 10.338

14 35.560

10 20 30 40 60 80 100 120 140 160

Std XS -

-

0.635 0.792 0.953 1.110 1.270 1.427 1.506 1.588 1.745 1.905 2.223 2.380 2.776 3.175 3.571

34.29 33.98 33.66 33.34 33.02 32.71 32.55 32.39 32.07 31.75 31.12 30.80 30.01 29.21 28.42

923.00 906.23 889.46 872.69 855.92 839.79 832.05 823.66 807.54 791.42 760.46 744.98 706.92 670.16 634.04

69.66 86.55 103.52 120.09 136.80 153.05 161.12 169.37 185.30 201.24 232.84 248.32 285.73 323.14 358.62

1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119 1.119

1.076 1.067 1.058 1.048 1.036 1.027 1.021 1.018 1.009 0.997 0.978 0.966 0.942 0.917 0.893

54.62 67.97 81.20 94.29 107.27 120.02 126.35 132.85 145.35 157.92 182.52 194.53 224.20 253.29 281.41

147 159 170 182 193 204 210 215 226 237 259 269 295 320 345

10631 13070 15525 17856 20146 22352 23392 24516 26555 28595 32508 34339 38709 42331 46909

598 736 873 1003 1132 1257 1316 1378 1494 1609 1827 1930 2176 2406 2615

12.344 12.294 12.243 12.192 12.141 12.090 12.040 12.014 11.963 11.913 11.811 11.760 11.633 11.506 11.379

16 40.640

10 20 30 40 60 80 100 120 140 160

Std XS -

-

0.635 0.792 0.953 1.110 1.270 1.427 1.588 1.666 1.745 1.905 2.141 2.223 2.619 3.094 3.650 4.046

39.37 39.06 38.74 38.42 38.10 37.79 37.47 37.31 37.15 36.83 36.36 36.20 35.40 34.45 33.34 32.55

1217 1197 1177 1159 1139 1121 1102 1092 1083 1064 1037 1028 984 932 872 832

79.78 99.20 118.74 137.83 157.05 175.82 194.79 203.82 212.85 231.55 258.64 268.32 312.82 365.07 423.76 465.04

1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277 1.277

1.237 1.228 1.216 1.207 1.198 1.186 1.176 1.173 1.167 1.158 1.143 1.137 1.112 1.082 1.048 1.021

62.57 77.91 93.12 108.09 123.16 137.88 152.71 159.96 167.19 181.76 203.05 210.33 245.27 286.13 332.57 364.72

184 198 211 224 237 250 263 269 275 288 307 313 344 397 420 448

15983 19688 23392 26972 30468 33839 37211 38834 40416 43579 48158 49056 56015 64765 73256 78834

787 970 1152 1326 1499 1749 1839 1911 1989 2145 2370 2525 2796 3187 3605 3879

14.148 14.097 14.046 13.970 13.919 13.868 13.818 13.792 13.767 13.716 13.640 13.614 13.462 13.310 13.123 13.005

0 Rev.

Schedule Numbers Note 1

01/2002 Date

Wall Thickn.

Inside Dia.

Inside Area

Metal Area

Outside Surface

Inside Surface

Weight Note 2

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS AND PARTICULARS OF LINE PIPE Doc. No : 30101-30-17D-200 C:\webpage\piping_std\30101-30-17D-200.docdoc

Moment of inertia

Section modules

Radius of gyration

cm4

cm3

cm

BAA Checked

Approved

SHT. 3 OF 5

REV. 0

DIMENSIONS AND PARTICULARS OF LINE PIPE Nom. pipe size inch OD cm

A

B

C

cm

cm

cm2

cm2

m2/m

m2/m

Kg/m

Weight Filled with water Kg/m

18 45.720

10 20 30 40 60 80 100 120 140 160

Std XS -

-

0.635 0.792 0.953 1.110 1.270 1.427 1.588 1.745 1.905 2.223 2.380 2.936 3.493 3.967 4.524

44.45 44.14 43.82 43.50 43.18 42.87 42.55 42.23 41.91 41.28 40.96 39.85 38.74 37.79 36.67

1551 1529 1507 1486 1464 1442 1422 1399 1379 1337 1317 1246 1177 1121 1055

89.91 111.84 133.90 155.51 177.31 198.66 219.94 241.23 261.87 303.79 323.79 394.74 463.11 520.21 585.01

1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436 1.436

1.396 1.387 1.378 1.365 1.356 1.347 1.338 1.326 1.317 1.295 1.286 1.253 1.216 1.186 1.152

70.52 87.84 105.04 122.11 139.05 155.87 172.58 189.02 205.60 238.14 254.0 309.44 363.28 408.05 459.06

226 241 256 271 285 300 315 329 344 372 386 434 479 520 565

22851 28220 33590 38751 43829 48782 53652 58397 63059 72049 76337 90738 104016 114463 125701

1000 1237 1468 1694 1917 2134 2348 2561 2758 3159 3340 3969 4549 5014 5506

15.951 15.875 15.824 15.773 15.723 15.672 15.621 15.570 15.494 15.392 15.342 15.164 14.986 14.834 14.656

20 50.800

10 20 30 40 60 80 100 120 140 160

Std XS -

-

0.635 0.792 0.953 1.110 1.270 1.427 1.506 1.588 1.745 1.905 2.062 2.223 2.619 3.254 3.810 4.445 4.999

49.53 49.22 48.90 48.58 48.26 47.95 47.79 47.63 47.31 46.99 46.68 46.36 45.56 44.29 43.18 41.91 40.80

1925 1902 1876 1853 1828 1804 1793 1780 1757 1733 1710 1687 1629 1540 1464 1379 1307

100.04 124.48 149.12 173.24 197.37 221.23 233.49 245.10 268.96 292.83 315.40 339.27 396.03 485.68 562.44 646.93 719.17

1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597 1.597

1.557 1.545 1.536 1.527 1.515 1.506 1.503 1.497 1.487 1.475 1.466 1.457 1.433 1.393 1.356 1.317 1.283

78.46 97.32 116.96 135.87 154.95 173.60 182.89 192.44 210.86 229.45 247.60 265.95 310.80 381.08 441 507.56 563.97

271 288 304 321 338 354 362 371 387 403 419 435 474 535 587 645 695

31509 38918 46368 53527 60645 67596 70926 74380 80998 87616 93943 100270 115379 138188 156502 175649 191050

1240 1532 1826 2107 2388 2661 2792 2928 3189 3449 3699 3948 4542 5440 6062 6915 7522

17.729 17.678 17.628 17.577 17.526 17.475 17.424 17.399 17.348 17.297 17.247 17.196 17.069 16.840 16.662 16.459 16.281

24 60.960

10 20 30 40 60 80 100 120 140 160

Std XS --

-

0.635 0.792 0.953 1.110 1.270 1.427 1.588 1.745 1.905 2.459 3.094 3.889 4.602 5.237 5.951

59.69 59.38 59.06 58.74 58.42 58.11 57.79 57.47 57.15 56.04 54.77 53.18 51.76 50.49 49.06

2799 2773 2741 2709 2676 2650 2618 2592 2567 2463 2354 2218 2102 1999 1889

120.29 149.64 179.50 208.98 238.00 267.03 296.05 324.43 353.46 451.50 562.44 697.24 814.63 916.54 1028.13

1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914 1.914

1.874 1.865 1.856 1.844 1.835 1.826 1.817 1.804 1.795 1.762 1.722 1.670 1.625 1.585 1.542

94.35 117.45 140.79 163.64 186.73 209.51 232.17 254.70 277.13 354.31 440.98 546.69 638.93 718.90 806.41

374 394 414 435 455 475 494 514 534 601 677 769 849 919 995

54776 67804 80873 93485 106139 118209 130696 142351 154421 193547 236002 285118 325908 359206 393754

1796 2225 2653 3071 3482 3884 4284 4674 5064 6358 7751 9357 10684 11782 12913

21.336 21.285 21.209 21.158 21.107 21.057 21.005 20.955 20.879 20.726 20.498 20.218 19.990 19.787 19.558

0 Rev.

Schedule Numbers Note 1

01/2002 Date

Wall Thickn.

Inside Dia.

Inside Area

Metal Area

Outside Surface

Inside Surface

Weight Note 2

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS AND PARTICULARS OF LINE PIPE Doc. No : 30101-30-17D-200 C:\webpage\piping_std\30101-30-17D-200.docdoc

Moment of inertia

Section modules

Radius of gyration

cm4

cm3

cm

BAA Checked

Approved

SHT. 4 OF 5

REV. 0

DIMENSIONS AND PARTICULARS OF LINE PIPE Nom. pipe size inch

Schedule Numbers Note 1

OD cm 30 76.200

Wall Thickn.

Inside Dia.

Inside Area

Metal Area

Outside Surface

Inside Surface

Weight Note 2

A

B

C

cm

cm

cm2

cm2

m2/m

m2/m

Kg/m

Weight Filled with water Kg/m

10 20 30

-

-

0.792 1.270 1.588

74.62 73.66 73.03

4373 4263 4186

187.69 298.63 371.52

2.393 2.393 2.393

2.344 2.313 2.295

147.21 234.40 291.77

584 660 711

Moment Section Radius of Modules of inertia gyration cm4

cm3

cm

133610 209780 258895

3507 5506 6801

26.670 26.492 26.391

Note:

0 Rev.

1

Column A : ASA B 36.10 steel pipe schedule numbers. Column B : ASA B 36.10 steel pipe nominal wall designation. Column C : ASA B 36.19 stainless steel pipe schedule numbers (5S is not an approved standard).

2

Specified weights are based on weights for mild steel pipes. For ferritic stainless steel pipes the values are 5% less. For austenitic stainless steel pipes the values are 2% greater.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS AND PARTICULARS OF LINE PIPE Doc. No : 30101-30-17D-200 C:\webpage\piping_std\30101-30-17D-200.docdoc

BAA Checked

Approved

SHT. 5 OF 5

REV. 0

O.D. 1” 1 1/2” 2’ Class 3’ 150 4” Flg. 6” 8” 10” 12” 14” 16” 18” 20” 24” 1” 1 1/2” 2’ Class 3’ 300 4” Flg. 6” 8” 10” 12” 14” 16” 18” 20” 24” 1” 1 1/2” 2’ Class 3’ 600 4” Flg 6” 8” 10” 12” 14” 16” 18” 20” 24” O.D.

1” 100 110 120 140 160 185 215 245 285 310 345 360 395 450 105 120 125 150 170 205 235 265 305 335 370 400 430 500 105 120 125 150 180 220 255 300 325 345 385 415 450 515 1”

1 1/2” 105 115 130 145 165 190 225 255 295 320 350 370 400 460 115 130 135 155 180 210 240 275 310 345 375 405 440 510 115 130 135 155 190 230 260 305 330 355 395 425 460 520 1 1/2”

2” 110 120 135 155 170 195 230 260 300 325 355 375 405 465 120 135 140 160 185 215 250 280 320 350 380 415 445 515 120 135 140 160 195 235 265 310 335 360 400 430 465 525 2”

3” 125 135 150 165 185 210 245 275 315 340 370 390 420 480 135 150 155 175 200 230 260 295 330 365 395 425 460 530 135 150 155 175 210 250 280 325 350 375 415 445 480 540 3”

4” 140 150 160 180 200 225 255 290 325 350 385 400 435 490 145 160 165 190 210 245 275 305 345 375 410 440 470 540 145 160 165 190 220 260 295 340 365 385 425 455 490 555 4”

6” 165 175 190 205 225 250 285 315 355 380 410 430 460 520 175 190 195 215 240 270 300 335 370 405 435 465 500 570 175 190 195 215 250 290 320 365 390 415 455 485 520 580 6”

PIPE 8” 190 200 215 230 250 275 310 340 380 405 435 455 485 545 200 215 220 240 265 295 325 360 395 430 460 490 525 595 200 215 220 240 275 315 345 390 415 440 480 510 545 605 8”

10” 220 225 240 260 280 305 335 365 405 430 460 480 515 570 225 240 245 270 290 325 355 385 425 455 490 520 550 620 225 240 245 270 300 340 375 420 445 465 505 535 570 635 10”

12” 245 255 265 285 305 330 360 390 430 455 490 505 540 595 250 265 270 295 315 350 380 410 450 480 515 545 575 645 250 265 270 295 325 365 400 445 470 490 530 560 595 660 12”

14” 260 270 280 300 320 345 375 410 445 470 505 525 555 610 265 285 290 310 330 365 395 430 465 495 530 560 595 660 265 285 290 310 340 385 415 460 485 505 550 575 610 675 14”

16” 285 295 305 325 345 370 400 435 470 495 530 550 580 635 290 310 315 335 355 390 420 455 490 520 555 585 620 685 290 310 315 335 365 410 440 485 510 530 575 600 635 700 16”

18” 310 320 330 350 370 395 425 460 495 520 555 575 605 660 320 335 340 360 385 415 445 480 515 550 580 610 645 715 320 335 340 360 390 435 465 510 535 555 600 625 660 725 18”

20” 335 345 355 375 395 420 455 485 525 550 580 600 630 690 345 360 365 385 410 440 470 505 540 575 605 635 670 740 345 360 365 385 420 460 490 535 560 585 625 655 690 750 20”

24” 385 395 410 430 445 470 505 535 575 600 630 650 680 740 395 410 415 435 460 490 525 555 595 625 655 690 720 790 395 410 415 435 470 510 540 585 610 635 675 705 740 800 24”

Notes: 1 Insulation thickness to be added and check insulated lines on use of insulated flanges. 2 Dimensions based on staggered flanges, allow side movement due to expansion. 3 Dimensions based on minimum distance of 25 mm between flange and pipe and 50 mm between flange and structure column or wall. 0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK MIN. PIPE SPACING WITH ANSI FLANGES Doc. No : 30101-30-17D-201 C:\webpage\piping_std\30101-30-17D-201.docdoc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

B+H+1.5T T

T

B

H

H A

A+H+1.5T T

T

B+1.5(T1 + T2) T2

T1

T1 H

H A= H + 1.5 T

A+1.5 (T1 + T2)

B+H+1.5 T

BASIC SPACING ‘A’

BASIC SPACING ‘B’

lin e s ize 2 3 4 6 8 10 12 14 16 18 20 24

2 178 203 229 305 356 432 483 533 584 660 711 838

3 178 203 229 305 356 432 483 533 584 660 711 838

4 178 203 254 305 381 432 508 533 610 660 711 838

6 203 229 254 330 381 457 508 533 610 660 737 864

B a s ic S p a c in g 'A' 8 10 12 14 203 203 229 229 229 254 254 254 280 280 280 305 330 356 356 356 381 406 406 432 457 483 483 483 508 533 533 559 559 559 584 584 610 635 635 660 686 686 711 711 737 762 762 762 864 864 889 889

16 229 280 305 381 432 508 559 610 660 711 787 914

18 254 280 305 381 432 508 559 610 660 737 787 914

20 254 305 330 381 457 508 584 610 686 737 813 914

24 280 305 356 406 483 533 610 635 711 762 813 940

lin e s ize 2 3 4 6 8 10 12 14 16 18 20 24

2 178 178 178 203 203 203 229 229 229 254 254 280

3 203 203 203 229 229 254 254 254 280 280 305 305

4 229 229 254 254 280 280 280 305 305 305 330 356

6 305 305 305 330 330 356 356 356 381 381 381 406

B a s ic S p a c in g 'B ' 8 10 12 14 356 432 482 533 356 432 482 533 381 432 508 533 381 457 508 559 381 457 508 559 406 483 533 559 406 483 533 584 432 483 558 584 432 508 558 610 432 508 558 610 457 508 584 610 483 533 610 635

16 584 584 610 610 610 635 635 660 660 660 686 711

18 660 660 660 660 686 686 711 711 711 737 737 762

20 711 711 711 737 737 762 762 762 787 787 813 813

24 838 838 838 864 864 864 889 889 914 914 914 940

Notes: 1. Spacing shown in the diagrams allow 50 to 70 mm clearance. 2. The dimensions ‘H’ is the effective shoe height and ‘T’ the thickness of insulation. 3. The factor 1.5 has been substituted for the factor √ 2= 1.141

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK MIN. PIPE SPACING FOR 45º TAKE-OFF Doc. No : 30101-30-17D-202 C:\webpage\piping_std\30101-30-17D-202.docdoc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

T2

Socket Weld Fittings ( 1 ) A

B

Class

Class

SW Unions (2) C

E

F

G

H

J

Swg (3) NIP K

L

Socket Weld Flanges M

Class

NPS 3000 6000 9000 3000 6000 9000

N

O

P

M

Class

3000

N

O

P

95

10

Class

150

300

1/2

14

18

24

10

11

14

10

6

21

29

49

10

70

100

6

16

89

10

12

22

3/4

18

21

27

11

13

17

13

6

22

31

57

13

76

100

5

16

98

11

14

25 117 11

1

20

25

30

12

15

19

13

9

27

36

62

13

89

100

4

17 108 13

14

27 124 13

1 1/2

30

36

36

19

23

23

13

9

30

41

77

13

114

100

6

22 127 16

14

30 156 16

2

36

37

52

23

27

26

16

15

39

54

86

16

165

100

7

25 152 18

15

33 165 18

2 1/2

39

27

16

14

40

70

102

16

178

100 10

29 178 19

19

38 191 19

3

55

29

16

14

42

77

109

16

203

100 42

59

22

43 210 21

4

64

39

16

14

45

229

100

Screwed Fittings

(1)

A

B

Class

Class

Scr Unions (2) C

E

F

G

H

J

Swg (3) NIP K

L

21

Screwed flanges M

Class

NPS 2000 3000 6000 2000 3000 6000

71

N

O

P

M

Class

3000

N

O

P

95

16

Class

150

300

1/2

18

22

27

11

14

18

11

26

13

17

49

16

70

100

16

89

16

6

22

3/4

20

25

31

12

16

20

13

25

13

25

57

16

76

100

16

98

16

9

25 117 16

1

23

29

36

14

18

20

15

30

15

28

62

17

89

100

17 108 17

9

27 124 18

1 1/2

33

42

46

17

25

26

18

43

22

22

76

22

114

100

22 127 22

8

30 156 22

2

41

45

64

24

26

33

19

48

24

36

86

25

165

100

25 152 25

5

33 165 28

2 1/2

42

59

71

28

28

40

24

44

22

44

102

29

178

100

29 178 29

6

38 191 32

3

60

69

80

38

38

53

26

56

28

49

109

30

203

100

30 191 30

11

43 210 32

4

78

86

86

51

51

51

28

65

33

229

100

33 229 33

11

48 254 37

Note: 1. Based on minimum dimensions per ANSI B 16.11 2. Based on minimum dimensions per MSS SP 83 3. Based on minimum dimensions per MSS SP 95 4. Based on ANSI B 16.5

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK BUILT-UP DIM. SMALL BORE FITTINGS Doc. No : 30101-30-17D-203 C:\webpage\piping_std\30101-30-17D-203.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK SMALL BORE FITTINGS AND VALVES Doc. No : 30101-30-17D-204 C:\webpage\piping_std\30101-30-17D-204.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Dimensions according toANSI B 16.9 Nominal Pipe Size 1/2 x 1/2 x 3/8 1/2 x 1/2 x 1/4 3/4 x 3/4 x 1/2 3/4 x 3/4 x 3/8

Centre to end Run Outlet C M 25 25 25 25 29 29

29 29

1 x 1 x 3/4 1 x 1 x 1/2

38 38

38 38

11/2 x 11/2 x 11/4 11/2 x 11/2 x 1 11/2 x 11/2 x 3/4 11/2 x 11/2 x 1/2

57 57 57 57

57 57 57 57

2 x 2 x 11/2 2 x 2 x 11/4 2x2x1 2 x 2 x 3/4

64 64 64 64

60 57 51 44

21/2 x 21/2 x 2 21/2 x 21/2 x 11/2 21/2 x 21/2 x 11/4 21/2 x 21/2 x 1

76 76 76 76

70 67 64 57

3 x 3 x 21/2 3x3x2 3 x 3 x 11/2 3 x 3 x 11/4

86 86 86 86

83 76 73 70

31/2 x 31/2 x 3 31/2 x 31/2 x 21/2 31/2 x 31/2 x 2 31/2 x 31/2 x 11/2

95 95 95 95

92 89 83 79

4 x 4 x 31/2 4x4x3 4 x 4 x 21/2 4x4x2 4 x 4 x 11/2

105 105 105 105 105

102 98 95 89 86

5x5x4 5 x 5 x 3 1/2 5x5x3 5 x 5 x 2 1/2 5x5x2

124 124 124 124 124

117 114 111 108 105

6x6x5 6x6x4 6 x 6 x 31/2 6 x 6 x 31/2 6 x 6 x 21/2

143 143 143 143 143

137 130 127 124 121

8x8x6 8x8x5 8x8x4 8 x 8 x 31/2

178 178 178 178

168 162 155 152

10 x 10 x 8 10 x 10 x 6 10 x 10 x 5 10 x 10 x 4

216 216 216 216

203 194 191 184

0 Rev.

01/2002 Date

Nominal Pipe Size 12 x 12 x 10 12 x 12 x 8 12 x 12 x 6 12 x 12 x 5

Centre to end Run Outlet C M 254 241 254 229 254 219 254 216

14 x 14 x 12 14 x 14 x 10 14 x 14 x 8 14 x 14 x 6

279 279 279 279

270 257 248 238

16 x 16 x 14 16 x 16 x 12 16 x 16 x 10 16 x 16 x 8 16 x 16 x 6

305 305 305 305 305

305 295 283 273 264

18 x 18 x 16 18 x 18 x 14 18 x 18 x 12 18 x 18 x 10 18 x 18 x 8

343 343 343 343 343

330 330 321 308 298

20 x 20 x 18 20 x 20 x 16 20 x 20 x 14 20 x 20 x 12 20 x 20 x 10 20 x 20 x 8

381 381 381 381 381 381

368 356 356 346 333 324

22 x 22 x 20 22 x 22 x 18 22 x 22 x 16 22 x 22 x 14 22 x 22 x 12 22 x 22 x 10

419 419 419 419 419 419

406 394 381 381 371 359

24 x 24 x 22 24 x 24 x 20 24 x 24 x 18 24 x 24 x 16 24 x 24 x 14 24 x 24 x 12 24 x 24 x 10

432 432 432 432 432 432 432

432 432 419 406 406 397 384

26 x 26 x 24 26 x 26 x 22 26 x 26 x 20 26 x 26 x 18 26 x 26 x 16 26 x 26 x 14 26 x 26 x 12

495 495 495 495 495 495 495

483 470 457 444 432 432 422

28 x28 x 26 28 x28 x 24 28 x28 x 22 28 x28 x 20 28 x28 x 18 28 x28 x 16 28 x28 x 14 28 x28 x 12

521 521 521 521 521 521 521 521

521 508 495 483 470 457 457 448

Nominal Pipe Size 30 x 30 x 28 30 x 30 x 26 30 x 30 x 24 30 x 30 x 22 30 x 30 x 20 30 x 30 x 18 30 x 30 x 16 30 x 30 x 14 30 x 30 x 12 30 x 30 x 10

Centre to end Run Outlet C M 559 546 559 546 559 533 559 521 559 508 559 495 559 483 559 483 559 473 559 460

32 x 32 x 30 32 x 32 x 28 32 x 32 x 26 32 x 32 x 24 32 x 32 x 22 32 x 32 x 20 32 x 32 x 18 32 x 32 x 16 32 x 32 x 14

597 597 597 597 597 597 597 597 597

584 572 572 559 546 533 521 508 508

34 x 34 x 32 34 x 34 x 30 34 x 34 x 28 34 x 34 x 26 34 x 34 x 24 34 x 34 x 22 34 x 34 x 20 34 x 34 x 18 34 x 34 x 16

635 635 635 635 635 635 635 635 635

622 610 597 597 584 572 559 546 533

36 x 36 x 34 36 x 36 x 32 36 x 36 x 30 36 x 36 x 28 36 x 36 x 26 36 x 36 x 24 36 x 36 x 22 36 x 36 x 20 36 x 36 x 18 36 x 36 x 16

673 673 673 673 673 673 673 673 673 673

660 648 635 622 622 610 597 584 572 559

38 x 38 x 36 38 x 38 x 34 38 x 38 x 32 38 x 38 x 30 38 x 38 x 28 38 x 38 x 26 38 x 38 x 24 38 x 38 x 22 38 x 38 x 20 38 x 38 x 18

711 711 711 711 711 711 711 711 711 711

711 698 686 673 648 648 635 622 610 597

40 x 40 x 38 40 x 40 x 36 40 x 40 x 34 40 x 40 x 32 40 x 40 x 30 40 x 40 x 28 40 x 40 x 26 40 x 40 x 24

749 749 749 749 749 749 749 749

749 737 724 711 698 673 673 660

First Issue Description

Nominal Pipe Size 40 x 40 x 22 40 x 40 x 20 40 x 40 x 18 42 x 42 x 40 42 x 42 x 38 42 x 42 x 36 42 x 42 x 34 42 x 42 x 32 42 x 42 x 30 42 x 42 x 28 42 x 42 x 26 42 x 42 x 24 42 x 42 x 22 42 x 42 x 20 42 x 42 x 18 42 x 42 x 16

762 762 762 762 762 762 762 762 762 762 762 762 762

711 711 711 711 711 711 698 698 660 660 660 648 648

44 x 44 x 42 44 x 44 x 40 44 x 44 x 38 44 x 44 x 36 44 x 44 x 34 44 x 44 x 32 44 x 44 x 30 44 x 44 x 28 44 x 44 x 26 44 x 44 x 24 44 x 44 x 22 44 x 44 x 20

813 813 813 813 813 813 813 813 813 813 813 813

762 749 737 724 724 711 711 698 698 698 686 686

46 x 46 x 44 46 x 46 x 42 46 x 46 x 40 46 x 46 x 38 46 x 46 x 36 46 x 46 x 34 46 x 46 x 32 46 x 46 x 30 46 x 46 x 28 46 x 46 x 26 46 x 46 x 24 46 x 46 x 22

851 851 851 851 851 851 851 851 851 851 851 851

800 787 775 762 762 749 749 737 737 737 724 724

48 x 48 x 46 48 x 48 x 44 48 x 48 x 42 48 x 48 x 40 48 x 48 x 38 48 x 48 x 36 48 x 48 x 34 48 x 48 x 32 48 x 48 x 30 48 x 48 x 28 48 x 48 x 26 48 x 48 x 24 48 x 48 x 22

889 889 889 889 889 889 889 889 889 889 889 889 889

838 838 813 813 813 787 787 787 762 762 762 737 737

LEA Prepared

PIPING HANDBOOK DIMENSIONS REDUCING TEES Doc. No : 30101-30-17D-205 C:\webpage\piping_std\30101-30-17D-205.doc

Centre to end Run Outlet C M 749 648 749 635 749 622

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

All dimensions based on LR elbow Nom Size 2 3 4 6 8 10 12 14 16 18 20 22 24 26 30 34 36 42

0 Rev.

01/2002 Date

15 10 15 20,1 30,1 40,1 50,2 60,2 70,2 80,3 90,3 100,4 110,4 120,4 130,5 150,5 170,6 180,6 210,7

20 13,4 20,2 26,9 40,3 53,7 67,2 80,6 94 107,5 120,9 134,3 147,8 161,2 174,6 201,5 228,4 241,8 282,1

Dimension K by angle B 30 40 50 20,4 27,7 35,5 30,6 41,6 53,3 40,8 55,5 71,1 61,2 83,2 106,6 81,7 110,9 142,1 102,1 138,7 177,7 122,5 166,4 213,2 142,9 194,2 248,7 163,3 221,9 284,3 183,7 249,6 319,8 204,1 277,4 355,3 224,6 305,1 390,9 245 332,8 426,4 265,4 360,6 461,9 306,2 416,1 533 347 471,5 604 367,5 499,3 639,6 428,7 582,5 746,2

First Issue Description

60 44 66 88 132 176 220 264 308 352 396 440 484 528 572 660 748 792 924

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF PARTS OF ELBOWS Doc. No : 30101-30-17D-206 C:\webpage\piping_std\30101-30-17D-206.docdoc

75 58,5 87,7 116,9 175,4 233,9 292,3 350,8 409,3 467,7 526,2 584,7 643,2 701,6 760,1 877 994 1052,4 1227,8

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

Example

Nom Size 2 3 4 6 8 10 12 14 16 18 20 22 24 26 30 34 36 42

2” Pipe & = 100 Outside arc = 10 x A at 10 At & = 10 for 2” pipe = 10 x 1,856 = 18,56 mm Inside arc = 10 x B at 10 = 10 x 0,802 = 8,02 mm

0 Rev.

01/2002 Date

Outside Arc A 0 AT & = 1 1,855 2,769 3,655 5,456 7,228 9,028 10,8 12,406 14,179 15,951 17,724 19,496 21,268 23,041 26,585 30,13 31,902 37,219

First Issue Description

Inside Arc B 0 AT & = 1 0,803 1,218 1,662 2,52 3,406 4,265 5,151 6,203 7,089 7,976 8,862 9,748 10,634 11,52 13,293 15,065 15,951 18,61

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF PARTS OF ELBOWS Doc. No : 30101-30-17D-206 C:\webpage\piping_std\30101-30-17D-206.docdoc

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

Nom Size 2 3 4 6 8 10 12 14 16 18 20 24

0 Rev.

01/2002 Date

A 228 331 432 635 839 1067 1270

R = 3D B 139 196 254 368 482 621 735

C 76 102 127 178 229 305 356

R 152 229 305 457 610 762 914

A 330 483 635 940 1245 1575 1880 2184 2489 2794 3100 3710

R = 5D B 181 260 338 494 650 831 987 1142 1299 1454 1612 1923

First Issue Description

C 76 102 127 178 229 305 356 406 457 508 560 660

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF BENDS R=3D/R=5D Doc. No : 30101-30-17D-207 C:\webpage\piping_std\30101-30-17D-207.doc

R 254 381 508 762 1016 1270 1524 1778 2032 2286 2540 3050

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

CLASS 150 # Nom Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 221) 24 261) 301) 341) 361)

Dimensions as per ANSI B 16.5

O

Q

R

X

Y

Z

B

r

N

D

89 98 108 117 127 152 178 191 216 229 254 279 343 406 483 533 597 635 699 749 813 870 964 1111 1168

11 13 14 16 17 19 22 24 24 24 24 25 29 30 32 35 37 40 43 46 48 51 54 59 60

35 43 51 64 73 92 105 127 140 157 186 216 270 324 381 413 470 533 584 641 692 743 857 959 1022

48 52 56 57 62 64 70 70 71 76 89 89 102 102 114 127 127 140 144 149 152 127 130 135 137

16 16 17 21 22 25 29 30 32 33 37 40 44 49 56 57 64 68 73 79 83 86 89 135 137

16 16 17 21 22 25 29 30 32 33 37 40 44 49 56 79 87 97 103

23 28 35 44 50 63 76 92 104 117 145 171 222 277 328 360 411 462 514

3 3 3 5 6 8 8 10 10 11 11 13 13 13 13 13 13 13 13

10 11 13 14 16 18 19 21

111

616

13

30 38 49 59 65 78 90 106 122 135 164 192 246 305 365 400 457 505 559 610 664 714 822 924 981

Drilling DIA DIA No of of of Bolt Bolt Bolts Circle Holes 60 16 4 70 16 4 79 16 4 89 16 4 98 16 4 121 19 4 140 19 4 152 19 4 178 19 8 191 19 8 216 22 8 241 22 8 298 22 8 362 25 12 432 25 12 476 29 12 540 29 16 578 32 16 635 32 20 692 35 20 749 35 20 806 35 24 914 35 28 1029 41 32 1086 41 32

Length of Bolts Stud Bolts Mach. DIA of Bolts Bolts 1,6mm 1,6mm UNC RF RJ RF 1/2 60 51 1/2 60 51 1/2 65 76 57 1/2 65 76 57 1/2 70 83 57 5/8 80 89 70 5/8 85 95 76 5/8 90 102 76 5/8 90 102 76 5/8 90 102 76 3/4 95 108 83 3/4 95 108 83 3/4 105 114 89 7/8 115 127 95 7/8 115 127 102 1 130 140 108 1 135 146 114 1 1/8 150 159 121 1 1/8 160 165 133 1 1/4 165 178 1 1/4 175 184 146 1 1/4 180 152 1 1/4 185 159 1 1/2 205 178 1 1/2 210 178

Notes : 1) Sizes not covered in ANSI B 16.5 are taken from the “Tube Turn Catalogue”. 2) Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 1 OF 7

REV. 0

CLASS 300# Nom Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 221) 24 261) 301) 341) 361) 421)

Dimensions as per ANSI B 16.5

O

Q

R

X

Y

Z

B

r

N

95 117 124 133 156 165 191 210 229 254 279 318 381 445 521 584 648 711 775 838 914 972 1092 1207 1270 1448

14 16 17 19 21 22 25 29 30 32 35 37 41 48 51 54 57 60 64 67 70 79 92 102 105 118

35 43 51 64 73 92 105 127 140 157 186 216 270 324 361 413 470 533 584 641 692 749 857 965 1022 1194

52 57 62 65 68 70 76 79 81 86 98 98 111 117 130 143 146 159 162 165 168 184 210 232 241 276

22 25 27 27 30 33 38 43 44 48 51 52 62 67 73 76 83 89 95 102 106 184 210 232 241 276

22 25 27 27 30 33 38 43 44 48 51 52 62 95 102 111 121 130 140

23 28 35 44 50 63 76 92 104 117 145 172 222 277 328 360 411 462 514

3 3 3 5 6 8 8 10 10 11 11 13 13 13 13 13 13 13 13

10 11 13 14 16 18 19 21

152

616

13

Drilling Length of Bolts Stud Bolts Mach. DIA DIA No DIA D of of of of Bolts Bolt Bolt Bolts Bolts 1,6mm 1,6mm Circle Holes UNC RF RJ RF 38 67 16 4 1/2 65 80 55 48 83 19 4 5/8 70 85 65 54 89 19 4 5/8 80 90 65 64 98 19 4 5/8 80 90 70 70 114 22 4 3/4 90 105 80 84 127 19 8 5/8 85 105 80 100 149 22 8 3/4 95 115 85 117 168 22 8 3/4 105 125 90 133 184 22 8 3/4 110 130 95 146 200 22 8 3/4 110 130 95 178 235 22 8 3/4 115 135 105 206 270 22 12 3/4 125 140 110 280 330 25 12 7/8 135 155 125 321 388 29 16 1 155 175 135 375 451 32 16 1 1/8 165 185 150 425 515 32 20 1 1/8 175 195 155 483 572 35 20 1 1/4 185 205 165 533 629 35 24 1 1/4 195 210 175 587 686 35 24 1 1/4 205 225 180 641 743 41 24 1 1/2 225 250 195 702 813 41 24 1 1/2 230 255 200 721 876 44 28 1 5/8 255 280 225 827 997 48 28 1 3/4 290 315 255 937 1105 51 28 1 7/8 315 345 275 991 1168 54 32 2 325 360 290 1154 1340 54 36 2 350 365 305

Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 2 OF 7

REV. 0

CLASS 400# Nom Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 221) 24 1) 26 301) 341) 1) 36 421)

Dimensions as per ANSI B 16.5

O

Q

R

X

Y

Z

B

r

N

95 117 124 133 156 165 191 210 229 254 279 318 381 445 521 584 648 711 775 838 914 972 1092 1207 1270 1448

14 16 17 19 21 22 25 29 30 32 35 37 41 48 51 54 57 60 64 67 70 79 92 102 105 118

35 43 51 64 73 92 105 127 140 157 186 216 270 324 361 413 470 533 584 641 692 749 857 965 1022 1194

52 57 62 65 68 70 76 79 81 86 98 98 111 117 130 143 146 159 162 165 168 184 210 232 241 276

22 25 27 27 30 33 38 43 44 48 51 52 62 67 73 76 83 89 95 102 106 184 210 232 241 276

22 25 27 27 30 33 38 43 44 48 51 52 62 95 102 111 121 130 140

23 28 35 44 50 63 76 92 104 117 145 172 222 277 328 360 411 462 514

3 3 3 5 6 8 8 10 10 11 11 13 13 13 13 13 13 13 13

10 11 13 14 16 18 19 21

152

616

13

Drilling DIA DIA No D of of of Bolt Bolt Bolts Circle Holes 38 67 16 4 48 83 19 4 54 89 19 4 64 98 19 4 70 114 22 4 84 127 19 8 100 149 22 8 117 168 22 8 133 184 22 8 146 200 22 8 178 235 22 8 206 270 22 12 280 330 25 12 321 388 29 16 375 451 32 16 425 515 32 20 483 572 35 20 533 629 35 24 587 686 35 24 641 743 41 24 702 813 41 24 721 876 44 28 827 997 48 28 937 1105 51 28 991 1168 54 32 1154 1340 54 36

Length of Bolts Stud Bolts Mach. DIA of Bolts Bolts 1,6mm 1,6mm UNC RF RJ RF 1/2 65 80 55 5/8 70 85 65 5/8 80 90 65 5/8 80 90 70 3/4 90 105 80 5/8 85 105 80 3/4 95 115 85 3/4 105 125 90 3/4 110 130 95 3/4 110 130 95 3/4 115 135 105 3/4 125 140 110 7/8 135 155 125 1 155 175 135 1 1/8 165 185 150 1 1/8 175 195 155 1 1/4 185 205 165 1 1/4 195 210 175 1 1/4 205 225 180 1 1/2 225 250 195 1 1/2 230 255 200 1 5/8 255 280 225 1 3/4 290 315 255 1 7/8 315 345 275 2 325 360 290 2 350 365 305

Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 3 OF 7

REV. 0

CLASS 600#

Dimensions as per ANSI B 16.5

Nom

Drilling

Pipe

DIA

Size Inch

O

Q

R

X

Y

Z

B

r

N

1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 221) 24 261) 301) 1) 34 361) 1) 42

95 117 124 133 156 165 191 210 229 273 330 356 419 508 559 603 686 743 813 870 940 1016 1130 1245 1314 1492

14 16 17 21 22 25 29 32 35 38 44 48 56 64 67 70 76 83 89 95 102 108 114 121 124 140

35 43 51 64 73 92 105 127 140 157 189 216 270 324 381 413 470 533 584 641 692 749 857 965 1022 1194

52 57 62 67 70 73 79 83 86 102 114 117 133 152 156 165 178 184 191 197 203 222 248 270 283 324

22 25 27 29 32 37 41 46 49 54 60 67 76 86 92 94 106 117 127 133 140 222 248 270 283 324

22 25 27 29 32 37 41 46 49 54 60 67 76 111 117 127 140 152 165 184 -

23 28 35 44 50 63 75 91 104 117 145 171 222 277 328 360 411 462 514 616 -

3 3 3 5 6 8 8 10 10 11 11 13 13 13 13 13 13 13 13 13 -

10 11 13 14 16 17 19 21 -

D

DIA

No

of of of Bolt Bolt Bolts Circle Holes 38 67 16 4 48 83 19 4 54 89 19 4 64 98 19 4 70 114 22 4 84 127 19 8 100 149 22 8 118 168 22 8 133 184 25 8 152 216 25 8 189 267 29 8 222 292 29 12 273 349 32 12 343 432 35 16 400 489 35 20 432 527 38 20 495 603 41 20 546 654 44 20 610 724 44 24 667 778 48 24 718 838 51 24 748 914 51 28 862 1022 54 28 973 1130 60 28 1032 1194 67 28 1202 1365 73 28

DIA

Length of Bolts Stud Bolts Mach.

of Bolts Bolts 6,4mm 6,4mm UNC RF RJ RF 1/2 80 80 70 5/8 85 85 80 5/8 90 90 85 5/8 95 95 90 3/4 105 105 95 5/8 105 110 95 3/4 115 125 110 3/4 125 130 125 7/8 135 140 130 7/8 140 150 135 1 160 165 155 1 165 175 160 1 1/8 195 200 185 1 1/4 210 220 205 1 1/4 215 225 210 1 3/8 230 235 225 1 1/2 250 260 245 1 5/8 270 275 260 1 5/8 290 295 280 1 3/4 305 320 300 1 7/8 325 340 320 1 7/8 340 350 330 2 360 370 350 2 1/4 385 400 375 2 1/2 400 420 395 2 3/4 445 460 440

Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 4 OF 7

REV. 0

CLASS 900# Nom Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12 14 16 18 20 24 261) 301) 341) 361)

O

Q

Dimensions as per ANSI B 16.5 R

X

Y

Z

B

r

-

D

Drilling Length of Bolts Stud Bolts Mach. DIA DIA No DIA of of of of Bolts Bolt Bolt Bolts Bolts 6,4mm 6,4mm Circle Holes UNC RF RJ RF

USE CLASS 1500 DIMENSIONS IN THESE SIZES

241 292 349 381 470 546 610 641 705 787 857 1041 1086 1232 1397 1461

38 44 51 56 64 70 79 86 89 102 106 140 140 149 165 171

127 157 186 216 270 324 381 413 470 533 584 692 749 857 965 1022

102 114 127 140 162 184 200 213 216 229 248 292 286 311 349 362

54 70 79 86 102 108 117 130 133 152 159 203 286 311 349 362

54 70 79 86 114 127 143 156 165 191 210 267 -

91 117 145 171 222 277 328 360 411 462 514 616 -

10 11 11 13 13 13 13 13 13 13 13 13 -

-

127 159 191 235 298 368 419 451 508 585 622 749 775 889 1006 1064

191 235 279 318 394 470 533 559 616 686 749 902 952 1086 1226 1289

25 32 35 32 38 38 38 41 44 51 54 67 73 79 92 92

8 8 8 12 12 16 20 20 20 20 20 20 20 20 20 20

7/8 1 1/8 1 1/4 1 1/8 1 3/8 1 3/8 1 3/8 1 1/2 1 5/8 1 7/8 2 2 1/2 2 3/4 3 3 1/2 3 1/2

140 165 185 195 220 230 250 270 280 325 345 435 445 480 535 550

150 175 195 195 225 235 255 280 295 340 360 455 480 510 575 585

135 160 180 185 310 225 245 260 275 320 340 425 440 470 530 540

Note: 1. Sizes not covered in ANSI B 16.5 are taken from the “Tube Turn Catalogue”.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 5 OF 7

REV. 0

CLASS 1500# Nom, Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12 14 16 18 20 24

Dimensions as per ANSI B 16.5

O

Q

R

X

Y

Z

B

r

N

D

121 130 149 159 178 216 244 267 311 375 394 483 584 673 749 826 914 984 1168

22 25 29 29 32 38 41 48 54 73 83 92 108 124 133 146 162 178 203

35 43 51 64 73 92 105 127 157 186 216 270 324 381 413 470 533 584 692

60 70 73 73 83 102 105 117 124 156 171 213 254 283 298 311 327 356 406

32 35 41 41 44 57 64 73 90 105 119 143 159 181 -

32 35 41 41 44 57 64 73 90 105 119 143 178 219 241 260 276 292 330

23 28 35 44 50 62 75 91 117 145 171 222 277 328 360 411 462 514 616

3 3 3 5 6 8 8 10 11 11 13 13 13 13 13 13 13 13 13

10 11 13 14 16 17 19 -

38 44 52 64 70 105 124 133 162 197 229 292 368 451 495 552 597 641 762

Drilling Length of Bolts Stud Bolts Mach. DIA DIA No DIA of of of of Bolts Bolt Bolt Bolts Bolts 6,4mm 6,4mm Circle Holes UNC RF RJ RF 83 22 4 3/4 105 105 95 89 22 4 3/4 110 110 105 102 25 4 7/8 125 125 115 111 25 4 7/8 125 125 115 124 29 4 1 135 135 130 165 25 8 7/8 140 150 135 191 29 8 1 155 160 150 203 32 8 1 1/8 175 180 165 241 35 8 1 1/4 195 200 185 292 41 8 1 1/2 245 250 235 318 38 12 1 3/8 255 260 250 394 44 12 1 5/8 290 300 280 483 51 12 1 7/8 340 345 330 572 54 16 2 375 390 370 635 60 16 2 1/4 410 425 400 705 67 16 2 1/2 445 470 440 775 73 16 2 3/4 490 515 485 832 79 16 3 535 565 530 991 92 16 3 1/2 610 650 605

Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 6 OF 7

REV. 0

CLASS 2500# Nom. Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12

O

133 140 159 184 203 235 267 305 356 419 483 552 673 762

Q

30 32 35 38 44 51 57 67 76 92 108 127 165 184

Dimensions as per ANSI B 16.5 R

35 43 51 64 73 92 105 127 157 186 216 270 324 381

X

73 79 89 95 111 127 143 168 191 229 273 318 419 464

Y

40 43 48 52 60 70 79 92 108 130 152 178 229 254

Z

B

40 43 48 52 60 70 79 92 108 130 152 178 229 254

23 28 35 44 50 62 75 91 117 145 171 222 277 328

r

3 3 3 5 6 8 8 10 11 11 13 13 13 13

-

-

D

43 51 57 73 79 95 114 133 165 203 235 305 375 441

Drilling DIA DIA No of of of Bolt Bolt Bolts Circle Holes 89 22 4 95 22 4 108 25 4 130 29 4 146 32 4 171 29 8 197 32 8 229 35 8 273 41 8 324 48 8 368 54 8 438 54 12 540 67 12 619 73 12

Length of Stud Bolts DIA of Bolts UNC 3/4 3/4 7/8 1 1 1/8 1 1 1/8 1 1/4 1 1/2 1 3/4 2 2 2 1/2 2 3/4

0,25" RF

RJ

M&F T&G

125 125 135 150 165 175 195 220 250 295 345 385 485 535

125 125 135 155 175 180 200 225 260 315 360 400 510 560

115 115 130 140 160 165 185 210 245 290 340 375 480 530

Bolt length is including 2mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF ANSI FLANGES Doc. No : 30101-30-17D-208 C:\webpage\piping_std\30101-30-17D-208.doc

BAA Checked

Approved

SHT. 7 OF 7

REV. 0

RTJ FLANGES

Nom. Pipe Size Inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

K

64 73 83 102 121 133 154 172 193 219 273 330 406 425 483 546 597 711

FLANGE RATING Class 150 # Class 300#/400#/600# Class 900 # P L=E Ring K P L=E Ring K P L=E Ring 3) 3) 3) No No No

48 57 65 83 102 114 132 149 171 194 248 305 381 397 454 518 559 673

6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4 6,4

R15 R17 R19 R22 R25 R29 R33 R36 R40 R43 R48 R52 R56 R59 R64 R68 R72 R76

51 64 70 80 91 108 127 146 159 175 210 241 302 356 413 457 508 575 635 749

34 43 51 60 68 83 102 124 132 149 181 211 270 324 381 419 469 533 584 692

5,6 6,4 6,4 6,4 6,4 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 7,9 9,5 11,1

R11 R13 R16 R18 R20 R23 R26 R31 R34 R37 R41 R45 R49 R53 R57 R61 R65 R69 R73 R77

K

156

124

7,9

R31

61 67 72 81 92 124 137 168

181 216 241 308 362 419 467 524 594 648 772

149 181 211 270 324 381 419 469 533 584 692

7,9 7,9 7,9 7,9 7,9 7,9 11,1 11,1 12,7 12,7 15,9

R37 R41 R45 R49 R53 R57 R62 R66 R70 R74 R78

194 229 248 318 371 438 489 546 613 673 794

USE CLASS 1500

Class 1500 # P L=E Ring No

K

Class 2500 # P L=E Ring No

40 44 51 60 68 95 108 137

6,4 6,4 6,4 6,4 6,4 7,9 7,9 7,9

R2 R14 R16 R18 R20 R4 R27 R35

65 73 82 102 114 133 149 168

43 51 60 72 83 102 111 127

6,4 6,4 6,4 7,9 7,9 7,9 9,5 9,5

R13 R16 R18 R21 R23 R26 R28 R32

162 194 211 270 324 381 419 470 533 584 692

7,9 7,9 9,5 11,1 11,1 14,3 15,9 17,5 17,5 17,5 20,6

R39 R44 R46 R50 R54 R58 R63 R67 R71 R75 R79

203 241 279 340 425 495

157 191 229 279 343 406

11,1 12,7 12,7 14,3 17,5 17,5

R38 R42 R47 R51 R55 R60

Notes : 1) Sizes not covered in ANSI B 16.5 are taken from MSS SP 44 and ANSI 16.5. 2) All other dimensions are equal to WN Flanges 3) Dimensions also applicable for 600#

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF RTJ FLANGES Doc. No : 30101-30-17D-209 K\:BU3\30101\30\PIPING.MAN\30101-30-17D-209

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

ASSEMBLY OF RTJ FLANGES

Dimensions as per ANSI B 16.5 Nom Pipe Size Inch 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24

0 Rev.

Class 150

Class 300

A

B

56 62 64 70 76 89 102 102 114 127 127 139,7 114,5 152,4

4 4 4 4 4 4 4 4 4 3 3 3 3 3

01/2002 Date

A 52 57 62 68 70 79 86 98 111 118 130 143 145 159 162 168

Class 400 B 3 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6

A 58 64 68 74 76 85 92 104 117 123 136 149 152 165 168 174

B 3 4 4 4 5 5 6 6 6 6 6 6 6 6 6 6

FLANGE RATING Class Class 600 900 A B A B 59 3 64 4 68 4 76 4 80 5 89 5 108 4 108 5 121 4 124 5 146 4 140 5 168 4 159 5 191 4 162 5 206 4 172 5 219 4 184 5 222 4 191 5 235 6 199 5 254 6 210 6 299 6

First Issue Description

Class 1500 A 67 76 79 89 109 124 130 179 219 260 289 305 317 333 362 413

B 4 4 4 4 3 3 3 3 4 4 5 6 8 8 10 11

LEA Prepared

PIPING HAND BOOK DIMENSIONS OF RTJ FLANGES Doc. No : 30101-30-17D-209 K\:BU3\30101\30\PIPING.MAN\30101-30-17D-209

Class 2500 A 79 86 95 118 133 175 197 279 324 426 470

B 4 4 4 3 3 3 4 4 5 6 8

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

STUB-ENDS According to MSS SP-43 type A / B and ANSI B 16.9

Nom.

OD

Diam

Appr.

Pipe Size Inch

Pipe d

D

ANSI

MSS

Sched. 5S

1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12 14 16 18 20 24

21.34 26.27 33.4 42.16 48.26 60.32 73.02 88.9 114.3 141.3 168.27 219.07 273.05 323.85 355.6 406.4 457.2 508 609.6

34.9 42.8 50.8 63.5 73 92 104.8 127 157.2 185.7 215.9 270 324 381 412.8 470 533.4 584.2 692.2

76.2 76.8 101.6 101.6 101.6 152.4 152.4 152.4 152.4 203.2 203.2 203.2 254 254 305 305 305 305 305

50.8 50.8 50.8 50.8 50.8 63.5 63.5 63.5 76.2 76.2 88.9 101.6 127 152.4 152.4 152.4 152.4 152.4 152.4

1.65 1.65 1.65 1.65 1.65 1.65 2.11 2.11 2.11 2.77 2.77 2.77 3.4 3.96 3.96 4.19 4.19 4.77 5.54

length in mm

Weight kg / each Sched.10S Sched.40S Sched.40S S in mm

2.11 2.11 2.77 2.77 2.77 2.77 3.05 3.05 3.05 3.4 3.4 3.76 4.19 4.57 4.77 4.77 4.77 5.54 6.35

2.77 2.87 3.38 3.56 3.68 3.91 5.16 5.49 6.02 6.55 7.11 8.18 9.27 9.53 9.53 9.53 9.53 9.53 9.53

0.14 0.18 0.31 0.42 0.52 1.01 2.13 2.13 3.09 5.35 6.94 10.48 18.1 22.32 28.94 33.52 38.65 42.96 52.62

Notes : For material 304, 304L and 316L Type A : R to suit lap joint flange Type B : R to suit slip-on flange

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HANDBOOK

STUB ENDS Doc. No : 30101-30-17D-210 C:\webpage\piping_std\30101-30-17D-210.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

SIZE 1/2 3/4 1 11/2 2 Class 3 150 4 R.F. 6 8 10 12 14 16 18 20 24

O.D 21 27 33 48 60 89 114 168 219 273 324 358 406 457 508 610

A 73 81 94 119 128 156 181 232 280 318 368 406 432 483 525 584

B 86 81 94 119 140 184 226 318 407 483 571 660 737 826 906 1066

C 53 58 76 114 140 140 140 140 140 140 140 140 140 140 140 140

D 89 98 108 127 152 191 229 279 343 406 485 535 595 635 700 815

SIZE 1/2 3/4 1 11/2 2 Class 3 300 4 R.F 6 8 10 12 14 16 18 20 24

A 1) B 1)

D 95 117 124 156 165 210 254 318 381 445 521 584 648 711 775 914

G 14 16 17 21 22 29 32 37 41 48 51 54 57 60 64 70

H U 52 22 57 25 62 27 66 30 70 33 79 43 86 48 98 52 111 62 117 67 130 73 143 76 146 83 159 89 162 95 168 106

77 90 86 86 100 100 125 125 134 146 165 193 191 238 241 327 289 416 333 496 384 587 422 676 451 756 502 845 543 924 600 1082

E 25 29 38 57 64 86 105 143 178 216 254 279 305 343 381 432

F 38 29 38 57 76 114 152 229 305 381 457 533 610 686 762 914

G 11 13 14 17 19 24 24 25 29 30 32 35 37 40 43 48

H 48 52 56 62 64 70 76 89 102 102 114 127 127 140 144 152

K 16 11 22 29 35 51 64 95 127 159 190 222 254 286 318 381

N P R 23 55 54 16 36 50 31 75 60 41 99 86 50 120 111 72 174 165 91 219 218 134 324 324 180 434 432 225 543 540 289 649 647 314 758 756 358 867 864 404 976 972 450 1086 1080 539 1301 1295

L S T 54 38 36 39 28 51 64 42 64 90 61 76 114 79 89 168 117 102 217 153 140 324 229 152 432 305 178 541 382 203 648 458 330 758 534 356 865 611 381 973 687 508 1082 764 508 1297 915

W 25 25 38 38 38 51 64 89 102 127 152 165 178 203 229 267

BOLTS 4 x 1/2" 4 x 5/8" 4 x 5/8" 4 x 3/4" 8 x 5/8" 8 x 3/4" 8 x 3/4" 12 x 3/4" 12 x 7/8 16 x 1" 16 x 11/8" 20 x 11/8" 20 x11/4" 24 x11/4" 24 x11/4" 24 x 11/2"

U BOLTS 16 4 x 1/2" 16 4 x 1/2" 17 4 x 1/2" 22 4 x 1/2" 25 4 x 5/8" 30 4 x 5/8" 33 8 x 5/8" 40 8 x 3/4" 44 8 x 3/4" 49 12 x 7/8" 56 12 x 7/8" 57 12 x 1" 64 16 x 1" 68 16 x 11/8" 73 20 x 11/8" 83 20 x 11/4"

RED, 3/4 x 1/2 1 x 3/4 11/2 x 1 2 x 11/2 3x2 4x3 6x4 8x6 10 x 8 12 x 10 14 x 12 16 x 14 18 x 16 20 x 18 24 x 20

M 3 3 8 6 14 13 27 25 27 25 16 25 25 25 51

RED,

M

1 x 1/2 11/2 x 3/4 2x1 3 x 11/2 4x2 6x3 8x4 10 x 6 12 x 8 14 x 10 16 x 12 18 x 14 20 x 16 24 x 18

6 11 14 21 27 40 52 52 52 41 41 51 51 76

RED,

M

11/2 x 1/2 2 x 3/4

14 17

4 x 11/2

33

10 x 4 12 x 6 14 x 8 16 x 10 18 x 12 20 x 14 24 x 16

79 78 68 14 x 6 67 16 x 8 67 18 x 10 76 20 x 12 102

FOR GENERAL NOTES SEE SHT2

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BUILT-UP DIM. FITTINGS AND FLANGES Doc. No : 30101-30-17D-211 C:\webpage\piping_std\30101-30-17D-211.doc

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

RED,

M

94 99 92 94

SIZE 1/2 3/4 1 11/2 2 Class 3 600 4 RF 6 8 10 12 14 16 18 20 24

A 1)

B 1)

83 92 106 133 143 175 213 267 318 375 416 450 489 534 578 643

96 92 106 133 155 203 260 353 445 540 619 704 794 877 958 1124

SIZE 1/2 3/4 1 11/2 2 Class 3 1500 4 RF 6 8 10 12 14 16 18 20 24

A 1)

B 1)

91 105 118 145 172 210 235 321 397 478 543 584 623 677 743 845

104 105 118 145 184 238 282 407 524 641 746 836 928 1020 1124 1327

B 1)

D 95 117 124 156 165 210 273 356 419 508 559 603 686 743 813 940

G 20 22 24 29 32 36 44 54 62 70 73 76 83 89 95 108

H 58 63 68 76 79 90 108 124 140 159 162 171 184 191 197 210

U 29 32 33 36 43 52 60 73 83 92 96 100 113 124 133 146

BOLTS 4 x 1/2" 4 x 5/8" 4 x 5/8" 4 x 3/4" 8 x 5/8" 8 x 3/4" 8 x 7/8" 12 x 1" 12 x 11/8" 16 x 11/4" 20 x 11/4" 20 x 13/8" 20 x 11/2" 20 x 15/8" 24 x1 5/8" 24 x 17/8"

SIZE 1/2 3/4 1 11/2 2 Class 3 900 4 RF 6 8 10 12 14 16 18 20 24

A 1)

194 226 289 346 407 461 496 527 578 635 730

222 273 375 473 572 664 752 832 921 1016 1212

241 292 381 470 545 610 641 705 787 857 1041

44 51 62 70 76 85 92 95 108 114 146

D 121 130 149 178 216 267 311 394 483 584 673 749 825 915 985 1168

G 28 31 35 38 44 54 60 89 99 114 130 140 152 168 184 210

H 66 76 80 89 108 124 130 178 219 260 289 305 318 334 362 413

U 38 41 48 51 64 80 97 125 149 165 187 -

BOLTS 4 x 3/4 4 x 3/4 4 x 7/8 4x1 8 x 7/8 8 x 11/8" 8 x 11/4" 12 x 13/8" 12 x 15/8" 12x 17/8" 16 x 2" 16 x 2 1/4" 16 x 2 1/2" 16 x 23/4" 16 x 3" 16 x 3 1/2"

SIZE 1/2 3/4 1 11/2 2 Class 3 2500 4 RF 6 8 10 12 14 16 18 20 24

A 1)

B 1)

104 114 133 175 197 261 302 422 502 641 724

117 115 133 175 209 289 349 508 629 806 927

D 133 140 159 203 235 305 356 483 552 673 762

G 36 38 41 51 57 73 83 114 133 171 191

D

G

H

U

BOLTS

108 121 146 168 191 207 219 222 235 254 296

60 76 92 108 114 124 136 140 159 165 210

8 x 7/8" 8 x 11/8" 12 x 11/8" 12 x 13/8" 16 x 13/8" 20 x 13/8" 20 x 11/2" 20 x 15/8" 20x 17/8" 20 x 2" 20 x 21/2"

H 79 86 95 117 133 175 197 279 324 425 470

U -

BOLTS 4 x 3/4 4 x 3/4 4 x 7/8 4 x 11/8" 8 x 1" 8 x 11/4" 8 x 11/2" 8 x 2" 12 x 2" 12 x 21/2" 12 x 23/4"

USE CLASS 1500

Notes: 1. For bolt diam. 11/2” and up bolt tensioning may be required, if so add min. 100 mm to dim “A” and “B”. 2. All elbows used are long radius 3. All fitting dimensions as per ANSI. STD B 16.9 and B 16.5 4. All built up dimensions are excluding root cap.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BUILT-UP DIM. FITTINGS AND FLANGES Doc. No : 30101-30-17D-211 C:\webpage\piping_std\30101-30-17D-211.doc

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

SIZE 1/2 3/4 1 11/2 2 Class 3 900 4 RTJ 6 8 10 12 14 16 18 20 24

A

B

D

G

H

U

BOLTS

USE CLASS 1500

196 227 291 346 408 462 503 532 584 641 740

224 274 377 475 573 665 757 837 927 1022 1222

241 292 381 470 546 610 641 705 787 857 1041

46 52 64 71 78 87 97 100 114 121 156

110 122 148 170 192 208 224 227 241 260 308

62 78 94 110 116 129 141 144 165 171 219

8 x 7/8" 8 x 11/8" 12 x 11/8" 12 x 13/8" 16 x 13/8" 20 x 13/8" 20 x 11/2" 20 x 15/8" 20 x 17/8" 20 x 2" 20 x 21/2"

SIZE 1/2 3/4 1 11/2 2 Class 3 1500 4 RTJ 6 8 10 12 14 16 18 20 24 SIZE 1/2 3/4 1 11/2 2 Class 3 2500 4 RTJ 6 8 10 12 14 16 18 20 24

A

B

D

G

H

U

92 105 118 146 174 211 237 324 402 484 551 593 634 687 754 859

105 105 118 146 186 239 284 410 529 649 754 847 939 1030 1135 1341

121 130 149 178 216 267 311 394 483 584 673 749 825 914 984 1168

29 32 35 38 46 56 62 92 103 119 138 149 164 180 195 224

67 76 80 89 110 125 132 181 224 268 297 324 329 345 373 427

38 41 48 51 69 81 98 129 154 170 195 -

A

B

D

G

H

U

104 115 133 178 199 264 307 429 510 653 735

117 115 133 178 211 292 354 515 637 818 938

133 140 159 203 235 305 356 483 550 673 762

36 38 41 52 59 76 87 121 141 183 202

79 86 95 119 135 178 202 286 332 437 481

-

BOLTS 4 x 3/4" 4 x 3/4" 4 x 7/8" 4 x 1" 8 x 7/8" 8 x 11/8" 8 x 11/4" 12 x 13/8" 12 x 15/8" 12 x 17/8" 16 x 2" 16 x 21/4" 16 x 21/2" 16 x 23/4" 16 x 3" 16 x 31/2" BOLTS 4 x 3/4" 4 x 3/4" 4 x 7/8" 4 x 11/8" 8 x 1" 8 x 11/4" 8 x 11/2" 8 x 2" 12 x 2" 12 x 21/2" 12 x 23/4"

Note: 1. For bolt diam. 11/2” and up bolt tensioning may be required, if so add min. 100 mm to dim “A” and “B”. 2. All elbows used are long radius 3. All fitting dimensions as per ANSI. STD B 16.9 and B 16.5 4. All built up dimensions are excluding root cap.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BUILT-UP DIM. FITTINGS AND RTJ FLG’S Doc. No : 30101-30-17D-212 C:\webpage\piping_std\30101-30-17D-212.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Run Pipe Pipe weight/Sch Std / 40 2" XS / 80 XXS / 160 Std / 40 3" XS / 80 XXS / 160 Std / 40 4" XS / 80 XXS / 160 Std / 40 6" XS / 80 XXS / 160 8" Std / 40 XS / 80 10" Std / 40 XS / 80 12" Std / 40 XS / 80 14" Std / 40 XS / 80 16" Std / 40 XS / 80 18" Std / 40 XS / 80 20" Std / 40 XS / 80 24" Std / 40 XS / 80

1/2" 51 51 61 65 65 75 78 78 88 105 105 115 131 131 158 158 183 183 199 199 225 225 250 250 275 275 326 326

3/4" 54 54 64 68 68 79 81 81 91 108 108 118 135 135 161 161 186 186 202 202 228 228 253 253 279 279 329 329

1" 59 59 70 73 73 84 86 86 97 113 113 124 138 138 165 165 191 191 207 207 232 232 258 258 283 283 334 334

1,5" 65 65 83 80 80 91 92 92 110 119 119 137 145 145 172 172 197 197 213 213 238 238 264 264 289 289 340 340

2" 70 70 87 84 84 102 97 97 114 124 124 141 149 149 176 176 202 202 218 218 243 243 268 268 294 294 345 345

DIMENSION " L " FOR OUTLET SIZE 2,5" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"

88 88 109 101 101 121 128 128 148 153 153 180 180 205 205 221 221 247 247 272 272 298 298 348 348

91 91 120 104 104 132 131 131 159 156 156 183 183 209 209 224 224 250 250 275 275 301 301 351 351

111 111 145 138 138 171 164 164 191 191 216 216 232 232 257 257 283 283 308 308 359 359

148 165 192 173 191 200 218 225 243 241 259 267 284 292 310 318 335 368 386

183 212 210 239 236 264 252 280 277 306 302 331 328 356 379 407

218 236 244 260 260 276 285 301 310 326 336 352 387 403

252 266 268 285 293 310 318 336 344 361 395 412

271 287 296 307 322 333 347 358 398 409

301 320 326 339 352 364 403 415

335 352 356 370 406 421

376 386 411 446 429 449

Note : 1. Dimensions are based on Bonny Forge catalogue 1983 2. Weld or root gap (1,6 mm ) included in dimension “L”

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BUILD-UP DIM. WELDOLETS Doc. No : 30101-30-17D-213 C:\webpage\piping_std\30101-30-17D-213.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Run Pipe 3/4" 1" 1,5" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"

3000# - DIM "L" OUTLET SIZE 1/2" 3/4" 1" 1,5" 40 44 45 51 53 59 57 59 65 67 71 73 79 81 84 86 92 94 111 113 119 121 137 138 144 146 164 165 171 173 189 190 197 198 205 206 213 214 230 232 238 240 256 257 264 265 281 283 289 291 332 333 340 341

3000# - DIM "L 1" OUTLET SIZE 1/2" 3/4" 1" 1,5" 31 34 33 42 40 46 48 46 52 54 62 60 67 68 75 73 79 81 102 10 106 108 127 125 132 133 154 152 159 160 179 178 184 186 195 194 200 202 221 219 225 227 246 244 251 252 272 270 276 278 322 321 327 329

Run Pipe

6000# - DIM "L" OUTLET SIZE 1/2" 3/4" 1" 1,5" 3/4" 47 1" 50 55 1,5" 58 62 65 2" 64 68 71 75 3" 78 83 86 89 4" 91 95 98 102 6" 118 122 125 129 8" 143 148 151 154 10" 170 175 178 181 12" 195 200 203 206 14" 200 205 208 211 16" 237 241 244 248 18" 262 267 270 273 20" 287 292 295 298 24" 338 343 346 349

6000# - DIM "L 1" OUTLET SIZE 1/2" 3/4" 1" 1,5" 37 41 42 48 50 53 54 56 59 62 68 70 73 76 81 83 86 89 108 110 113 116 133 135 138 141 160 162 165 168 186 187 190 194 191 192 195 199 227 229 232 235 252 254 257 260 278 279 283 286 330 331 343 337

Notes : 1. Dimensions are based on Bonny Forge catalogue 1983 2. Weld or root gap (1.6mm) included in dimension “L” and “L1”.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BUILD-UP DIM. SOCKOLETS & TREADOLETS Doc. No : 30101-30-17D-214 C:\webpage\piping_std\30101-30-17D-214.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Branch Size 24 20 18 16 14 12 10 8 6 4 3 2

A B A B A B A B A B A B A B A B A B A B A B A B

Header Pipe Size

610 560 600 510 585 470 580 445 550 420 535 410 510 385 495 360 485 330 470 305 460 295 460 280

550 495 535 470 510 445 495 420 485 410 460 385 445 360 435 330 420 305 410 280 410 280

510 470 485 445 470 420 460 395 435 370 420 345 410 320 395 295 385 280 385 270

460 435 445 410 435 385 410 360 395 330 385 305 370 280 360 270 360 255

420 410 410 385 385 360 370 330 360 305 345 280 330 270 330 255

385 370 360 345 360 320 345 295 330 270 320 255 305 245

330 330 330 305 320 280 305 255 295 245 280 230

305 305 295 280 280 255 270 245 255 230

270 270 255 230 245 230 230 220

220 220 220 220 205 205

205 205 195 195

180 180

24

20

18

16

14

12

10

8

6

4

3

2

Note : 1. If specifications call for weld tees, this dimension shall be fitting to fitting, in order to save one weld. 2. Dimensions A & B are based on the following: X = the length of a standard Tee, but not less than 75 mm. Y = 75 ± 3 mm. 3. All dimensions are ± 10 mm. Chart should be used for 150#, 300# RF, RJ & S.T. & G. flanges

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BRANCH DIM. I50# & 300# WN FLANGES Doc. No: 30101-30-17D-215 C:\webpage\piping_std\30101-30-17D-215.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

1

Re-inforcing pads shall be specified as required per “BRANCH TABLE” of the piping material specification.

2

Re-inforcing pads shall never be used at hot dipped galvanised piping.

3

Re-inforcing pads shall be made out of run pipe up to the following limitations: • Maximum wall thickness of 19 mm. • Minimum wall thickness of 3mm. Contact stress department for pad details outside above limitations.

4

The width of a re-inforcing pad is 1/2 O.D of the branch, with a minimum of 50 mm, rounded off to the nearest 5 mm.

5

A 6 mm weep hole shall be provided in the pad as per detail below. This weep hole shall be closed after welding with a soft (PTFE) plug.

Note: Location of branch not over longitudinal or circumferential weld of run pipe.

6

0 Rev.

Method of specifying a reinforcing pad on an isometric is as follow:

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK REINFORCING PAD REQUIREMENTS Doc. No : 30101-30-17D-216 C:\webpage\piping_std\30101-30-17D-216.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

RUN PIPE 1 1.1/2 2 3 4 6 8 10 12 14 16 18 20 24

0 Rev.

01/2002 Date

CLASS 150 25 25 32 32 32 35 35 41 41 45 45 54 57 60

CLASS 300 32 35 32 35 35 35 41 45 51 51 60 60 70 70

DIMENSION 'A' CLASS CLASS 600 900 38 54 41 57 38 54 41 54 47 64 51 64 57 76 64 76 67 76 70 83 76 89 83 98 83 114 95 140

First Issue

CLASS 1500 54 57 54 64 70 76 89 98 102 114 124 152 165 191

CLASS 2500 54 64 57 70 79 89 102 102 127 137

LEA Description

Prepared

PIPING HANDBOOK BUILD-UP DIMENSIONS FOR PAD FLG’S Doc. No : 30101-30-17D-217 C:\webpage\piping_std\30101-30-17D-217.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

0 Rev.

01/2002 Date

First Issue

LEA Description

Prepared

PIPING HANDBOOK UNC OR ISO BOLTS FOR ANSI FLANGES Doc. No : 30101-30-17D-218 C:\webpage\piping_std\30101-30-17D-218.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Note: 1 Face to face dimension all valves acc. To ANSI B16.10 2 3

0 Rev.

Hand wheel, spindle, wrench dimensions etc. may vary with individual manufactures. Non-standard.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK FLANGED VALVES RF 150# UP/TO 300# Doc. No : 30101-30-17D-230 C:\webpage\piping_std\30101-30-17D-230.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Note:

1

2

0 Rev.

01/2002 Date

Face to face dimension all valves according to ANSI B16.10 Hand wheel, spindle, wrench dimensions etc. may vary with individual manufactures.

First Issue Description

LEA Prepared

PIPING HANDBOOK FLANGED VALVES RF 600# UP/TO 2500# Doc. No : 30101-30-17D-231 C:\webpage\piping_std\30101-30-17D-231.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Valve Size

Valve Rating Class 150 Class 300 Class 600 A a A a A a 1/2 184 98 190 102 203 108 3/4 184 98 194 103 206 110 1 184 95 197 102 210 108 1 1/2 222 113 235 119 251 127 2 254 138 267 145 286 154 3 298 173 318 183 337 192 4 352 206 368 214 394 227 6 451 265 473 276 508 294 8 543 322 568 335 610 356 10 673 394 708 411 752 433 12 737 457 775 476 819 499 16 1016 594 1057 614 1108 640 Based on K & K type 1400 valve

0 Rev.

01/2002 Date

B

C

D

526 526 562 583 656 703 732 983 1262 1349 1418 1529

89 89 114 133 148 195 225 313 351 405 473 584

251 251 359 359 400 400 400 514 514 667 667 667

First Issue Description

LEA Prepared

PIPING HAND BOOK GLOBE TYPE CONTROL VALVE Doc. No : 30101-30-17D-232 C:\webpage\piping_std\30101-30-17D-232.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Flanged and wafer type control valve with Spring Diaphragm Actuator

A Valve Thr'd Flg'd Size Ends & Flg. less 1 102 102 1 1/2 137 114 2 146 124 3 165 4 194 6 229 8 243 10 297 12 338 14 475 (150) 14 513 (300)

B

C

D

173 175 175 262 264 330 333 335 338 343

297 300 300 434 437 533 536 538 541 541

208 211 211 229 229 302 305 310 312 312

E F

163 163 163 163 163 254 254 254 254 254

140 140 140 175 175 218 218 218 218 218

G

Thr'd Ends

114 117 117 122 122 213 216 221 224 226

67 84 84

343 541 312 254 218 226

H Flg. less

Flg'd

J

K

L

67 62 62 97 106 127 148 167 184 257

51 59 62 86 106 106 106 106 106 257

206 234 239 333 356 432 470 574 610 742

38 51 66 84 109 147 203 251 277 292

137 165 170 244 267 322 361 465 500 630

257

257 742 292 630 note 1 note 1 note 1 note 1

ANSI Class 150 165 165 267 300 330 394 394 503 503 note 1

M ANSI ANSI Class Class 300 400 229 229 254 254 267 267 343 356 356 406 406 470 470 495 521 572 572 630 note 1 note 1

ANSI Class 600 229 254 267 356 419 470 533 622 648 note 1

Note: 1. 14” Camflex II available in flanged construction only. “M” dimension does not apply.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK CAMFLEX TYPE CONTROL VALVES Doc. No : 30101-30-17D-233 C:\webpage\piping_std\30101-30-17D-233.doc

BAA Checked

Approved

SHT. 1 OF 2

REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK CAMFLEX TYPE CONTROL VALVES Doc. No : 30101-30-17D-233 C:\webpage\piping_std\30101-30-17D-233.doc

BAA Checked

Approved

SHT. 2 OF 2

REV. 0

Size Inlet X Outlet 1x2 1 1/2 x 2 1 1/2 x 2 1 1/2 x 3 2x3 2x3 3x4 3x4 4x6 4x6 6x8 6 x 10 8 x 10

Dim 'A' Outlet Class 150 # 114 121 152 124 124 162 162 181 210 222 241 267 279

Class 150 105 124

Dimension ' B ' By Inlet Rating Class Class Class 300 600 900 105 105 105

130 130

124 130 130

130

156

156

156

197

197

197

240

240 240 276

240 240 276

Class 1500

124

154

154

184

184

197

197

H

X

weigth KG

300 300 300 305 350 350 400 525 700 750 1050 1100 1150

305 305 305 305 305 305 660 660 660 660 660 660 660

10 10 10 30 50 65 55 80 100 110 275 300 280

Note : 1. Based on Sempell type VSE 1 2. Relief valve dimensions are for lay-out purpose only.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK RELIEF VALVES UP/TO 1500# Doc. No : 30101-30-17D-234 C:\webpage\piping_std\30101-30-17D-234.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Nom Pipe Size 2 3 4 6 8 10 12 14 16 18 20 24

A ANS ANS ANS B C D Class Class Class 150 300 600 102 108 108 44 30 125 132 146 146 68 50 150 170 178 190 92 60 180 218 248 264 140 90 230 276 304 318 186 120 260 336 358 396 234 140 300 406 418 454 278 160 360 448 482 488 306 180 390 510 536 562 350 200 450 546 594 610 396 220 510 602 650 680 440 240 570 714 772 786 530 280 700

E

F

G

T

H ANS ANS ANS Class Class Class 150 300 600 65 70 70

J

25

3 2

70

4 15

75 3 6

80

80 75 80 85 90

20

30

90 95

35

100 3

85

4 25

85

8

90 95

95 100 105 115

40 105 115 120

45 50

Note : 1. Material as stated on requisition. 2. Dimension “B” is based on ID line pipe conform sched. 80 as per ANSI B 36.10. 3. Pipe size and flange class to be clearly die stamped on both sides of handle e.g. 2” – 150#

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK TEMPORARY STRAINERS Doc. No : 30101-30-17D-235 C:\webpage\piping_std\30101-30-17D-235.doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

Spectacle Blinds 1

This standard is for application when of the shelf or manufactured type blinds are not available.

2

For handling purposes blinds are to be installed preferably in the vertical ( between flanges in horizontal part of the line).

3

Blinds shall be accessible from grade or platform.

4

when blinds exceeds 45 kg. Lifting shall be by mobile equipment. If the blind is not accessible, hitching point shall be provided.

5

Grouped flanges with blinds (e.g. at battery limit) are to be staggered.

6

Hydraulic flange spreaders are to be used for loosing the flanges when blinds are to be turned or replaced.

7

Special attention must be given to the line flexibility when ring joint blinds are used. When possible, install a blind in combination with a flanged elbow.

8

Spectacle blinds are installed at a bolt hole centreline, a hole is provided so the spectacle can rotate over the flange bolt. The lifting lug is installed at an angle, this to clear the flange bolts.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK SPECTACLE BLINDS Doc. No : 30101-30-17D-236 C:\webpage\piping_std\30101-30-17D-236.doc

BAA Checked

Approved

SHT. 1 OF 3

REV. 0

Plate thickness ' T ' Mat.

Rating 2

3

4

Nominal pipe size 6 8 10

Class

1/2

3/4

1

1 1/2

150 RF/FF

5

5

5

6

7

9

10

14

17

300 RF

5

6

7

9

11

15

18

25

31

600 RF

6

7

9

12

15

21

25

34

43 52

12

900 RF

7

9

10

14

17

24

30

41

Carbon

1500 RF

9

11

13

16

21

30

37

52

Steel

2500 RF

11

13

16

22

27

36

47

300 RTJ

17

20

21

23

28

33

36

43

600 RTJ

19

22

23

26

32

39

43

53

900 RTJ

23

24

25

29

37

43

48

61

Spec-

1500 RTJ

25

26

26

33

43

54

61

Tacle

2500 RTJ

30

33

36

47

53

65

79

Blind

150 RF/FF

5

5

5

6

7

9

10

14

17

20

23

300 RF

5

5

5

6

8

11

13

18

23

26

33

600 RF

5

5

6

9

11

15

18

26

32

900 RF

5

6

7

10

12

18

22

31

39

40

Stain-

0 Rev.

18

20

Use paddle 50

less

1500 RF

6

7

9

13

15

22

28

2500 RF

7

9

11

16

20

29

36

300 RTJ

15

17

18

19

24

28

30

36

41

600 RTJ

16

19

20

22

27

32

36

44

51

900 RTJ

20

20

21

24

32

36

40

50

1500 RTJ

21

22

24

27

36

44

50

2500 RTJ

25

27

30

39

44

54

65

First Issue Description

25

Use paddle Spacer & Blind 46

51

LEA Prepared

PIPING HAND BOOK SPECTACLE BLINDS Doc. No : 30101-30-17D-236 C:\webpage\piping_std\30101-30-17D-236.doc

16

Spacer & Blind

Steel

01/2002 Date

14

BAA Checked

Approved

SHT. 2 OF 3

REV. 0

24

Plate thickness ' T ' Mat.

Rating Class

Nominal pipe size 1/2

3/4

1

1 1/2

2

3

4

6

8

10

12

14

150 RF/FF 300 RF

16

18

20

24

28

32

35

80

44

48

54

61

67

85

94

600 RF

51

61

65

75

900 RF

62

74

80

91

80

94

Carbon

1500 RF

Use

Steel

2500 RF

Spectacle Blind

65 67

To be

84

300 RTJ

Calculated 56

63

67

73

600 RTJ

63

72

81

86

96

Paddle

900 RTJ

73

84

96

Spa-

1500 RTJ

Cer

2500 RTJ

and

150 RF/FF

blind

300 RF

77

95

To be 28

900 RF

less

1500 RF

Use

Steel

2500 RF

Spectacle Blind

50 51

900 RTJ 1500 RTJ

63

41

47

51

61

58

65

72

80

48

56

62

70

79

86

95

61

72

86

To be Calculated 55

60

65

73

86

96

58

66

71

77

68

77

90

98

78

To be

2500 RTJ

Calculated

First Issue Description

LEA Prepared

PIPING HAND BOOK SPECTACLE BLINDS Doc. No : 30101-30-17D-236 C:\webpage\piping_std\30101-30-17D-236.doc

41

36

64

59

35

50

300 RTJ 600 RTJ

32

46

39

Stain-

01/2002 Date

90

Calculated

600 RF

0 Rev.

81

BAA Checked

Approved

SHT. 3 OF 3

REV. 0

o

Press. Ratings Material 1 Cast Iron Nodular Cast Iron 2,5 Cast Iron Nodular Cast Iron 6 Cast Iron Nodular Cast Iron 10 Cast Iron Nodular Cast Iron C22 N, GS-45 16 Cast Iron Nodular Cast Iron C22 N, GS-25 25 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 40 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 63 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 100 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 160 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 250 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 320 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10 400 C22 N, GS-25 15Mo3, GS-22 Mo4 13CrMo44, GS-17CrMo55 10CrMo9 10

Allowable working pressure in bar at C 120 200 250 300 350 400 425 450 475 500 510 520 530 540 550 1 1 1 1 2,5 6 10

16 16 25

40

63

100

160

250

320

400

2

1,8

1,5

5 4,5 2 3,6 2 8

7

2

6

2

13 11 3 10 3 14 13 11 10 8 22 20 17 16 13 25 22 20 19 18 17 25 24 23 22 21 20 18 15 35 32 28 24 21 40 35 31 30 29 28 40 38 36 35 34 33 29 24 50 45 40 36 32 63 56 50 47 46 45 63 61 58 57 56 53 47 40 80 70 60 56 50 100 87 78 74 72 70 100 95 91 89 87 82 74 62 130 112 96 90 80 160 139 125 118 115 112 160 153 146 142 139 132 118 100 70 200 175 150 140 125 250 217 195 185 179 174 250 238 227 223 217 206 184 154 124 108 250 225 192 180 160 320 278 250 236 230 222 320 304 292 285 278 264 237 200 158 139 320 280 240 225 200 400 348 312 296 286 278 400 380 364 356 348 330 295 250 198 174

12

9

19

15

32

25

49

38

79 61

62 52

46

35

124 95

97 81

73

54

158 124 121 104

93

69

198 156 116 151 130

87

1) The test pressure is 1,5 x the operation pressure unless otherwise mentioned 2) When bolts of material 5D are used, the working pressure at 200oC is also allowed here. 3) When bolts of material 5D are used, the working pressure of C22 N is allowed here.

0 Rev.

01/2002 Date

Approved Description

LEA Prepared

PIPING HANDBOOK PRESSURE CLASSES ACCORDING DIN Doc. No : 30101-30-17D-304 C:\webpage\piping_std\30101-30-17D-304.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

For flanges ND 10 ≤ 150 take ND 16 For flanges ND 25 ≤ 150 take ND 40

Flg ND 10

Flg ND 16

Flg ND 25

Flg ND 40

200 250 300 350 400 500 600 25 40 50 80 100 150 200 250 300 350 400 500 600 200 250 300 350 400 500 600 25 40 50 80 100 150 200 250 300 350 400 500

25 215 240 265 295 325 380 435 100 120 125 145 155 185 215 245 275 305 335 400 465 225 255 285 320 355 410 465 100 120 125 145 160 195 230 270 300 335 375 420 25

40 220 250 275 305 335 385 440 110 125 135 150 160 195 220 255 280 310 340 410 470 230 265 295 330 360 415 475 110 125 135 150 170 200 240 275 310 340 380 430 40

50 230 255 280 310 340 395 450 115 135 140 160 170 200 230 260 290 320 350 415 480 240 270 300 335 370 425 480 115 135 140 160 175 210 245 285 315 350 390 435 50

80 240 270 295 325 355 405 460 130 145 155 170 180 215 240 275 300 330 360 430 490 250 285 315 350 380 435 495 130 145 155 170 190 220 260 295 330 360 400 450 80

100 255 280 305 335 365 420 475 140 160 165 185 195 225 255 285 315 345 375 440 505 265 295 325 360 395 450 505 140 160 165 185 200 235 270 310 340 375 415 460 100

Pipe Size 150 200 280 305 310 335 335 360 365 390 395 420 445 470 500 525 170 195 185 210 195 220 210 235 220 245 255 280 280 305 315 340 340 365 370 395 400 425 470 495 530 555 290 315 325 350 355 380 390 415 420 445 475 500 535 560 170 195 185 210 195 220 210 235 230 255 260 285 300 325 335 360 370 395 400 425 440 465 490 515 150 200 Pipe Size

250 335 360 385 415 445 500 555 220 240 245 265 275 305 335 365 395 425 455 520 585 345 375 405 440 475 530 585 220 240 245 265 280 315 350 390 420 455 495 540 250

300 360 385 410 440 470 525 580 245 265 270 290 300 330 360 390 420 450 480 545 610 370 400 430 465 500 555 610 245 265 270 290 305 340 375 415 445 480 520 565 300

350 375 405 430 460 490 540 595 265 280 290 305 315 350 375 410 435 465 495 656 625 385 420 450 485 515 570 630 265 280 290 305 325 355 395 430 465 495 535 585 350

400 400 430 455 485 515 565 620 290 305 315 330 340 375 400 435 460 490 520 590 650 410 445 475 510 540 595 655 290 305 315 330 350 380 420 455 490 520 560 610 400

500 450 480 505 535 565 615 670 340 355 365 380 390 425 450 485 510 540 570 640 700 460 495 525 560 590 645 705 340 355 365 380 400 430 470 505 540 570 610 660 500

600 500 530 555 585 615 665 720 390 405 415 430 440 475 500 535 560 590 620 690 750 510 545 575 610 640 695 755 390 405 415 430 450 480 520 555 590 620 660 710 600

200 250 300 350 400 500 600 25 40 50 80 100 150 200 250 300 350 400 500 600 200 250 300 350 400 500 600 25 40 50 80 100 150 200 250 300 350 400 500

Flg ND 10

Flg ND 16

Flg ND 25

Flg ND 40

Notes: 1 INSULATION THICKNESS TO BE ADED AND CHECK INSULATED LINES ON USE OF INSULATED FLANGES. 2 DIMENSIONS ARE BASED ON STAGGERED FLANGES , ALLOW SIDE MOVEMEN DUE TO EXPANSION. 3 DIMENSIONS ARE BASED ON A MINIMUM DISTANCE OF 25 MM BETWEEN FLANGE AND PIPE AND 50 MM BETWEEN FLANGE AND COLUMN OR WALL. 4 THIS TABLE IS NOT VALID FOR VIBRATING LINES. 5 ALLOW SIDE MOVEMENT DUE TO EXPANSION

0 Rev.

01/2002 Date

First Issue Description PIPING HANDBOOK

LEA Prepared

Min. PIPE SPACING W/DIN FLANGES Doc. No : 30101-30-17D-305 C:\webpage\piping_std\30101-30-17D-305.doc

BAA Checked SHT. 1 OF 1

Approved REV. 0

DN

s

O.D

I.D

A

B

C

D

E

F

G

H

K

L

N

T 10 -

P.R

W

Bolts

Red

M

Red

M

Red

M

S

SEE TABLE PN 16

150

PN 10

200 250

6,3 6,3

219,1 273

206,5 260,4

240 284

300

7,1

323.9

309,7

322

350

8

356,6

340,6

347

400

8,8

406,4

388,8

377

500

11

508

486

DN

s

O.D

I.D

367 429

483 577

340 395

178 216

305 361

24 26

62 68

126 158

152 178

178 223

431 519

102 127

8xM20 12xM20

200x150 250x200

25 27

200x125 250x150

40 52

200x100 250x125

52 67

525

711

445

254

457

26

68

189

203

267

646

152

12xM20

300x250

25

300x200

52

300x150

78

601

812

505

279

533

26

68

221

330

313

754

165

16xM20

350x300

16

350x250

41

350x200

68

682

915

565

305

610

26

72

253

356

358

863

178

16xM24

400x350

51

400x300

41

400x250

68

456

837

1143

670

381

762

28

75

316

508

447

1078

229

20xM24

500x400

51

500x350

76

500x300

92

A

B

C

D

E

F

G

H

K

L

N

P.R

W

Bolts

Red

M

Red

M

Red

M

T

PN 16

90

S

10

1,8

17,2

13,6

14

35

15

2

21,3

17,3

60

63

53

95

25

28

14

35

12

38

17

40

25

4XM12

4xM12 15x10

2

20

2,3

26,9

22,3

67

67

58

105

29

29

16

38

12

38

17

41

25

4XM12

20x15

3

20x10

5

25

2,6

33,7

28,5

76

76

76

115

38

38

16

38

16

50

23

54

38

4XM12

25x20

3

25x15

6

32

2,6

42,4

37,2

88

88

96

140

48

48

16

40

20

50

28

68

38

4XM16

32x20

4

32x20

8

32x15

11

40

2,6

48,3

43,1

99

99

114

150

57

57

16

42

24

64

34

81

38

4XM16

40x32

3

40x25

7

40x20

11

50

2,9

60,3

54,5

109

121

140

165

64

76

18

45

32

76

45

108

38

4XM16

50x40

6

50x32

9

50x25

13

65 80

2,9 3,2

76,1 88,9

70,3 82,5

121 136

140 164

171 200

185 200

76 86

95 114

18 20

45 50

39 47

90 90

55 68

134 161

38 51

4XM16 8XM16

65x50 80x65

6 6

65x40 80x50

14 14

65x32 80x40

17 20

100

3,6

114,3

107,1

157

204

257

220

105 152

20

52

63

100

89

215

64

8XM16

100x80

13

100x65

19

100x50

27

125

4

139,7

131,7

179

245

314

250

124 190

22

55

79

127

112

269

76

8XM16

125x100

13

125x80

25

125x65

32

150

4,5

168,3

159,3

198

284

372

285

143

229

22

55

95

140

134

324

89

8XM20

150x125

14

150x100

27

150x80

40

200

6,3

219,1

206,5

240

367

483

340

178

305

24

62

126

152

178

431

102

12XM20

200x150

25

200x125

40

200x100

52

250

6,3

273

260,4

286

451

597

405

216

381

26

70

158

178

223

539

127

12XM24

250x200

27

250x150

52

250x125

67

300

7,1

323.9

309,7

332

535

711

460

254

457

26

78

189

203

267

646

152

12XM24

300x250

25

300x200

52

300x150

78

350

8

356,6

340,6

361

616

813

520

279

534

30

82

221

330

313

755

165

16XM24

350x300

18

350x250

41

350x200

88

400

8,8

406,4

388,8

390

695

915

580

305

610

32

85

253

355

358

863

178

16XM27

400x350

51

400x300

41

400x250

88

500

11

508

486

471

852

1143

715

381

762

36

90

316

508

447

1078

229

20XM30

500x400

51

500x350

76

500x300

92

NOTES: 1. ALL ELBOWS ARE 1.5 x OD AS PER DIN2605 2. ALL FITTING DIMENSIONS AS PER DIN 2448,DIN 2527,DIN 2615,DIN 2616,DIN 2617,DIN 2632 & DIN 2633 3. ALL BUILT UP DIMENSIONS ARE EXCLUDING ROOT CAP.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

BAA Checked

PIPING HANDBOOK

SHT.

BUILT-UP DIM. FITTINGS AND FLANGES -DIN

1 OF 3

Description

Doc. No : 30101-30-17D-306 C:\webpage\piping_std\30101-30-17D-306.doc

Approved REV. 0

DN

s

O.D

I.D

A

B

C

D

E

F

G

H

K

L

N

T 10 -

P.R

W

Bolts

Red

M

Red

M

Red

M

102 127

12xM24 12xM27

200x150 250x200

25 27

200x125 250x150

40 52

200x100 250x125

52 67

S

SEE TABLE PN 40

150

PN 25

200 250

6,3 7,1

219,1 273

206,5 258,8

258 304

385 469

483 597

360 425

178 216

305 381

30 32

80 88

126 158

152 178

178 223

300

8

323.9

307,9

346

549

711

485

254

457

34

92

189

203

267

646

152

16xM27

300x250

25

300x200

52

300x150

78

350

8

356,6

340,6

379

633

812

555

279

533

38

100

221

330

313

754

165

16xM30

350x300

16

350x250

41

350x200

68

400

8,8

406,4

388,8

415

720

915

620

305

610

40

110

253

355

368

863

178

16xM33

400x350

51

400x300

41

400x250

68

500

11

508

486

506

887

1143

730

381

762

45

125

316

508

447

1078

229

20xM33

500x400

51

500x350

76

500x300

92

DN

s

O.D

I.D

A

B

C

D

E

F

G

H

K

L

N

P.R

W

Bolts

Red

M

Red

M

Red

M

T

PN 40

90

431 539

S

10

1,8

17,2

13,6

16

35

15

2

21,3

17,3

63

66

53

95

25

28

16

38

12

38

17

40

25

4xM12

15x10

2

20

2,3

26,9

22,3

68

69

57

105

28

29

18

40

12

38

17

41

25

4xM12

20x15

3

20x10

5

25

2,6

33,7

28,5

78

78

76

115

38

38

18

40

16

50

23

54

38

4xM12

25x20

3

25x15

6

32

2,6

42,4

37,2

90

90

96

140

48

48

18

42

20

50

28

68

38

4xM16

32x20

4

32x20

8

32x15

11

40

2,6

48,3

43,1

102

102

114

150

57

57

18

45

24

64

34

81

38

4xM16

40x32

3

40x25

7

40x20

11

50

2,9

60,3

54,5

112

124

140

165

64

76

20

48

32

76

45

108

38

4xM16

50x40

6

50x32

9

50x25

13

65 80

2,9 3,2

76,1 88,9

70,3 82,5

128 144

147 172

171 200

185 200

76 86

95 114

22 24

52 58

39 47

90 90

55 68

134 161

38 51

8xM16 8xM16

65x50 80x65

6 6

65x40 80x50

14 14

65x32 80x40

17 20

100

3,6

114,3

107,1

170

217

257

235

105 152

24

65

63

100

89

215

64

8xM20

100x80

13

100x65

19

100x50

27

125

4

139,7

131,7

192

258

314

270

124 190

26

68

79

127

112

269

76

8xM24

125x100

13

125x80

25

125x65

32

150

4,5

168,3

159,3

218

304

372

300

143

28

75

95

140

134

324

89

8xM24

150x125

14

150x100

27

150x80

40

200

6,3

219,1

206,5

266

393

483

375

178

305

34

88

126

152

178

431

102

12xM27

200x150

25

200x125

40

200x100

52

250

7,1

273

258,8

321

486

597

450

216

381

38

105

158

178

223

539

127

12xM30,

250x200

27

250x150

52

250x125

67

300

8

323,9

307,9

369

572

711

515

254

457

42

115

189

203

267

646

152

16xM30

300x250

25

300x200

52

300x150

78

350

8,8

356,6

339

404

659

813

580

279

534

46

125

221

330

313

755

165

16xM33

350x300

18

350x250

41

350x200

88

400

11

406,4

384,4

440

745

915

660

305

610

50

135

253

355

358

863

178

16xM36

400x350

51

400x300

41

400x250

88

500

14,2

508

479,6

521

902

1143

755

381

762

56

140

316

508

447

1078

229

20xM39

500x400

51

500x350

76

500x300

92

229

4xM12

NOTES: 1. ALL ELBOWS ARE 1.5 x OD AS PER DIN2605 2. ALL FITTING DIMENSIONS AS PER DIN 2448,DIN 2527,DIN 2615,DIN 2616,DIN 2617,DIN 2632 & DIN 2633 3. ALL BUILT UP DIMENSIONS ARE EXCLUDING ROOT CAP.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

BAA Checked

PIPING HANDBOOK

SHT.

BUILT-UP DIM. FITTINGS AND FLANGES -DIN

2 OF 3

Description

Doc. No : 30101-30-17D-306 C:\webpage\piping_std\30101-30-17D-306.doc

Approved REV. 0

DN

s

O.D

I.D

A

B

C

D

E

F

G

H

K

L

N

T 10 -

P.R

W

Bolts

Red

M

Red

M

Red

M

S

SEE TABLE PN 100

40

PN 64

50

2,9

60,3

54,5

126

138

140

180

64

76

26

62

32

76

45

108

38

4xM20

50x40

6

50x32

9

50x25

13

65

3,2

76,1

69,7

144

163

171

205

76

95

26

68

39

90

55

134

38

8xM20

65x50

6

65x40

14

65x32

17

80 100

3,6 4

88,9 114,3

81,7 106,3

158 183

186 230

200 257

215 250

86 114 105 152

28 30

72 78

47 63

90 100

68 89

161 215

51 64

8xM20 8xM24

80x65 100x80

6 13

80x50 100x65

14 19

80x40 100x50

20 27

125

4,5

139,7

130,7

212

278

314

295

124 190

34

88

79

127

112

269

76

8xM27

125x100

13

125x80

25

125x65

32

150

5,6

168,3

157,1

238

324

372

345

143

229

36

95

95

140

134

324

89

8xM30

150x125

14

150x100

27

150x80

40

200

7,1

219,1

204,9

288

415

483

415

178

305

42

110

126

152

178

431

102

12xM33

200x150

25

200x125

40

200x100

52

250

8,8

273

255,4

341

506

597

470

216

381

46

125

158

178

223

539

127

12xM33

250x200

27

250x150

52

250x125

67

300

11

323.9

301,9

394

597

711

530

254

457

52

140

189

203

267

646

152

16xM33

300x250

25

300x200

52

300x150

78

350

12,5

356,6

331,6

429

683

812

600

279

533

56

150

221

330

313

754

165

16xM36

350x300

16

350x250

41

350x200

68

400

14,2

406,4

378

465

770

915

670

305

610

60

160

253

355

368

863

178

16xM39

400x350

51

400x300

41

400x250

68

DN

s

O.D

I.D

A

B

C

D

E

F

G

H

K

L

N

P.R

W

Bolts

Red

M

Red

M

Red

M

2

T

PN 100

100

S

10

1,8

17,2

13,6

20

45

15

2

21,3

17,3

70

73

53

105

25

28

20

45

12

38

17

40

25

4xM12

4xM12 15x10

25

2,6

33,7

28,5

96

96

76

140

38

38

24

58

16

50

23

54

38

4xM16

25x20

3

25x15

6

40

2,9

48,3

42,5

119

119

114

170

57

57

26

62

24

64

34

81

38

4xM20

40x32

3

40x25

7

40x20

11

50

3,2

60,3

53,9

132

144

140

195

64

76

28

68

32

76

45

108

38

4xM24

50x40

6

50x32

9

50x25

13

65 80

3,6 4

76,1 88,9

68,9 80,9

152 164

171 192

171 200

220 230

76 86

95 114

30 32

76 78

39 47

90 90

55 68

134 161

38 51

8xM24 8xM25

65x50 80x65

6 6

65x40 80x50

14 14

65x32 80x40

17 20

100

5

114,3

104,3

195

242

257

265

105 152

36

90

63

100

89

215

64

8xM27

100x80

13

100x65

19

100x50

27

125

6,3

139,7

127,1

229

295

314

315

124 190

40

105

79

127

112

269

76

8xM30

125x100

13

125x80

25

125x65

32

150

7,1

168,3

154,1

258

344

372

355

143

229

44

115

95

140

134

324

89

12xM30,

150x125

14

150x100

27

150x80

40

200

10

219,1

199,1

308

435

483

430

178

305

52

130

126

152

178

431

102

12xM33

200x150

25

200x125

40

200x100

52

250

12,5

273

248

373

538

597

500

216

381

60

157

158

178

223

539

127

12xM36

250x200

27

250x150

52

250x125

67

300

14,2

323.9

295,5

424

627

711

585

254

457

68

170

189

203

267

646

152

16xM39

300x250

25

300x200

52

300x150

78

350

16

356,6

324,6

468

723

813

655

279

534

74

189

221

330

313

755

165

16xM45

350x300

18

350x250

41

350x200

88

NOTES: 1. ALL ELBOWS ARE 1.5 x OD AS PER DIN2605 2. ALL FITTING DIMENSIONS AS PER DIN 2448,DIN 2527,DIN 2615,DIN 2616,DIN 2617,DIN 2632 & DIN 2633 3. ALL BUILT UP DIMENSIONS ARE EXCLUDING ROOT CAP.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

BAA Checked

PIPING HANDBOOK

SHT.

BUILT-UP DIM. FITTINGS AND FLANGES -DIN

3 OF 3

Description

Doc. No : 30101-30-17D-306 C:\webpage\piping_std\30101-30-17D-306.doc

Approved REV. 0

Dimensions according to DIN 2615 Teil2 N o m ina l P ip e S ize 1 5 x 15 x 15 1 5 x1 5 x 10 2 0 x 20 x 20 2 0 x 20 x 15 2 0x 2 0 x 10

29 29 29

29 29 29

2 5 x 25 x 25 2 5 x 25 x 25 2 5 x 25 x 25

38 38 38

38 38 38

32 32 32 32

x3 2 x3 2 x3 2 x3 2

x x x x

32 32 32 32

48 48 48 48

48 48 48 48

40 40 40 40

x4 0 x4 0 x4 0 x4 0

x x x x

40 40 40 40

57 57 57 57

57 57 57 57

50 50 50 50 50

x x x x x

50 50 50 50 50

x x x x x

50 40 32 25 20

64 64 64 64 64

64 60 57 51 44

65 65 65 65 65

x x x x x

65 65 65 65 65

x x x x x

65 50 40 32 25

76 76 76 76 76

76 70 67 64 57

80 80 80 80 80

x x x x x

80 80 80 80 80

x x x x x

80 65 50 40 32

86 86 86 86 86

86 83 76 73 70

10 5 10 5 10 5 10 5 10 5

1 05 98 95 89 88

1 00 1 00 1 00 1 00 1 00

0 Rev.

C e ntre to e nd R u n O u tlet C M 25 25 25 25

x x x x x

1 00 1 00 1 00 1 00 1 00

01/2002 Date

x x x x x

10 0 10 0 10 0 10 0 10 0

1 00 1 00 1 00 1 00 1 00

N o m in al P ip e S ize x 10 0 x 10 0 x 10 0 x 10 0 x 10 0 x 10 0 x 10 0 x 10 0 x 10 0 x 10 0

1 25 1 25 1 25 1 25 1 25

x x x x x

12 5 12 5 12 5 12 5 12 5

x x x x x

12 5 10 0 80 65 50

12 4 12 4 12 4 12 4 12 4

12 4 11 7 11 1 10 8 10 5

1 50 1 50 1 50 1 50 1 50

x x x x x

15 0 15 0 15 0 15 0 15 0

x x x x x

15 0 12 5 10 0 80 65

14 3 14 3 14 3 14 3 14 3

14 3 13 7 13 0 12 4 12 1

2 00 2 00 2 00 2 00 2 00

x x x x x

20 0 20 0 20 0 20 0 20 0

x x x x x

20 0 15 0 12 5 10 0 80

17 8 17 8 17 8 17 8 17 8

17 8 16 8 16 2 15 6 15 2

2 50 2 50 2 50 2 50 2 50

x x x x x

25 0 25 0 25 0 25 0 25 0

x x x x x

25 0 20 0 15 0 12 5 10 0

21 6 21 6 21 6 21 6 21 6

21 6 20 3 19 4 19 1 18 4

3 00 3 00 3 00 3 00 3 00

x x x x x

30 0 30 0 30 0 30 0 30 0

x x x x x

30 0 25 0 20 0 15 0 12 5

25 4 25 4 25 4 25 4 25 4

25 4 24 1 22 9 21 9 21 6

3 50 3 50 3 50 3 50 3 50

x x x x x

35 0 35 0 35 0 35 0 35 0

x x x x x

35 0 30 0 25 0 20 0 15 0

27 9 27 9 27 9 27 9 27 9

27 9 27 0 25 7 24 8 23 8

First Issue Description

C en tre to e nd R un O u tlet C M 10 5 10 5 10 5 98 10 5 95 10 5 89 10 5 88

40 0 40 0 40 0 40 0 40 0 40 0

N o m in al P ipe S ize x 40 0 x 40 0 x 40 0 x 35 0 x 40 0 x 30 0 x 40 0 x 25 0 x 40 0 x 20 0 x 40 0 x 15 0

45 0 45 0 45 0 45 0 45 0 45 0

x x x x x x

45 0 45 0 45 0 45 0 45 0 45 0

x x x x x x

45 0 40 0 35 0 30 0 25 0 20 0

3 43 3 43 3 43 3 43 3 43 3 43

34 3 33 0 33 0 32 1 30 8 29 8

50 0 50 0 50 0 50 0 50 0 50 0 50 0

x x x x x x x

50 0 50 0 50 0 50 0 50 0 50 0 50 0

x x x x x x x

50 0 45 0 40 0 35 0 30 0 25 0 20 0

3 81 3 81 3 81 3 81 3 81 3 81 3 81

38 1 36 8 35 6 35 6 34 6 33 3 32 4

60 0 60 0 60 0 60 0 60 0 60 0 60 0

x x x x x x x

60 0 60 0 60 0 60 0 60 0 60 0 60 0

x x x x x x x

60 0 50 0 45 0 40 0 35 0 30 0 25 0

4 32 4 32 4 32 4 32 4 32 4 32 4 32

43 2 43 2 41 9 40 6 40 6 39 7 38 4

70 0 70 0 70 0 70 0 70 0 70 0 70 0

x x x x x x x

70 0 70 0 70 0 70 0 70 0 70 0 70 0

x x x x x x x

70 0 60 0 50 0 45 0 40 0 35 0 30 0

5 21 5 21 5 21 5 21 5 21 5 21 5 21

52 1 50 8 48 3 47 0 45 7 45 7 44 8

80 0 80 0 80 0 80 0 80 0 80 0

x x x x x x

80 0 80 0 80 0 80 0 80 0 80 0

x x x x x x

80 0 70 0 60 0 50 0 45 0 40 0

5 97 5 97 5 97 5 97 5 97 5 97

59 7 57 2 55 9 53 3 52 1 50 8

LEA Prepared

PIPING HANDBOOK BW TEES DIN Doc. No : 30101-30-17D-307 C:\webpage\piping_std\30101-30-17D-307.doc

C en tre to e nd R un O utle t C M 3 05 30 5 3 05 30 5 3 05 29 5 3 05 28 3 3 05 27 3 3 05 26 4

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF PARTS OF ELBOWS-DIN Doc. No : 30101-30-17D-308 C:\webpage\piping_std\30101-30-17D-308.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

WN FLANGE PN10 DIN 2632

Pipe Size DN 10 175 200 250 300 350 400 500 600 700 800 900 1000

0 Rev.

Weigth d1

D

b

b

b

WN

SO

BLD

k

h1 d3

s

r

d4

f

Bolts

d2 kg

SEE DIN 2633 219 273 324 356 406 508 610 711 813 914 1016

340 395 445 505 565 670 780 895 1015 1115 1230

01/2002 Date

24 26 26 26 26 28 28 30 32 34 34

24 26 26 28 32 38

24 26 26 26 26 28

295 350 400 460 515 620 725 840 950 1050 1160

62 68 68 68 72 75 80 80 90 95 95

235 292 344 385 440 542 642 745 850 950 1052

5,9 6,3 7,1 7,1 7,1 7,1 7,1 8 8 10 10

10 12 12 12 12 12 12 12 12 12 16

268 320 370 430 482 585 685 800 905 1005 1110

First Issue Description

3 3 4 4 4 4 5 5 5 5 5

8 12 12 16 16 20 20 24 24 28 28

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

x x x x x x x x x x x

M 20 M 20 M 20 M 20 M 24 M 24 M 27 M 27 M 30 M 30 M 33

BAA Checked SHT.

1 OF 8

22 22 22 22 26 26 30 30 33 33 36

11,3 14,7 17,6 21,4 26,1 34,7 42,2 58,7 80 95,6 11,5

Approved REV. 0

WN FLANGE PN10 DIN 2633

Pipe Size DN 10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000

0 Rev.

Weigth d1 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114 140 168 219 273 324 356 406 508 610 711 813 914 1016

01/2002 Date

D 90 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 715 840 910 1025 1125 1230

b

b

b

WN

SO

BLD

14 14 16 16 16 16 18 18 20 20 22 22 24 26 26 26 26 28 28 30 32 34 34

14 14 16 16 16 16 18 18 20 20 22 22 24 26 26 28 32 38

14 14 16 16 16 16 18 18 20 20 22 22 24 26 26 26 26 28

k 60 65 75 85 100 110 125 145 160 180 210 240 295 350 400 460 515 620 725 840 950 1050 1160

h1 d3 35 35 38 38 40 42 45 45 50 52 55 55 62 68 68 68 72 75 80 80 90 95 95

25 32 40 45 56 64 75 90 105 125 156 184 235 292 344 385 440 542 642 745 850 950 1052

s

r

d4

f

1,8 2 2,3 2,6 2,6 2,6 2,9 2,9 3,2 3,6 4 4,5 5,9 6,3 7,1 7,1 7,1 7,1 7,1 8 8 10 10

4 4 4 4 6 6 6 6 8 8 8 10 10 12 12 12 12 12 12 12 12 12 16

40 45 58 68 78 88 102 122 138 158 188 212 268 320 378 438 490 610 725 795 900 1000 1115

2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 5 5 5 5 5

First Issue Description

Bolts

d2

x x x x x x x x x x x x x x x x x x x x x x x

kg 14 0,58 14 0,648 14 0,952 14 1,14 18 1,69 18 1,86 18 2,53 18 3,06 18 3,7 18 4,62 18 6,3 23 7,75 23 11 27 15,6 27 22 27 31,2 30 28,8 33 39,3 36 75,4 36 77 39 101 39 122 42 162

4 4 4 4 4 4 4 4 4 8 8 8 12 12 12 16 16 20 20 24 24 28 28

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

M 12 M 12 M 12 M 12 M 16 M 16 M 16 M 16 M 16 M 16 M 16 M 20 M 20 M 24 M 24 M 24 M 27 M 30 M 33 M 33 M 36 M 36 M 39

BAA Checked SHT.

2 OF 8

Approved REV. 0

WN FLANGE PN10 DIN 2634

Pipe Size DN 10 150 200 250 300 350 400 500 600 700 800 900 1000

0 Rev.

d1

D

b

b

WN

BLD

k

h1

d3

s

r

d4

f

10 12 12 12 12 12 12 12 12 12 16

278 335 395 450 505 615 720 820 930 1030 1140

3 3 4 4 4 4 5 5 5 5 5

Bolts

d2

x x x x x x x x x x x

26 30 30 33 36 36 39 42 48 48 56

SEE DIN 2635 219 273 324 356 406 508 610 711 813 914 1016

360 425 485 555 620 730 845 960 1085 1185 1320

01/2002 Date

30 32 34 38 40 44 46 46 50 54 58

30 32 34 38 40 45

310 370 430 490 550 660 770 875 990 1090 1210

80 244 6,3 88 298 7,1 92 352 8 100 398 8 110 452 8,8 125 558 10 125 660 11 125 760 12,5 135 865 14,2 145 968 16 155 1070 17,5

First Issue Description

12 12 16 16 16 20 20 24 24 28 28

M 24 M 27 M 27 M 30 M 33 M 33 M 36 M 39 M 45 M 45 M 52

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

BAA Checked SHT.

3 OF 8

Approved REV. 0

FLANGE PN 40 DIN 2635

Pipe Size DN 10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500

0 Rev.

Weigth d1

D

17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114 140 168 219 273 324 356 406 508

90 95 105 115 140 150 165 185 200 235 270 300 375 450 515 580 660 755

01/2002 Date

b

b

WN

BLD

16 16 18 18 18 18 20 22 24 24 26 28 34 38 42 46 50 52

16 16 18 18 18 18 20 22 24 24 26 28 34 38 42 46 50 56

k

h1

d3

s

r

d4

f

60 65 75 85 100 110 125 145 160 190 220 250 320 385 450 510 585 670

35 38 40 40 42 45 48 52 58 65 68 75 88 105 115 125 135 140

28 32 40 46 56 64 75 90 105 134 162 192 244 306 362 408 462 562

1,8 2 2,3 2,6 2,6 2,6 2,9 2,9 3,2 3,6 4 4,5 6,3 7,1 8 8,8 11 14,2

4 4 4 4 6 6 6 6 8 8 8 10 10 12 12 12 12 12

40 45 58 68 78 88 102 122 138 162 188 218 285 345 410 465 535 615

2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4

First Issue Description

4 4 4 4 4 4 4 8 4 8 8 8 12 12 16 16 16 20

Bolts

d2

x x x x x x x x x x x x x x x x x x

kg 14 0,661 14 0,746 14 1,06 14 1,29 18 1,88 18 2,33 18 2,82 18 3,74 18 4,75 23 6,52 27 9,07 27 11,8 30 21,5 33 34,9 33 49,7 36 68,1 39 96,5 42 117

M 12 M 12 M 12 M 12 M 16 M 16 M 16 M 16 M 16 M 20 M 24 M 24 M 27 M 30 M 30 M 33 M 36 M 39

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

BAA Checked SHT.

4 OF 8

Approved REV. 0

WN FLANGE PN64 DIN2636

Pipe Size d 1 DN 10 40 50 60,3 65 76,1 80 88,9 100 114 125 140 150 168 200 219 250 273 300 324 350 356 400 406

0 Rev.

01/2002 Date

Weigth D

b

b

WN

BLD

k

h1

d3

s

r

d4

f

Bolts

d2 kg

SEE DIN 2637 180 205 215 250 295 345 415 470 530 600 670

26 26 28 30 34 36 42 46 52 56 60

26 26 28 30 34 36 42 46 52 56 60

135 160 170 200 240 280 345 400 460 525 585

62 68 72 78 88 95 110 125 140 150 160

102 122 138 162 188 218 285 345 410 465 535

2,9 3,2 3,6 4 4,5 5,6 7,1 8,8 11 12,5 14,5

6 6 8 8 8 10 10 12 12 12 12

102 122 138 162 188 218 285 345 410 465 535

First Issue Description

3 3 3 3 3 3 3 3 4 4 4

4 8 8 8 8 8 12 12 16 16 16

x x x x x x x x x x x

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

M 20 M 20 M 20 M 24 M 27 M 30 M 33 M 33 M 33 M 36 M 39

BAA Checked SHT.

5 OF 8

22 22 22 26 30 33 36 36 36 39 42

4,55 5,73 6,69 9,66 15,1 21,9 34,9 49,6 68,7 94,6 124

Approved REV. 0

WN FLANGE PN100 DIN 2637

Pipe Size DN 10 15 25 32 40 50 65 80 100 125 150 200 250 300 350

0 Rev.

Weigth d1 17,2 21,3 33,7 42,4 48,3 60,3 76,1 88,9 114 140 168 219 273 324 356

01/2002 Date

D 100 105 140 155 170 195 220 230 265 315 355 430 505 585 655

b

b

WN

BLD

20 20 24 24 26 28 30 32 36 40 44 52 60 68 74

20 20 24 24 26 26 26 28 30 34 36 40 46 52 56

h1

d3

s

r

d4

f

45 45 58 60 62 68 76 78 90 105 115 130 157 170 189

32 34 52 62 70 90 108 120 150 180 210 278 340 400 460

1,8 2 2,6 2,6 2,9 3,2 3,6 4 5 6,3 7,1 10 12,5 14,2 16

4 4 4 6 6 6 6 8 8 8 10 10 12 12 12

40 45 68 75 88 102 122 138 162 188 218 285 345 410 465

2 2 2 2 3 3 3 3 3 3 3 3 3 4 4

Bolts 4 x 4 x 4 x 4 x 4 x 4 x 8 x 8 x 8 x 8 x 12 x 12 x 12 x 16 x 16 x

First Issue Description

M 12 M 12 M 16 M 20 M 20 M 24 M 24 M 24 M 27 M 30 M 30 M 33 M 36 M 39 M 45

d2 14 14 18 23 22 26 26 26 30 33 33 36 39 42 45

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

kg 1,09 1,19 2,66 3,2 4,09 5,98 7,91 8,95 13,7 22,7 30,2 52,8 81,4 122 165

BAA Checked SHT.

6 OF 8

Approved REV. 0

WN FLANGE PN160 DIN 2638

Pipe Size DN 10 15 25 40 50 65 80 100 125 150 200 250 300

Weigth d1 17,2 21,3 33,7 48,3 60,3 76,1 88,9 114 140 168 219 273 324

D 100 105 140 170 195 220 230 265 315 355 430 515 585

b

b

h1

WN

BLD

20 20 24 28 30 34 36 40 44 50 60 68 78

20 20 24 28 30 34 36 40 44 50 60 68 78

45 45 58 64 75 82 86 100 115 128 140 155 175

d3 32 34 52 70 90 108 120 150 180 210 278 340 400

s

r

2 2 2,9 3,6 4 5 6,3 8 10 12,5 16 20 22,2

4 4 4 6 6 6 8 8 8 10 10 12 12

d4 40 45 68 88 102 122 138 162 188 218 285 345 410

f 2 2 2 3 3 3 3 3 3 3 3 3 4

Bolts 4 4 4 4 4 8 8 8 8 12 12 12 16

x x x x x x x x x x x x x

d2

M 12 M 12 M 16 M 20 M 24 M 24 M 24 M 27 M 30 M 30 M 33 M 39 M 39

14 14 18 22 26 26 26 30 33 33 36 42 42

kg 1,09 1,19 2,66 4,3 6,25 8,35 9,75 14,8 23 32,5 59,4 94,5 136

LPJ FLANGES PN10 DIN 2642 0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

BAA Checked SHT.

7 OF 8

Approved REV. 0

Pipe Size DN 10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800

0 Rev.

d1

D

d6

b

k

e

d5

17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 99,8 114 140 168 219 273 324 356 406 508 610 711 813

90 95 105 115 140 150 165 185 200 220 250 285 340 395 445 505 565 670 780 895 1015

19 24 30 36 46 54 65 81 94 119 145 173 225 279 329 374 426 517 618 721 824

14 14 14 16 16 16 16 16 18 18 18 18 20 22 26 28 32 38 44 50 56

60 65 75 85 100 110 125 145 160 180 210 240 295 350 400 460 515 620 725 840 950

3 3 3 4 4 4 5 5 5 5 5 5 5 5 5 6 6 6 7 7 7

17,7 22 27,6 34,4 43,1 49 61,1 77,1 90,3 115,9 141,6 170,5 221,8 276,2 327,2 372,2 423,7 513,6 616,6 718,6 821,5

01/2002 Date

h3 d4 max 10 40 10 45 12 58 12 68 12 78 12 88 14 102 14 122 16 138 16 158 18 188 18 212 20 268 22 320 22 370 22 430 24 482 26 585 26 685 28 800 30 905

h4 min 9 9 12 15 15 17 23 23 23 28 30 30 30 30 35

s1 min 1,8 2 2 2 2,6 2,6 2,6 2,6 3,2 3,2 3,2 3,2 3,2 4 4

s2 min 3 3 3 3 3,5 3,5 3,5 3,5 4 4 4 4 4 5 5

r 3 3 3 4 4 4 5 5 5 5 5 5 5 5 5 6 6 6 7 7 7

First Issue Description

4 4 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20 20 24 24

Bolts

d2

x x x x x x x x x x x x x x x x x x x x x

14 14 14 14 18 18 18 18 18 18 18 22 22 22 22 22 26 26 30 30 33

M 12 M 12 M 12 M 12 M 16 M 16 M 16 M 16 M 16 M 16 M 16 M 20 M 20 M 20 M 20 M 20 M 24 M 24 M 27 M 27 M 30

LEA Prepared

PIPING HANDBOOK DIMENSIONS OF DIN FLANGES Doc. No : 30101-30-17D-309 C:\webpage\piping_std\30101-30-17D-309.DOC

Weigth FLg Retain'g kg ring 0,599 0,087 0,689 0,105 0,806 0,203 1,11 0,276 1,64 0,343 1,86 0,426 2,2 0,618 2,62 0,786 3,32 1,1 3,67 1,31 4,54 1,96 5,6 2,18 7,46 3,1 10,3 4,22 14 4,85 18,5 6,71 25 8,28 37 11,5 56,3 15,6 80,4 23,2 113,2 29,2

BAA Checked SHT.

8 OF 8

Approved REV. 0

Pipe Size DN 10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500 Pipe Size

No 4 4 4 4 4 4 4 4 4 4 8 8 8 12 12 12 16 20

DN 10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500

No 4 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20

ND 6 Bolts Dia L1 M 10 40 M 10 40 M 10 45 M 10 45 M 12 45 M 12 45 M 12 45 M 12 45 M 16 55 M 16 55 M 16 55 M 16 55 M 16 60 M 16 65 M 20 70 M 20 70 M 20 65 M 20 75 ND 40 Bolts Dia L1 M 12 50 M 12 50 M 12 55 M 12 55 M 16 55 M 16 55 M 16 60 M 16 65 M 16 70 M 20 75 M 24 80 M 24 85 M 27 100 M 30 110 M 30 120 M 33 130 M 36 140 M 39 145

L2

60 60 60 60 70 70 75 75 80 85 95 95 95 95

L2 65 65 70 70 75 75 80 85 90 95 110 115 130 145 155 170 185 195

No

ND 10 Bolts Dia L1

L2

No

M 20 M 20 M 20 M 20 M 24 M 24 ND 64 Bolts Dia

75 75 75 75 80 85

95 100 100 100 110 115

L2

No 4 4 4

M 16

90

4

M 16

90

4

M 20

105

4 4 8 8 8 8 12 12 12 16 16

M 20 M 24 M 24 M 24 M 27 M 30 M 30 M 33 M 36 M 39 M 45

10 115 120 120 135 150 160 180 205 225 250

4 4 8 8 8 8 12 12 12 16

M 20 M 24 M 24 M 24 M 27 M 30 M 30 M 33 M 39 M 39

110 120 125 130 145 160 170 195 225 245

4 8 8 8 8 12 12 12 16

M 24 M 24 M 24 M 27 M 30 M 30 M 33 M 39 M 45

125 135 140 155 180 190 215 260 305

SEE ND100

4 8 8 8 8 8 12 12 16 16 16

M 20 M 20 M 20 M 24 M 27 M 30 M 33 M 33 M 33 M 36 M 39

100 100 105 120 130 145 160 170 180 185 210

L2 70 70

L2 60 60 65 85 70 70 75 75 80 80 85 95 95 110 115 120 130 140 ND 160 Bolts No Dia 4 M 12 4 M 12

No

ND 25 Bolts Dia L1

No 4 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 ND 100 Bolts Dia M 12 M 12

SEE ND 16

8 12 12 16 16 20

ND 16 Bolts Dia L1 M 12 45 M 12 45 M 12 50 M 12 50 M 16 55 M 16 55 M 16 55 M 16 55 M 16 60 M 16 60 M 16 65 M 20 70 M 20 75 M 24 80 M 24 85 M 24 90 M 27 95 M 30 110

L2

SEE ND 40

12 12 16 16 16 20

L2 70 70

M 24 M 27 M 27 M 30 M 33 M 33

90 95 100 110 120 130 ND 250 Bolts No Dia 4 M 16 4 M 16

120 130 130 145 155 165

L2 90 90

Note : Dimensions are including 2 mm gasket thickness.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK BOLTS FOR DIN FLANGES Doc. No : 30101-30-17D-310 C:\webpage\piping_std\30101-30-17D-310.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK FLANGED DIN VALVES UP/TO PN250 Doc. No : 30101-30-17D-320 C:\webpage\piping_std\30101-30-17D-320.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK FLANGED DIN VALVES UP/TO PN250 Doc. No : 30101-30-17D-320 C:\webpage\piping_std\30101-30-17D-320.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

Piping Stress Review Criteria 1. Scope This design aid provides guidance for determining what lines on a project shall require review by the pipe stress engineer. The following criteria listed are not intended to be all inclusive and each project should be reviewed with the pipe stress engineer to identify any other special situations that should be reviewed. All lines on a project that meet any of the criteria below should be sent to the pipe stress engineer for review. The pipe stress engineer shall decide which lines will require a full stress analysis and which lines can be deemed to be adequate by other suitable means. 2. Design aid

0 Rev.

2.1

Lines 2” and smaller operating above

200 degrees C.

2.2

Lines 3”, 4” and 6” operating above

150 degrees C

2.3

Lines 8” and larger operating above

93 degrees C

2.4

Lines 24” and lager.

2.5

All lines operating below 10 degrees C, which require special “cold” supports.

2.6

All lines connected to rotating equipment such as pumps, compressors, steam turbines, and etc.

2.7

All lines connected to vessels on weigh cells.

2.8

All jacketed lines

2.9

Lines connected to air cooled heat exchangers (fin fans).

2.10

Piping systems, which are attached to equipment nozzles with large displacements.

2.11

Lines with spans outside the pipe span tables.

2.12

Lines located in pipe racks having exceptional length.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK PIPING STRESS REVIEW CRITERIA Doc. No : 30101-30-17D-400 C:\webpage\piping_std\30101-30-17D-400.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

0 Rev.

2.13

At extreme; heavy valves, unusual branches, change of direction, additional forces, i.e., at PSV’s, reducing valves, etc.

2.14

All reinforced thermoset FRP (fibre reinforced pipe) piping systems operating above 65 degrees C.

2.15

All piping systems connected to FRP, plastic, glass lined steel or brittle equipment.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK PIPING STRESS REVIEW CRITERIA Doc. No : 30101-30-17D-400 C:\webpage\piping_std\30101-30-17D-400.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

Pipe Size O.D. in mm inch. 2

60,3

3

88,9

4

114,3

5

141,3

6

168,3

8

219,1

10

273,1

12

323,9

MAX. ALLOW. SPAN BARE PIPE 0 Sch 20 C 1010C m 10S 4,1 40 4,25 80 4,3 10S 5,5 40 5,8 80 5,9 10S 6,6 40 7 80 7,1 10S 7,75 40 8,2 80 8,3 10S 8,75 40 9,3 80 9,4 10S 10,6 20 11,1 30 11,2 40 11,25 80 11,35 10S 12,4 20 12,8 30 13 40 13,1 80 13,2 10S 14,1 20 14,5 30 14,7 40 14,85 80 15 20 15,6

1010C 2000C m 4,1 4,25 4,3 5,5 5,8 5,9 6,6 7 7,1 7,75 8,2 8,3 8,75 9,3 9,4 10,6 11,1 11,2 11,25 11,35 12,4 12,8 13 13,1 13,2 14 14,5 14,7 14,85 15 15,6

2010C 3000C m 4,1 4,25 4,3 5,5 5,8 5,9 6,6 7 7,1 7,75 8,2 8,3 8,75 9,3 9,4 10,6 11,1 11,2 11,25 11,35 12,1 12,8 13 13,1 13,2 13,5 14 14,35 14,6 14,7 15

3010C 4000C m 4,1 4,25 4,3 5,5 5,8 5,9 6,6 7 7,1 7,75 8,2 8,3 8,3 9 9,25 9,75 10,3 10,8 10,5 10,75 10,95 11,6 11,8 11,9 12,1 12,15 12,7 13 13,15 13,3 13,6

MAX. ALLOW. SPAN PIPE + INS.

200C 1010C m 3,7 3,9 4 5,1 5,5 5,6 6 6,5 6,7 7,1 7,85 7,9 8,1 8,8 9,1 9,8 10,7 10,6 10,7 11 11,5 12,1 12,4 12,6 12,9 13 13,6 14 14,2 14,5 14,8

1010C 2000C m 3,7 3,9 4 5,1 5,5 5,6 6 6,5 6,7 7,1 7,85 7,9 8,1 8,8 9,1 9,8 10,7 10,6 10,7 11 11,2 12,1 12,4 12,6 12,9 12,4 13,25 13,85 14,15 14,5 14,5

2010C 3000C m 3,7 3,9 4 5,1 5,5 5,6 6 6,5 6,7 7,1 7,85 7,9 8,1 8,8 9,1 9,4 10,4 10,6 10,7 11 10,75 11,7 12,1 12,25 12,7 11,9 12,7 13,2 13,55 14 13,85

3010C 4000C m 3,7 3,9 4 5 5,5 5,6 5,7 6,5 6,7 6,6 7,4 7,7 7,3 8,35 8,7 8,55 9,4 9,6 9,7 10,1 9,75 10,6 10,9 11 11,5 10,75 11,5 12 12,3 12,7 12,5

MAX. ALLOW. PIPE SPAN PIPE + W MAX. ALLOW. PIPE SPAN. + W+ INS

200C 1010C m 3,75 3,95 4,1 4,85 5,3 5,5 5,6 6,3 6,55 6,45 7,25 7,5 7,1 8,1 8,5 8 8,85 9,1 9,6 10,2 8,5 10 10,6 11 11,8 9,4 10,45 11,4 12,1 13,25 11,4

1010C 2000C m 3,75 3,95 4,1 4,85 5,3 5,5 5,6 6,3 6,55 6,45 7,25 7,5 6,9 8,1 8,5 7,6 8,85 9,1 9,5 10,2 8,3 9,5 10,1 10,5 11,7 8,9 9,9 10,8 11,5 12,8 10,85

2010C 3000C m 3,75 3,95 4,1 4,85 5,3 5,5 5,6 6,3 6,55 6,3 7,25 7,5 6,6 8,1 8,5 7,25 8,6 8,8 9,15 10 8 9,1 9,7 10,05 11,2 8,5 9,5 10,35 11 12,3 10,4

3010C 4000C m 3,75 3,95 4,1 4,7 5,3 5,5 5,1 6 6,55 5,7 6,75 7,2 6 7,35 8 6,6 7,8 8,1 8,2 9 7,2 8,25 8,7 9,1 10,1 7,7 8,6 9,4 9,9 11 9,4

200C 1010C m 3,45 3,7 3,9 4,6 5,1 5,3 5,3 6 6,3 6,1 7 7,1 6,75 7,8 8,3 7,6 8,35 8,6 8,95 9,9 8,35 9,55 10,4 10,6 11,5 8,9 10 11 11,5 13 11

1010C 2000C m 3,45 3,7 3,9 4,6 5,1 5,3 5,3 6 6,3 6,1 7 7,1 6,4 7,8 8,3 7,2 8,35 8,6 8,95 9,9 7,9 9,05 9,7 10,1 11,25 8,4 9,5 10,4 11 12,4 10,4

2010C 3000C m 3,45 3,7 3,9 4,6 5,1 5,3 5,2 6 6,3 5,85 7 7,1 6,15 7,7 8,3 6,9 8,1 8,4 8,7 9,65 7,55 8,65 9,3 9,65 10,75 8,1 9,05 10 10,5 11,9 10

3010C 4000C m 3,4 3,7 3,9 4,25 5 5,3 4,7 5,65 6,1 5,25 6,35 5,9 5,55 6,95 7,6 6,2 7,3 7,6 7,85 8,37 6,85 7,85 8,4 8,7 9,75 7,3 8,2 9 9,5 10,8 9

Spans are based on a maximum deflection of 1/600 length and on a bending stress of 30% of allowable stress.

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK MAX. ALLOWABLE PIPE SPANS Doc. No : 30101-30-17D-401 C:\webpage\piping_std\30101-30-17D-401.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

Pipe

MAX. ALLOW. SPAN BARE PIPE

Size O.D. in

mm

inch. 14

16

18

20

24

30

355,6

406,4

457

508

610

762

MAX. ALLOW. SPAN PIPE + INS.

MAX. ALLOW. PIPE SPAN PIPE + W MAX. ALLOW. PIPE SPAN. + W+ INS

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Sch 20 C 101 C 201 C 301 C 20 C 101 C 201 C 301 C 20 C 101 C 201 C 301 C 20 C 101 C 201 C 301 C 1010C 2000C 3000C 4000C 1010C 2000C 3000C 4000C 1010C 2000C 3000C 4000C 1010C 2000C 3000C 4000C

m

m

m

m

m

m

30

15,8

15,8

15,2

13,8

15,1

14,8

m

m

40

15,9

15,9

15,3

13,85

15,3

15

80

16

16

15,5

14

15,6

15,5

14,9 13,5

14,2 12,85 14,35

13

m

m

m

m

m

m

m

m

12,1

11,5

11

10

11,6

11

10,5

9,55

12,6

12

11,5

10,4

12,15

11,5

11

10

14,1

13,3

12,8

11,6

13,8

13,1

12,5

11,35

9,7

20

17,1

16,9

16,1

14,6

16,3

15,5

14,85 13,4

11,8

11,35

10,7

11,4

10,8

10,35

9,35

30

17,3

17,1

16,4

14,8

16,6

16

15,3 13,8

12,5

11,8

11,35 10,25 12,05

11,5

11

9,95

40

17,5

17,3

16,6

15

16,9

16,4

15,6 14,15 13,55 13,25

12,3

11,1

13,2

12,5

12

10,8

80

17,6

17,5

16,7

15,15

17,1

16,8

16,1 14,6

15,2

14,4

13,8

12,5

14,85

14,1

13,5

12,2

20

18,6

18

17,2

15,5

17,45 16,55 15,85 14,35

12,1

11,5

11

10

11,8

11,2

10,75

9,7

30

18,9

18,3

17,,6

15,9

18,15

17,2

16,5 14,95 13,5

12,85

12,3

11,15

13,1

12,4

11,9

10,8

40

19

18,55

17,8

15,1

18,4

17,6

16,8

15,2 14,5

13,75

13,2

11,9

14,1

13,35

12,8

11,6

80

19

18,65 17,85 16,15

18,7

17,95

17,2 15,55 16,1

15,3

14,6

13,2

15,7

14

14,25

12,9

20

20,2

19,3

18,45

17

18,95 17,95

17,2 15,55 13,3

12,6

12,1

10,95 12,85

12,2

30

20,4

19,55

18,7

16,9

19,6

18,5

17,8

16,1 14,4

13,7

13,1

11,8

14,1

13,45 12,85

11,6

40

20,1

19,7

18,8

17

19,8

18,7

18 16,25 15,1

14,3

13,7

12,4

14,8

14,1

13,45

12,2

20

22,2

21,2

20,3

18,35

21

19,9

19

17,2 13,8

13,05

12,5

11,3

13,4

12,7

12,2

11

30

22,8

21,6

20,7

18,75

21,8

20,6

19,75

17,9 15,6

14,85

14,2

12,85

15,3

14,5

13,9

12,6

40

23

21,8

20,8

18,85

22

20,9

20

18,1 16,5

15,7

15

13,6

16,2

15,35

14,7

13,35

20

25,6

24,4

23,3

21,1

24,4

23,1

22,1

20 15,85

15

14,4

13

15,6

14,8

14,15 12,85

30

25,8

24,4

23,4

21,2

24,7

23,4

22,4

20,3 16,9

16

15,35

13,9

16,7

15,8

15,2

11,65 10,55

13,7

Spans are based on a maximum deflection of 1/600 length and on a bending stress of 30% of allowable stress.

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK MAX. ALLOWABLE PIPE SPANS Doc. No : 30101-30-17D-401 C:\webpage\piping_std\30101-30-17D-401.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

Temperature1)

mm/m O

O

inch/100 feet

"A" + "B" 0 0,07 0,13 0,19

"C" 0 0,06 0,12 0,18

"D" 0 0,09 0,19 0,28

F 68 80 90 100

C 20 26,7 32,2 37,8

"A" + "B" 0 0,08 0,15 0,23

"C" 0 0,07 0,14 0,22

"D" 0 0,11 0,23 0,34

0,26 0,32 0,38 0,44 0,51

0,24 0,3 0,37 0,43 0,48

0,38 0,47 0,57 0,66 0,75

110 120 130 140 150

43,4 48,9 54,5 60 65,6

0,31 38 0,46 0,53 0,61

0,29 0,36 0,44 0,51 0,58

0,45 0,56 0,68 0,79 0,9

0,57 0,63 0,7 0,76 0,83

0,54 0,6 0,67 0,73 0,78

0,84 0,93 1,03 1,13 1,22

160 170 180 190 200

71,1 76,7 82,2 87,8 93,4

0,69 0,76 0,84 0,91 0,99

0,65 0,72 0,8 0,87 0,94

1,01 1,12 1,24 1,35 1,46

0,89 0,96 1,03 1,1 1,17

0,85 0,92 0,98 1,04 1,11

1,31 1,41 1,5 1,6 1,69

210 220 230 240 250

98,9 104,5 110 115,6 121,1

1,07 1,15 1,24 1,32 1,4

1,02 1,1 1,17 1,25 1,33

1,57 1,69 0,18 1,92 2,03

1,23 1,3 1,37 1,45 1,52

1,17 1,23 1,3 1,36 1,42

1,79 1,88 1,98 2,08 2,18

260 270 280 290 300

126,7 132,2 137,8 143,7 148,9

1,48 1,57 1,65 1,74 1,82

1,41 1,48 1,56 1,63 1,71

2,15 2,26 2,38 2,49 2,61

1,59 1,66 1,73 1,81 1,88

1,49 1,56 1,62 1,68 1,75

2,28 2,37 2,47 2,57 2,67

310 320 330 340 350

154,5 160 165,6 171,1 176,7

1,91 2 2,08 2,17 2,26

1,79 1,87 1,94 2,02 2,1

2,73 2,85 2,96 3,08 3,2

1,96 2,03 2,1 2,17 2,25

1,82 1,88 1,95 2,02 2,08

2,76 2,87 2,97 3,07 3,16

360 370 380 390 400

182,2 187,8 193,4 198,9 204,5

2,35 2,44 2,52 2,61 2,7

2,18 2,26 2,34 2,42 2,5

3,32 3,44 3,56 3,68 3,8

Materiaal "A" A- 53 A-120 A-210 A- 83 A-161 API 5L A-106 A-192 Koolstofstaal

Materiaal "B" A-335 P-1 P-12 P- 2 P-21 P-11 P-22 3 Cr,Mo en lager

Materiaal "C" A-335 P-5 P5b P-5c P-7 P-9 hoger dan 3 Cr Mo

Materiaal "D" A-240 A312 A-249 A-269 Cr Ni staal

Note : 1. Installation temperature based on 20 0C

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK COEFFICIENT OF EXPANSION Doc. No : 30101-30-17D-402 C:\webpage\piping_std\30101-30-17D-402.doc

BAA Checked SHT.

1 OF 4

Approved REV. 0

Temperatuur1)

mm/m O

O

inch/100 feet

"A" + "B" 2,32 2,4 2,49 2,56 2,63

"C" 2,16 2,22 2,3 2,37 2,44

"D" 3,27 3,37 3,48 3,56 3,68

F 410 420 430 440 450

C 210 215,6 221,1 226,7 232,2

"A" + "B" 2,79 2,88 2,98 3,07 3,16

"C" 2,59 2,67 2,76 2,84 2,93

"D" 3,92 4,04 4,17 4,29 4,41

2,71 2,78 2,87 2,94 3,02

2,51 2,58 2,65 2,72 2,79

3,78 3,88 3,97 4,08 4,17

460 470 480 490 500

237,8 243,4 248,9 254,5 260

3,25 3,34 3,44 3,53 3,62

3,01 3,1 3,18 3,27 3,35

4,53 4,65 4,77 4,89 5,01

3,1 3,18 3,26 3,34 3,42

2,87 2,94 3,02 3,09 3,16

4,28 4,38 4,48 4,58 4,68

510 520 530 540 550

265,6 271,1 276,7 281,2 287,8

3,72 3,82 3,91 4,01 4,11

3,44 3,53 3,62 3,71 3,8

5,13 5,25 5,38 5,5 5,62

3,51 3,59 3,67 3,75 3,83

3,24 3,32 3,38 3,46 3,53

4,78 4,89 4,99 5,1 5,2

560 570 580 590 600

293,4 298,9 304,5 310 315,5

4,21 4,31 4,4 4,5 4,6

3,89 3,98 4,06 4,15 4,24

5,74 5,87 5,99 6,12 6,24

3,92 4 4,09 4,17 4,26

3,61 3,68 3,76 3,84 3,91

5,31 5,41 5,51 5,62 5,73

610 620 630 640 650

321,1 326,7 332,2 337,8 343,4

4,7 4,8 4,91 5,01 5,11

4,33 4,42 4,51 4,6 4,69

6,37 6,49 6,62 6,74 6,87

4,34 4,43 4,52 4,61 4,69

3,98 4,06 4,13 4,21 4,28

5,83 5,93 6,04 6,14 6,25

660 670 680 690 700

348,9 354,5 360 365,6 371,1

5,21 5,32 5,42 5,53 5,63

4,78 4,87 4,96 5,05 5,14

7 7,12 7,25 7,37 7,5

4,78 4,87 4,96 5,04 5,13

4,37 4,44 4,53 4,6 4,68

6,36 6,47 6,57 6,67 6,79

710 720 730 740 750

376,7 382,2 387,8 393,4 398,9

5,74 5,84 5,95 6,05 6,16

5,24 5,33 5,43 5,52 5,62

7,63 7,76 7,89 8,02 8,15

Materiaal "A" A- 53 A-120 A-210 A- 83 A-161 API 5L A-106 A-192 Koolstofstaal

Materiaal "B" A-335 P-1 P-12 P- 2 P-21 P-11 P-22 3 Cr,Mo en lager

Materiaal "C" A-335 P-5 P5b P-5c P-7 P-9 hoger dan 3 Cr Mo

Materiaal "D" A-240 A312 A-249 A-269 Cr Ni staal

Note : 1. Installation temperature based on 20 0C

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK COEFFICIENT OF EXPANSION Doc. No : 30101-30-17D-402 C:\webpage\piping_std\30101-30-17D-402.doc

BAA Checked SHT.

2 OF 4

Approved REV. 0

Temperatuur1)

mm/m O

O

inch/100 feet

"A" + "B" 5,22 5,32 5,4 5,49 5,58

"C" 4,76 4,84 4,92 5 5,08

"D" 6,9 7,01 7,11 7,22 7,33

F 760 770 780 790 800

C 404,5 410 415,6 421,1 426,7

"A" + "B" 6,27 6,38 6,48 6,59 6,7

"C" 5,72 5,81 5,91 6 6,1

"D" 8,28 8,41 8,54 8,67 8,8

5,67 5,77 5,86 5,95 6,04

5,17 5,25 5,33 5,41 5,49

7,44 7,55 7,66 7,77 7,88

810 820 830 840 850

460 465,6 471,1 476,7 482,2

7,36 7,47 7,59 7,7 7,81

6,69 6,78 6,88 6,97 7,07

9,59 9,72 9,86 9,99 10,12

6,13 6,22 6,32 6,42 6,51

5,58 5,66 5,74 5,81 5,89

7,99 8,1 8,22 8,32 8,43

860 870 880 890 900

460 465,6 471,1 476,7 482,2

7,36 7,47 7,59 7,7 7,81

6,69 6,78 6,88 6,97 7,07

9,59 9,72 9,86 9,99 10,12

6,6 6,69 6,78 6,86 6,96

5,98 6,06 6,13 6,22 6,3

8,54 8,65 8,78 8,88 9

910 920 930 940 950

487,8 493,4 498,9 504,5 510

7,92 8,03 8,13 8,24 8,35

7,17 7,27 7,36 7,46 7,56

10,26 10,39 10,53 10,66 10,8

7,05 7,14 7,22 7,32 7,4

6,38 6,88 6,96 7,04 7,12

9,12 9,22 9,34 9,45 9,56

960 970 980 990 1000

515,6 521,1 526,7 532,2 537,8

8,46 8,57 8,67 8,78 8,89

7,66 7,76 7,86 7,96 8,06

10,94 11,07 11,21 11,34 11,48

7,5 7,6 7,69 7,79 7,88

6,8 6,88 6,96 7,04 7,12

9,68 9,79 9,9 10,02 10,13

1010 1020 1030 1040 1050

543,4 548,9 554,5 560 565,6

9 9,12 9,23 9,35 9,46

8,16 8,26 8,35 8,45 8,55

11,62 11,75 11,89 12,02 12,16

7,98 8,07 8,17 8,27 8,37

7,21 7,29 7,37 7,46 7,54

10,25 10,37 10,48 10,59 10,7

1060 1070 1080 1090 1100

571,1 576,7 582,2 587,8 593,4

9,58 9,69 9,81 9,92 10,04

8,65 8,75 8,85 8,95 9,05

12,3 12,43 12,57 12,7 12,84

Materiaal "A" A- 53 A-120 A-210 A- 83 A-161 API 5L A-106 A-192 Koolstofstaal

Materiaal "B" A-335 P-1 P-12 P- 2 P-21 P-11 P-22 3 Cr,Mo en lager

Materiaal "C" A-335 P-5 P5b P-5c P-7 P-9 hoger dan 3 Cr Mo

Materiaal "D" A-240 A312 A-249 A-269 Cr Ni staal

Note : 1. Installation temperature based on 20 0C

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK COEFFICIENT OF EXPANSION Doc. No : 30101-30-17D-402 C:\webpage\piping_std\30101-30-17D-402.doc

BAA Checked SHT.

3 OF 4

Approved REV. 0

Temperatuur1)

mm/m O

O

inch/100 feet

"A" + "B" 8,46 8,54 8,63 8,71 8,8

"C" 7,62 7,7 7,78 7,86 7,93

"D" 10,81 10,92 11,04 11,15 11,28

F 1110 1120 1130 1140 1150

C 598,9 604,5 610 615,6 621,1

"A" + "B" 10,15 10,25 10,36 10,46 10,57

"C" 9,14 9,24 9,33 9,43 9,52

"D" 12,98 13,11 13,25 13,38 13,52

8,9 8,98 9,07 9,16 9,25

8,02 8,1 8,18 8,26 8,34

11,38 11,49 11,61 11,71 11,82

1160 1170 1180 1190 1200

626,7 632,2 637,8 643,4 648,9

10,68 10,78 10,89 10,99 11,1

9,62 9,71 9,81 9,9 10

13,66 13,79 13,93 14,06 14,2

9,34 9,43 9,53 9,62 9,71

8,42 8,5 8,59 8,68 8,78

11,94 12,05 12,18 12,29 12,4

1210 1220 1230 1240 1250

654,5 660 665,6 671,1 676,7

11,21 11,32 11,44 11,51 11,66

10,11 10,21 10,32 10,42 10,53

14,34 14,47 14,61 14,74 14,88

9,8 9,89 9,99 10,09 10,19

8,86 8,95 9,04 9,13 9,22

12,52 12,62 12,73 12,86 12,97

1260 1270 1280 1290 1300

682,2 687,8 693,4 698,9 704,5

11,77 11,88 12 12,11 12,22

10,64 10,74 10,85 10,95 11,06

15,02 15,15 15,29 15,42 15,56

10,28 1,38 10,47 10,56 10,64

9,3 9,38 9,46 9,54 9,62

13,09 13,2 13,3 13,41 13,52

1310 1320 13030 1340 1350

710 715,6 721,1 726,7 732,2

12,33 12,44 12,56 12,67 12,78

11,16 11,26 11,35 11,45 11,55

15,7 15,83 15,97 16,1 16,24

10,73 10,82 10,92 11,02 11,11

9,71 9,79 9,87 9,95 10,04

13,64 13,77 13,88 13,99 14,1

1360 1370 1380 1390 1400

737,8 743,4 748,9 754,5 760

12,89 13

11,65 11,75 11,85 11,95 12,05

16,38 16,51 16,65 16,78 16,92

Materiaal "A" A- 53 A-120 A-210 A- 83 A-161 API 5L A-106 A-192 Koolstofstaal

Materiaal "B" A-335 P-1 P-12 P- 2 P-21 P-11 P-22 3 Cr,Mo en lager

13,25 13,34

Materiaal "D" A-240 A312 A-249 A-269 Cr Ni staal

Materiaal "C" A-335 P-5 P5b P-5c P-7 P-9 hoger dan 3 Cr Mo

Note : 1. Installation temperature based on 20 0C

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK COEFFICIENT OF EXPANSION Doc. No : 30101-30-17D-402 C:\webpage\piping_std\30101-30-17D-402.doc

BAA Checked SHT.

4 OF 4

Approved REV. 0

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK STRESS MONOGRAM AND FORMULAS Doc. No : 30101-30-17D-403 C:\webpage\piping_std\30101-30-17D-403.doc

BAA Checked SHT.

1 OF 3

Approved REV. 0

The monogram is based on the following simplified formulas: Shapes

“A x D” formulas min h

L

h = 0.00735 DLT

h

C B

h

L L

h

h L1 L2

max L

h

2

18510h L= DT L=B=C hFL B ≥4 C 2 h = 0.00588 DLT 28923h L= DT hFL 2 h = 0.00661 D( L1 − L2 )T 22887 h ( L1 − L2 ) = DT h F (L1 − L2 )

h = 0.00294 DLT

W

2

L=

h

h L

N B 0 .5 h

hFL

115700h DT w = 1.5h Pref.

h ≥ AxD B ≥ AxD

h≥

AxD 1.25

(h = L2 ) ≥ AxD

h≥

AxD 1.25

Legend A = Correction factor at temperature difference “T”. D = Outside diameter of pipe in mm. h = Length of shortest leg in m. L = Length of leg at 900 to “h” in m. T = Temperature difference in 0C. (max. operating temperature minus installation temperature) installation temperature : usually 200C. Notes: 1. The formulas are based on standard weight, carbon steel and low alloy piping. DO NOT USE the formulas for stainless steel and aluminium. 2. If the wall thickness of the specified pipe differs from the standard weight, a correction factor must be applied : new min h (adjusted) = lp of pipe specified x min h (from formula) lp of std wt. pipe new max L (adjusted) =

lp of std wt. pipe x m x max L (from formula) lp of pipe specified

where : lp = moment of inertia in cm 4. 0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK STRESS MONOGRAM AND FORMULAS Doc. No : 30101-30-17D-403 C:\webpage\piping_std\30101-30-17D-403.doc

BAA Checked SHT.

2 OF 3

Approved REV. 0

3. If a pipeline is connected to “sensitive” equipment, such as pumps, turbines, heaters, etc . the ‘min h” and “h” from monogram or formula should be multiplied by 1.5’ 1 the “max L” should be multiplied by 2.25

Examples: (using the monogram) GIVEN : nom pipe size = 6”. T = 320 – 20 = 300 0C. L = 8m L shape Required; “h” for minimum flexibility. Solution: “A x D” formula 1. Enter temp difference. on scale “p” Connect “p” with nom dia. on scale nom.pipe size. Read “h” on scale “h” for given shape (h = 3.4 m) Required: “min h” for sufficient flexibility. Solution: “DTL” formula. 2. Enter temp difference. on scale “T” Connect “T” with nom dia. on scale nom.pipe size. Intersection line “q”. 3. Connect point of intersection with length on scale “L”, intersecting line “r”. 4. Move horizontally from point of intersection to the scale representing the shape and read “min h”. (min h = 3.7 m) Conclusion ; leg “h” must be ≥ 3.7 m GIVEN: nom pipe size = 2”. T = 120 – 20 = 100 0C. h = 1m U shape Required; “max “. Solution: “DTL” formula 1. Enter “h” on scale “h” representing the shape, move horizontally intersecting line “r” 2. Enter temp. difference on scale “T”. Connect “T” with nom. dia. on scale nom. pipe size, intersecting line “q” 3. Connect intersection of points of “r” and “q”. Lengthen this line to “L” and read “max L”. Conclusion : max. leg L = 4.8 m

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK STRESS MONOGRAM AND FORMULAS Doc. No : 30101-30-17D-403 C:\webpage\piping_std\30101-30-17D-403.doc

BAA Checked SHT.

3 OF 3

Approved REV. 0

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HANDBOOK STOOMWEZEN APPROVAL CRITERIA Doc. No : 30101-30-17D-404 C:\webpage\piping_std\30101-30-17D-404.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

ND 2" 3" 4" 6" 8" 10" 12" 14" 16' 18" 20' 24" 26" 28" 30" 32" 34" 36' 42"

sch 40 40 40 40 30 30 30 30 30 20 20 20

Pipe BW w.t. 3,91 5,49 6,02 7,11 7,04 7,8 8,38 7,92 9,53 7,92 9,53 9,53

150# 2,3 4 5,9 8,6 13,6 19,5 29 40,8 48 59 74,8 100 113 129 145 180 191 218 308

300# 3,2 6,9 10,7 17,7 26,3 37,2 52,2 74,8 100 127 147 223 259 260 367 408 448 544 730

ND 2" 3" 4" 6" 8" 10" 12" 14" 16' 18" 20' 24" 26" 28" 30" 32" 34" 36' 42"

Fitting BW kg/m 1 elb 90 lr cap eq tee 5,44 0,69 0,23 0,8 11,28 2,12 0,65 1,8 16,06 4 1,15 2,8 28,23 10,6 2,9 6,4 36,75 18,3 4,4 10,6 50,95 31,6 7,6 17,5 65,13 49 11,8 26,5 81,95 71,7 16,1 29,7 93,12 94 20,3 33,8 87,84 99 21,7 43,7 116,96 147 32,2 53,1 140,79 211 46,3 99

Flanges Slip-on / kg 600# 900# 1500# 4 11,4 11,4 7,3 11,3 21,3 16,8 23,2 34,1 37,6 47,7 77,2 52,2 86,3 129 80,3 125 220 97,5 168 286 120 188 404 166 211 522 216 295 670 278 368 806 397 704 1283 431 685 435 820 533 952 635 1150 680 1360 743 1542 1056

2500# 16,8 36,3 54,5 143 213 409 499

150# 2,7 4,5 6,8 10,9 17,7 23,6 36,3 50 63,6 68,1 81,7 118 136 143 170 197 213 240 340

Welding Neck / kg 300# 600# 900# 4,5 5,4 11,4 6,8 10,4 14,1 11,4 19 23,2 19,1 36,7 50 30,4 54,4 79,5 41,3 86,1 118 63,3 103 148 81,7 127 182 114 177 225 145 216 309 182 268 317 263 377 681 304 465 722 370 470 849 422 590 985 470 680 1180 544 748 1387 580 794 1582 788 1095

150# 2,7 4,5 6,8 10,9 17,7 23,6 36,3 49,9 63,5 68 81,6 117,9 305 359 417 533 595 728 1038

300# 4,1 6,8 11,3 19,1 30,4 41,3 63,5 81,6 113,4 145,2 181,4 263,1 456 560 653 756 886 1032 1167

1500# 11,4 21,8 33,1 75 125 207 313 427 568 738 931 1510

Flanges Blind / kg 600# 900# 1500# 5,4 11,3 11,4 10,4 14,1 21,08 19,3 23,1 33,1 36,7 49,9 74,8 54,4 79,4 124,7 86,2 117,9 206,4 102,1 147,4 313 127 181,4 426,4 176,9 224,5 567 215,5 308,4 737,1 267,6 376,5 929,9 375,5 680,4 1508,2 732 1048 868 1302 1024 1555 1202 1878 1366 2230 1590 2571 1935 3168

2500# 19,1 42,7 65,8 173 263 488 692

2500# 19,1 42,6 65,6 172,4 263,1 487,6 691,7

Note: Weights of flanges are based on the heaviest of Tube turn, Taylor forge, Ladish vogt Weights of valves are based on the heaviest of Crane, Pacific, Oic, Chapman and TK Valves. For final of weights – check make of purchased material and refer to catalog.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HAND BOOK

BAA Checked Approved SHT.

1 OF 2 WEIGHT OF VALVES,FLANGES AND FITTINGS Doc. No : 30101-30-17D-405 C:\webpage\piping_std\30101-30-17D-405.doc

REV. 0

ND 2" 3" 4" 6" 8" 10" 12" 14" 16' 18" 20' 24" 26" 28" 30" 32" 34" 36' 42"

150# 26 50 72 134 227 286 376 522 717 866 1066 1769

300# 34 66 100 200 320 476 676 984 1270 1687 2104 3348

2540

5466

1500#

2500#

150# 21 36 64 113 191 271 374

1500# 55 110 250 550 770 1430 1980 2390 3460 4930 7230 12320

2500# 95 250 360 860 2270 3050 4320

150# 15 29 44 91 177 231 352 544 658 689 835 1175

300# 36 60 97 180 285 311

Globe Valve 600# 900# 46 100 168 346 555

1500#

2500#

1500# 72 126 284 612 945

2500#

3520 5890

ND 2" 3" 4" 6" 8" 10" 12" 14" 16' 18" 20' 24" 26" 28" 30" 32" 34" 36' 42"

Gate Valve 600# 900# 48 104 177 360 553 853 1193 1453 1919 3266 4445 5352

150# 20 30 55 230 340 550 770 1070 1390 2000 2410 3960 4770 5500 6800

Ball Vavle FB 300# 600# 900# 25 30 55 45 55 80 75 100 150 250 270 320 390 550 700 570 770 840 870 1000 1320 1180 1340 1750 1570 2070 2160 2270 2890 3200 2500 3020 4570 4200 5250 6090 5320 6230 6400 10200 7700 10900

11400

11800

Check, swing type 300# 600# 900# 28 38 72 54 80 81 82 130 153 150 307 288 281 408 531 417 658 585 894 748 930 1098 1423 2010

17100

Note: Weights of flanges are based on the heaviest of Tube turn, Taylor forge, Ladish.vogt Weights of valves are based on the heaviest of Crane, Pacific, Oic, Chapman and TK Valves. For final of weights – check make of purchased material and refer to catalog.

0 Rev.

01/2002 Date

First Issue

LEA Prepared

Description PIPING HAND BOOK

BAA Checked Approved SHT.

2 OF 2 WEIGHT OF VALVES,FLANGES AND FITTINGS Doc. No : 30101-30-17D-405 C:\webpage\piping_std\30101-30-17D-405.doc

REV. 0

Typical arrangement between vessel and pipe rack and typical arrangement of nozzles Vent Inlet Vapour Out Pipe Rack

Manhole Steam Out Liquid Outlet S.S.

Safety Relief Open System Inlet Vent

T.L.

F.S.

Safety Relief Closed system

Vapour Out

Gas Blanket

Press. indicator

T.L.

Water Draw Off

LC LC

0 Rev.

01/2002 Date

Liquid Pump Out

Draw off Drain

Steam Out

Temp. Indicator.

Manhole

Sliding Support

Fixed support

First Issue Description

LEA Prepared

PIPING HAND BOOK TYP. ARRANGEMENT FOR HOR. VESSEL Doc. No : 30101-30-17D-500 C:\webpage\piping_std\30101-30-17D-500.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

Shell Head 610 1220 2135 2745

Bend Size C

B

table of saddle spacing O.D. Tank A B to 1070 incl. 535 300 to 1985 incl. 610 345 to 2590 incl. 685 355 to 3660 incl. 765 380

C 190 215 270 320

D 3" 4" 6" 8"

A

B

Centerline Vessel

C

A

Vessel Dia. 610 765 915 1070 1220 1375 1525 1675 1830 1980

0 Rev.

01/2002 Date

A 558 685 815 965 1095 1220 1345 1475 1600 1755

B 485 560 635 710 785 865 940 1015 1095 1170

G 150 150 150 150 200 200 200 200 200 200

Vessel Dia. 2135 2285 2440 2590 2743 2895 3050 3200 3355 3505 3660

A 1880 2005 2135 2285 2415 2540 2665 2795 2945 3075 3200

First Issue Description

B 1245 1320 1395 1475 1550 1625 1700 1780 1855 1930 2005

LEA Prepared

PIPING HANDBOOK SADDLES FOR HORIZONTAL VESSELS Doc. No : 30101-30-17D-501 C:\webpage\piping_std\30101-30-17D-501.doc

G 230 230 230 230 255 255 255 255 255 255 255

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HANDBOOK STANDARD FOR VERTICAL VESSELS Doc. No : 30101-30-17D-502 C:\webpage\piping_std\30101-30-17D-502.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

SUPPORT AND GUIDE DISTANCES

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HANDBOOK STANDARD FOR VERTICAL VESSELS Doc. No : 30101-30-17D-502 C:\webpage\piping_std\30101-30-17D-502.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK LEG SUPPORT FOR VERTICAL VESSELS Doc. No : 30101-30-17D-503 C:\webpage\piping_std\30101-30-17D-503.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK LUG SUPPORT FOR VERT. VESSELS Doc. No : 30101-30-17D-504 C:\webpage\piping_std\30101-30-17D-504.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK HEAT EXCHANGER NOMENCLATURE Doc. No : 30101-30-17D-505 C:\webpage\piping_std\30101-30-17D-505.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HANDBOOK HEAT EXCHANGER NOZZLE POSITION Doc. No : 30101-30-17D-506 C:\webpage\piping_std\30101-30-17D-506.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

FRONTEN KLŐPPER VORM Afmetingen en gewichten Inhoud tot tangent lijn Buiten oppervlak tot tangent lijn Binnen oppervlak tot tangent lijn

: I = - 0,1 (D-2t)* (D-2t)* (D-2t) : Ou = 0,99 D*D : Oi = 0,99 (D-2t)* (D-2t) R = D r = D/10 h1 = ~D/5 = ho - a

Tussenliggende diameters zijn ook te leveren

a Wanddikte

t

Lengte manchet

h

0 6

7

8

9

10

4 11

12

13

14

15

16

17

18

19

70

60

20

21

22

23

80

D

R

r

ho

mm

mm

mm

mm

300

300

30

52

8

10

11

12

14

16

18

19

20

22

24

26

27

29

30

32

34

38

400

400

40

71

12

14

16

18

20

24

26

28

30

32

36

38

40

42

45

47

49

56

500

500

50

91

17

20

23

26

29

33

36

39

42

45

50

53

56

59

62

65

68

77

600

600

60

110

23

27

31

35

39

44

48

52

56

60

67

71

75

79

83

87

91

102

700

700

70

129

30

35

40

45

50

57

62

67

72

77

85

90

96

101

106

112

117

130

800

800

80

149

38

45

51

58

64

73

79

86

92

99

109

116

122

129

136

143

150

165

900

900

GEWICHT IN KG

90

168

55

63

71

79

89

97

105

113

122

133

141

150

158

166

175 1183 201

1000 1000 100

187

67

76

86

95

107

117

127

137

146

160

170

180

190

200

210

220

241

1100 1100 110

206

79

90

102

113

127

139

150

162

173

189

201

213

225

236

248

260

284

1200 1200 120

226

94

107

121

134

151

164

178

192

206

224

238

252

266

280

294

308

335

1300 1300 130

246

110

126

141

157

177

192

208

224

240

261

278

294

310

327

343

359

390

1400 1400 140

265

144

162

180

201

220

238

256

274

298

317

336

354

373

392

410

445

1500 1500 150

284

163

183

204

228

249

270

290

311

338

359

380

401

422

443

464

502

1600 1600 160

304

184

207

230

258

281

305

328

352

381

405

429

453

477

300

524

566

1700 1700 170

323

233

259

289

316

342

368

395

428

454

481

508

535

561

588

634

1800 1800 180

342

258

286

320

349

378

407

436

473

502

532

561

591

620

650

700

1900 1900 190

362

286

318

355

387

420

452

484

524

557

590

622

655

688

721

775

2000 2000 200

381

315

350

390

426

461

497

532

576

612

648

684

720

756

792

850

2100 2100 210

400

325

429

468

507

546

585

632

672

711

751

791

830

870

933

2200 2200 220

420

422

510

512

555

598

640

692

735

778

822

865

908

951 1020

2300 2300 230

439

458

552

556

603

649

696

751

798

845

892

939

986 1033 1106

2400 2400 240

458

496

600

603

653

703

753

813

864

914

965 1016 1067 1118 1196

2500 2500 250

478

539

646

655

709

764

818

883

938

993 1048 1104 1159 1214 1298

2600 2600 260

497

693

705

763

822

881

950 1009 1069 1128 1187 1246 1306 1395

2700 2700 270

517

747

756

819

882

945 1019 1083 1146 1210 1274 1337 1401 1495

2800 2800 280

536

815

883

950 1018 1097 1166 1234 1303 1372 1440 1509 1609

2900 2900 290

555

870

943 1015 1088 1172 1245 1318 1391 1464 1538 1611 1717

3000 3000 300

574

927 1005 1082 1159 1248 1326 1404 1482 1560 1639 1717 1829

3200 3200 320

613

1059 1147 1235 1323 1424 1513 1602 1691 1720 1869 1952 2048

3400 3400 340

631

1491 1604 1704 1804 1904 2005 2105 2205 2344

3600 3600 360

690

1675 1802 1914 2027 2139 2252 2365 2478 2631

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

507

PIPING HAND BOOK KLŐPPER VORM Doc. No : 30101-30-17D-507 C:\webpage\piping_std\30101-30-17D-507.doc

FRONTEN KORBBOGEN VORM Afmetingen en gewichten Inhoud tot tangent lijn : I = - 0,1298 (D-2t)* (D-2t)* (D-2t) Buiten oppervlak tot tangent lijn : Ou = 1,08 D*D Binnen oppervlak tot tangent lijn : Oi = 1,08 (D-2t)* (D-2t)* R = 0,8D r = D/6,5 h1 = ~D/4 = ho – a

Tussenliggende diameters zijn ook te leveren

0

a Wanddikte

t

Lengte manchet

h

D

R

r

ho

mm

mm

mm

mm

6

7

8

9

10

4 11

12

60

13

14

15

16

17

18

8

19

20

21

22

80

70

23 100

GEWICHT IN KG

300

240

45

70

9

10

12

13

15

17

18

20

21

23

25

27

28

30

32

33

35

39

400

320

60

95

13

15

17

20

22

25

27

30

32

34

38

41

43

45

48

50

52

59

500

400

80

121

18

22

25

22

31

35

38

42

45

48

53

56

60

63

66

70

73

82

600

480

95

147

25

29

33

37

41

47

51

55

60

64

71

75

79

84

88

93

97

108

700

560

110

172

38

43

49

54

62

67

73

78

84

92

98

103

110

115

121

127

141

800

640

125

197

48

55

62

69

78

85

93

100

107

117

124

132

139

146

154

161

177

900

720

140

223

59

68

76

85

95

104

113

121

130

142

151

160

169

177

187

196

215

1000

800

155

248

72

82

93

103

116

126

137

148

158

173

183

194

205

216

226

237

259

1100

880

170

274

99

111

123

139

151

163

176

189

206

218

231

244

257

270

283

308

1200

960

185

299

116

131

145

163

178

193

207

222

242

258

272

287

302

317

332

361

1300 1040

200

325

135

152

169

189

207

224

241

258

281

298

316

333

351

369

386

418

1400 1120

215

350

156

175

195

218

238

258

277

297

322

343

363

383

403

423

444

479

1500 1200

230

376

202

224

251

274

297

319

342

371

394

417

440

464

487

510

550

1600 1280

245

401

228

254

283

309

335

361

387

419

445

471

497

523

550

576

620

1700 1360

260

427

257

285

318

347

376

405

434

470

498

528

558

587

617

646

694

1800 1440

280

452

286

318

355

387

419

451

484

523

556

589

621

654

687

720

773

1900 1520

290

478

353

393

429

465

501

536

580

616

652

688

725

761

797

855

2000 1600

310

503

386

431

470

509

548

587

634

674

713

753

793

832

872

934

2100 1680

325

529

473

516

559

602

645

696

740

783

827

870

914

957

1025

2200 1760

340

554

517

564

612

659

706

761

809

857

904

952

999

1047 1120

2300 1840

355

580

615

666

718

769

829

881

933

985

1036 1088 1140 1218

2400 1920

370

608

668

723

779

835

900

956

1012 1069 1124 1181 1237 1321

2500 2000

385

631

783

843

903

974

1034 1095 1156 1217 1278 1339 1428

2600 2080

400

656

845

910

975

1050 1126 1181 1247 1313 1378 1444 1539

2700 2160

415

682

980

1049 1130 1200 1271 1341 1412 1483 1553 1655

2800 2240

430

707

1051 1126 1212 1288 1363 1439 1515 1591 1667 1774

2900 2320

445

733

1205 1297 1378 1459 1540 1622 1703 1784 1898

3000 2400

460

758

1295 1393 1480 1567 1654 1741 1828 1915 2036

3200 2560

490

808

1578 1677 1776 1874 1973 2071 2170 2305

3400 2720

525

859

1997 2108 2219 2330 2441 2591

3600 2880

555

910

2492 2616 2740 2907

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

507

PIPING HAND BOOK KORBBOGEN VORM Doc. No : 30101-30-17D-508 C:\webpage\piping_std\30101-30-17D-508.doc

IPE-STEEL Acc. to Euronorm 19-57 and DIN 1025

0 Rev.

01/2002 Date

LEA Prepared

Description PIPING HAND BOOK

IPE -STEEL Doc. No : 30101-30-17D-600 C:\webpage\piping_std\30101-30-17D-600.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

HE-A STEEL Acc. to Euronorm 53-62 and DIN 1025

0 Rev.

01/2002 Date

LEA Prepared

Description PIPING HAND BOOK

HE-A STEEL Doc. No : 30101-30-17D-601 C:\webpage\piping_std\30101-30-17D-601.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

HE-B STEEL Acc. to Euronorm 53-62 and DIN 1025

0 Rev.

01/2002 Date

LEA Prepared

Description PIPING HAND BOOK

HE-B STEEL Doc. No : 30101-30-17D-602 C:\webpage\piping_std\30101-30-17D-602.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

UNP-STEEL Acc. to DIN 1026

0 Rev.

01/2002 Date

LEA Prepared

Description PIPING HAND BOOK

UNP- STEEL Doc. No : 30101-30-17D-603 C:\webpage\piping_std\30101-30-17D-603.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

EQUAL L-STEEL Acc. to Euronorm 56-65 and DIN 1028

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK EQUAL L-STEEL STEEL Doc. No : 30101-30-17D-604 C:\webpage\piping_std\30101-30-17D-604.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

UNEQUAL L-STEEL Acc. to Euronorm 57-65 and DIN 1029

0 Rev.

01/2002 Date

Description

LEA Prepared

PIPING HAND BOOK UNEQUAL L- STEEL Doc. No : 30101-30-17D-605 C:\webpage\piping_std\30101-30-17D-605 .doc

BAA Checked

Approved

SHT. 1 OF 1

REV. 0

NOTES : 1 Width of stairs 750 mm 2 Max. rise is 200 mm 3 Any flight of stairs shall not have more than 20 rises.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK GENERAL ARRANGEMENT STAIRWAYS Doc. No : 30101-30-17D-606 C:\webpage\piping_std\30101-30-17D-606.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

Notes : 1 Minimum dimension between adjacent stairs (back to back of stair stringers ) depends of type of handrail and size of stringer used ( 250 mm or 450 mm). 2 Handrails shall have a minimum finger clearance of 75mm to walls ,columns and each other. 3 Minimum stair landing width shall be 750mm.

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK GENERAL ARRANGEMENT STAIRWAYS Doc. No : 30101-30-17D-606 C:\webpage\piping_std\30101-30-17D-606.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

0 Rev.

01/2002 Date

LEA Prepared

Description PIPING HAND BOOK

CAGE LADDER Doc. No : 30101-30-17D-607 C:\webpage\piping_std\30101-30-17D-607.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK CAGE LADDER AT COLUMN Doc. No : 30101-30-17D-608 C:\webpage\piping_std\30101-30-17D-608.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

NOTES: If height of platform > 1500 mm handrail on one side only If height of platform < 1500 mm handrail to be on both sides

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK TYP. DETAIL OF HAND RAIL Doc. No : 30101-30-17D-609 C:\webpage\piping_std\30101-30-17D-609.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0

MINIMUM STRAIGHT LENGTH REQUIREMENTS FOR FLOW ELEMENTS

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK STRAIGHT LENGTH REQUIRMENTS FOR FLOW ELEMENTS Doc. No : 30101-30-17D-700 C:\webpage\piping_std\30101-30-17D-700.doc

BAA Checked SHT.

1 OF 2

Approved REV. 0

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK STRAIGHT LENGTH REQUIRMENTS FOR FLOW ELEMENTS Doc. No : 30101-30-17D-700 C:\webpage\piping_std\30101-30-17D-700.doc

BAA Checked SHT.

2 OF 2

Approved REV. 0

ORIENTATION FOR ORIFICE FLANGES

0 Rev.

01/2002 Date

First Issue Description

LEA Prepared

PIPING HAND BOOK ORIENTATION FOR ORIFICE FLANGES Doc. No : 30101-30-17D-701 C:\webpage\piping_std\30101-30-17D-701.doc

BAA Checked SHT.

1 OF 1

Approved REV. 0