Raptor Cone Crusher

Raptor® 900 cone crushers

2

Raptor® 900 clearance dimensions

(in)

(mm)

A

Adjustment Ring Max Diameter

138.69

3523

B

Inside Diameter of Feed Hopper

70.57

1792

C

Clearing Stroke Travel

5.89

150

D

Height from Base to Top of Feed Hopper

138.00

3502

E

Base to Bottom of Oil Piping

28.21

717

F

Base to Bottom of Main Frame Hub

14.37

365

88.71

2253 2649

G

Base to Top of Feed Plate Base to Top of Feed Plate (Anti-Spin)

H

Hub Diameter of Main Frame

104.31

I

Crusher Centerline to Main Frame Flange

27.95

710

J

Clearance Required to Remove Countershaft Assembly

64.37

1635

K

Crusher Centerline to End of Countershaft

137.00

3480

L

Crusher Centerline to Countershaft Housing Face

88.13

2239

Clearance Required to Remove Head Assembly

63.98

1625

M1

Standard

176.00

4470

M2

Short Head

191.00

4851

170.00

4318

N

Clearance Required to Remove Bowl Assembly Standard & Short Head

All dimensions are for reference only and are not to be used for construction.

Capacity chart Setting

mt/hr/

mt/hr

Settings

stph

stph

mm

Min

Max

Inches

Min

Max

Short Head Fine

10

275

350

3/8

300

385

Short Head Fine

12

300

425

1/2

330

470

Short Head Medium

14

330

455

9/16

360

500

Short Head Medium

16

400

550

5/8

440

600

Short Head Coarse

19

440

600

3/4

485

660

Standard Fine

22

500

675

7/8

550

745

Standard Fine

25

525

770

1

575

850

Standard Fine

32

600

900

1-1/4

660

990

Standard Medium

38

650

1050

1-1/2

715

1150

45

780

1250

1-3/4

860

1370

Reduction Ratio

4 to 6

2 to 4

Reduction Ratio

4 to 6

2 to 4

Standard Coarse

As indicated above for 100 lbs. per cubic foot and impact work index of 13. Short tons per hour based on open circuit crushing with material weighing 100 pounds per cubic foot. Values are estimated “instantaneous” product samples, actual values may vary ±15%. Factors that will vary throughput are; feed gradation, cavity level, feed distribution, moisture content, and properties of the processed material.

3

General arrangement

All dimensions are for reference only and are not to be used for construction

Product gradation table Percent passing for a given closed side setting Average feed material (12 to 14wi) Product Size

3/8”

1/2”

5/8”

3/4”

7/8”

1”

1 1/4”

1 1/2”

2”

(10 mm)

(13 mm)

(16 mm)

(19 mm)

(22 mm)

(25 mm)

(31 mm)

(38 mm)

(50 mm)

100

94-98

4” (100 mm)

100

3” (75 mm) 2” (50 mm) 1-1/2” (38 mm)

100

1” (25 mm)

95-99

96-99

89-95

65-71

87-93

73-79

47-53

95-99

92-97

85-88

71-77

46-52

37-43

25-31

3/4” (19 mm)

100

93-98

86-92

79-85

65-71

54-60

34-40

27-33

19-25

1/2” (13 mm)

89-95

75-81

63-69

52-58

40-46

33-39

19-25

15-21

11-17

3/8” (10 mm)

78-84

63-69

52-58

42-48

31-37

37-33

15-21

12-18

9-14

1/4” (6 mm)

52-58

40-46

33-39

26-32

19-25

16-21

9-15

6-12

4-11

Values listed will vary depending on feed distribution, cavity level, feed gradation, crushing chamber, moisture and material density.

Feed Openings Minimum closed side

CSS “A”

1.18” (30 mm)

14.75” (370 mm)

Standard Medium

.98” (25 mm)

12.09” (307 mm)

Standard Fine

.63” (16 mm)

9.92” (252 mm)

Short Head Coarse

.55” (14 mm)

6.78” (172 mm)

Short Head Medium

.47” (12 mm)

5.96” 9151 mm)

Short Head Fine

.39” (10 mm)

3.45” (88 mm)

3

1

Standard Coarse

Lifting Weights Complete Crusher Main Frame Assembly (includes main shaft and frame liner)

(lbs.)

(kg)

158,356

71,830

46,998

21,318

2 5

4

Bowl Assembly

36,886

16,731

20,210

9,167

24,929

11,308

Countershaft Box Assembly

3,795

1,721

Eccentric Assembly (includes counterweight)

12,400

5,625

Mantle

9,780

4,436

Bowl Liner

9,985

4,529

Dry

2,150

975

Wet

3,045

1,381

Dry

5,500

2,495

Wet

8,250

3,742

(includes bowl liner and hopper assembly) Adjustment Ring (includes clamping ring) Head Assembly (feed plate assembly and mantle)

Feed size “B” at min.

setting “A”

23 7

12

9

11

15

8 10

6 16

17

18

19

14

24 20

Power Unit 21

13 22

Lube-Air

1.

Hopper Assembly

9.

2.

Bowl

10. Socket Liner

18. Eccentric

3.

Adjustment Cap

11. Adjustment Ring

19. Counterweight

Bowl Liner

17. Main Shaft

Dry

5,800

2,631

4.

Drive Ring

12. Clamping Cylinder

20. Gear

Wet

8,550

3,878

5.

Feed Plate Assembly

13. Main Frame

21. Countershaft

2,300

1,043

6.

Head Assembly

14. Main Frame Liner

22. Pinion

7.

Torch Ring

15. Main Frame Seat Liner

23. Wedge

8.

Mantle

16. Tramp Release Cylinder 24. Arm Guard

Air Cooler

NOTE: Allowable casting weights vary ±5%

Copyright © 2013 FLSmidth A/S. ALL RIGHTS RESERVED. FLSmidth is a (registered) trademark of FLSmidth A/S. This brochure makes no offers, representations or warranties (express or implied), and information and data contained in this brochure are for general reference only and may change at any time.

Minerals Processing Tech;nology Center FLSmidth Salt Lake City, Inc. 7158 S. FLSmidth Dr. Midvale, UT 84047-5559 USA Tel: +1 801 871 7000 Fax: +1 801 871 7001 Email: [email protected]

www.flsmidth.com

Rev. 11/11/2013 al-us

Lube-Water