Aws B5. 2. 2018 .pdf

AWS B5.2:201 8 An American National Standard

Specifcation for the Training, Qualifcation, and Company Certifcation of Welding Inspector Specialists and Welding Inspector Assistants

AWS B5.2:201 8 An American National Standard Approved by the American National Standards Institute May 1 1 , 201 7

Specifcation for the Training, Qualifcation, and Company Certifcation of Welding Inspector Specialists and Welding Inspector Assistants 2nd Edition

Supersedes AWS B5.2:2001 Prepared by the AWS Personnel & Facility Qualifcation Committee Under the Direction of the AWS Standards Council Approved by the AWS Board of Directors

Abstract This specifcation defnes the requirements and program for an employer (company) to train, qualify, and company certify Welding Inspector Specialists and Welding Inspector Assistants to contract or industry-specifc inspector standards. The program is developed as a written practice and controlled by an employer. The qualifcation requires documentation of experience, training, and satis factory completion of an examination. The examination tests knowledge of welding processes, welding procedures, welder qualifcation, destructive testing, nondestructive testing, terms, defnitions, symbols, reports, records, safety, and responsibility as specifcally applied by the contract or industry standards applicable to the employer.

AWS B5.2:201 8

ISBN: 978-0-87171-925-6 ©2018 by American Welding Society All rights reserved Printed in the United States of America Photocopy Rights. No portion o f this standard may be reproduced, stored in a retrieval system, or transmitted in any form, including mechanical, photocopying, recording, or otherwise, without the prior written permission of the copyright owner. Authorization to photocopy items for internal, personal, or educational classroom use only or the internal, personal, or educational classroom use only o f specifc clients is granted by the American Welding Society provided that the appropriate fee is paid to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, tel: (978) 750-8400; Internet: www.copyright.com.

ii

AWS B5.2:201 8

Statement on the Use of American Welding Society Standards All standards (codes, specifcations, recommended practices, methods, classifcations, and guides) of the American Welding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of the American National Standards Institute (ANSI). When AWS American National Standards are either incorporated in, or made part of, documents that are included in federal or state laws and regulations, or the regulations of other governmental bodies, their provisions carry the full legal authority of the statute. In such cases, any changes in those AWS standards must be approved by the governmental body having statutory jurisdiction before they can become a part of those laws and regulations. In all cases, these standards carry the full legal authority of the contract or other document that invokes the AWS standards. Where this contractual relationship exists, changes in or deviations from requirements of an AWS standard must be by agreement between the contracting parties. AWS American National Standards are developed through a consensus standards development process that brings together volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers the process and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or verify the accuracy of any information or the soundness of any judgments contained in its standards. AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or reliance on this standard. AWS also makes no guarantee or warranty as to the accuracy or completeness of any information published herein. In issuing and making this standard available, AWS is neither undertaking to render professional or other services for or on behalf of any person or entity, nor is AWS undertaking to perform any duty owed by any person or entity to someone else. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. It is assumed that the use of this standard and its provisions is entrusted to appropriately qualifed and competent personnel. This standard may be superseded by new editions. This standard may also be corrected through publication of amendments or errata, or supplemented by publication of addenda. Information on the latest editions of AWS standards including amendments, errata, and addenda is posted on the AWS web page (www.aws.org). Users should ensure that they have the latest edition, amendments, errata, and addenda. Publication of this standard does not authorize infringement of any patent or trade name. Users of this standard accept any and all liabilities for infringement of any patent or trade name items. AWS disclaims liability for the infringement of any patent or product trade name resulting from the use of this standard. AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so. Offcial interpretations of any of the technical requirements of this standard may only be obtained by sending a request, in writing, to the appropriate technical committee. Such requests should be addressed to the American Welding Society, Attention: Managing Director, Certifcation Department, (see Annex D). With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards may be rendered. These opinions are offered solely as a convenience to users of this standard, and they do not constitute professional advice. Such opinions represent only the personal opinions of the particular individuals giving them. These individuals do not speak on behalf of AWS, nor do these oral opinions constitute offcial or unoffcial opinions or interpretations of AWS. In addition, oral opinions are informal and should not be used as a substitute for an offcial interpretation. This standard is subject to revision at any time by the AWS Qualifcation and Certifcation Committee. It must be reviewed every fve years, and if not revised, it must be either reaffrmed or withdrawn. Comments (recommendations, additions, or deletions) and any pertinent data that may be of use in improving this standard are requested and should be addressed to AWS Headquarters. Such comments will receive careful consideration by the AWS Qualifcation and Certifcation Committee and the author of the comments will be informed of the Committee’s response to the comments. Guests are invited to attend all meetings of the AWS QCIS Subcommittee on Welding Inspector Specialists to express their comments verbally. Procedures for appeal of an adverse decision concerning all such comments are provided in the Rules of Operation of the Qualifcation and Certifcation Committee. A copy of these Rules can be obtained from the American Welding Society, 8669 NW 36 St, # 130, Miami, FL 33166. iii

AWS B5.2:201 8

This page is intentionally blank.

iv

AWS B5.2:201 8

Personnel Personnel and Facilities Qualifcation Committee P. A. Grimm, Chair R. E. Dines, Vice Chair S. P. Hedrick, Secretary I. A. Cross F. J. Fascenda K. M. Gilgenbach R. L. Holdren V. Kuruvilla D. Logan B. W. Phillips J. R. Reid D. L. Twitty

Modern Welding Company United Technical Inc. American Welding Society Valiant TMS Consultant Airgas ARC Specialties/Welding Consultants, LLC Lexicon/Genesis Quality Systems Alloy Engineering Consultant Reid Consulting Dona Ana Community College ofNew Mexico State University

AWS B5B Subcommittee on Welding Inspector Specialists

J. R. Reid S. P. Hedrick, Secretary K. W. Coryell P. A. Grimm

Reid Consulting American Welding Society Consultant Modern Welding Company

v

AWS B5.2:201 8

This page is intentionally blank.

vi

AWS B5.2:201 8

Foreword This foreword is not part of this standard but is included for informational purposes only.

This is the second edition of AWS B5.2. The frst edition was published in 2001. Revisions in this edition were made to Clauses 1 (Scope), 7 (Written Practice), 8 (Physical Requirements), 9 (Training), 10 (Examination Requirements), and 11 (Certifcation). The title of the standard has been revised to better ref ect its scope. The changes are widespread enough that clear markup of the changes is diffcult. The frst edition of AWS B5.2 superseded QC2-93, Recommended Practice for the Training, Qualifcation, and Certifcation, of Welding Inspector Specialist and Welding Inspector Assistant.

AWS B5.2 provides the framework for an in-house certifcation program and written practice for welding inspectors. To differentiate it from the central certifcation program of AWS supported by the AWS B5.1 and QC1 standards, B5.2 uses the nomenclature welding inspector ‘specialist’ . This specifcation for the qualifcation of welding inspector specialists and welding inspector assistants was developed to provide a qualifcation basis which defnes minimum requirements for a welding inspector specialist to demonstrate competence through a combination of education, experience, and examination. Comments and suggestions for the improvement of this standard are welcome. They should be sent to the Secretary, AWS Qualifcation and Certifcation Committee, American Welding Society, 8669 N.W. 36 Street, Miami, FL 33166.

vii

AWS B5.2:201 8

This page is intentionally blank.

viii

AWS B5.2:201 8

Tabl e o f Con ten ts

Pag e N o.

Personnel ....................................................................................................................................................................... v Foreword .................................................................................................................................................................... vii

1. Scope .................................................................................................................................................................... 1 2. References ............................................................................................................................................................ 2

2.1 2.2

Normative References ................................................................................................................................. 2 Informative References ............................................................................................................................... 2

3. Terms and Defnitions ......................................................................................................................................... 2 4. Levels of Qualifcation ........................................................................................................................................ 2

4.1 4.2

Welding Inspector Specialist ....................................................................................................................... 2 Welding Inspector Assistant ........................................................................................................................ 2

5. Functions ............................................................................................................................................................. 3 6. Education and Experience .................................................................................................................................. 3 7. Written Practice .................................................................................................................................................. 4 8. Physical Requirements ....................................................................................................................................... 4 9. Training................................................................................................................................................................ 4 10. Examination Requirements ................................................................................................................................ 4

10.1 Profciency Examination ............................................................................................................................. 4 10.2 Welding Inspector Specialist Examination .................................................................................................. 4 10.3 Welding Inspector Assistant Examination ................................................................................................... 5

11. Third Party Agencies .......................................................................................................................................... 5 12. Certifcation ......................................................................................................................................................... 5 13. Company Responsibilities .................................................................................................................................. 5 Annex A (Normative)—Body of Knowledge ................................................................................................................. 7 Annex B (Informative)—Sample Outline for Written Practice .................................................................................... 11 Annex C (Informative)—Visual Acuity Record ........................................................................................................... 13 Annex D (Informative)—Requesting an Offcial Interpretation on an AWS Standard................................................. 15 Annex E (Informative)—List of AWS Documents on Qualifcation and Certifcation ................................................. 17

ix

AWS B5.2:201 8

This page is intentionally blank.

x

AWS B5.2:201 8

Specifcation for the Training, Qualifcation, and Company Certifcation of Welding Inspector Specialists and Welding Inspector Assistants 1. Scope 1.1

This specifcation establishes the minimum requirements for an employer’s (company’s) internal written practice

Welding Inspector Specialists and Welding Inspector Assistants. The employer is responsible for the testing, examination and qualifcation o f their inspectors. for the training, qualifcation, and that company’s certifcation o f

1.2

This specifcation is to aid employers in identi fying the basic factors in quali fying personnel performing welding

inspection for a specifc company or proj ect.

1.3 In developing the written practice (see Clause 7),

the employer shall review the detailed recommendations presented

herein and incorporate them into the practice, as applicable.

1.4

Examination and certifcation by the American Welding S ociety (AWS ) shall not be a requirement for the Welding

Inspector Specialist nor is there reciprocity between a Welding Inspector Specialist or Welding Inspector Assistant and AWS Certifed Welding Inspector (CWI) or Certifed Associate Welding Inspector (CAWI) in accordance with AWS QC1 ,

Specifcation for AWS Certifcation of Welding Inspectors.

1.5 Safety and health issues and concerns are beyond the scope o f this standard and therefore are not addressed herein. Safety and health information is available from the following sources: American Welding Society: (1 ) ANSI Z49. 1 ,

Safety in Welding, Cutting, and Allied Processes

(2) AWS Safety and Health Fact Sheets (3 ) Other safety and health information on the AWS website Material or Equipment Manu facturers: (1 ) Safety Data S heets supplied by materials manu facturers (2) Operating Manuals supplied by equipment manu facturers (3 ) Applicable Regulatory Agencies Work performed in accordance with this standard may involve the use o f materials that have been deemed hazardous, and may involve operations or equipment that may cause inj ury or death. This standard does not purport to address all safety and health risks that may be encountered. The user o f this standard should establish an appropriate safety program to address such risks as well as to meet applicable regulatory requirements. ANS I Z49. 1 should be considered when developing the safety program.

1

AWS B5.2:201 8

2. References 2.1 Normative References.

The following documents are referenced within this publication and are mandatory to

the extent specifed herein. For undated re ferences, the latest edition o f the re ferenced standard shall apply. For dated re ferences, subsequent amendments to, or revisions o f, any o f these publications do not apply. (1 ) ANSI Z49. 1 ,

Safety in Welding, Cutting, and Allied Processes

(2) AWS A3. 0M/A3 . 0, Standard Welding Terms and De fnitions, Including Terms for Adhesive Bonding, Brazing, Soldering, Thermal Cutting, and Thermal Spraying (3 ) AWS A2. 4,

Standard Symbols for Welding, Brazing, and Nondestructive Examination

(4) AWS B 5.1 ,

Specifcation for the Qualifcation of Welding Inspectors

2.2 Informative References (1 ) AWS QC1 ,

Specifcation for AWS Certifcation of Welding Inspectors

(2)

Brazing Handbook,

(3 )

Welding Handbooks, Volumes 1 –4, AWS

(4)

Welding Inspection Handbook,

AWS

AWS

3. Terms and Defnitions For the purposes o f this document, the following terms and defnitions apply:

certifcation. The act o f determining,

veri fying, and attesting in writing to the qualifcation o f personnel or organizations

in accordance with specifed requirements.

certifying offcial. The employee o f the company who is designated to certify inspectors and revoke certifcation. employer (company).

The corporate, private, or public entity which employs personnel for wages, salary, fees, or other

considerations.

qualifcation.

Demonstrated training, skill, knowledge and experience required for personnel to perform the duties o f a

specifc j ob or function, typically demonstrated by passing a performance test.

specifcation. Document stating requirements. training. An organized program developed to impart the knowledge and skills necessary for qualifcation. written practice.

A document to speci fy methods, requirements, examination, records, certi fying o ffcial, etc. , for a

company’s welding inspection personnel certifcation program.

4. Levels of Qualifcation There are two levels o f welding inspector qualifcation defned in this document. These are and

Welding Inspector Assistant.

Welding Inspector Specialist

4.1 Welding Inspector Specialist. A Welding Inspector Specialist is an individual who has been qualifed by the employer as meeting the requirements o f the employer’s welding inspector qualifcation program.

4.2 Welding Inspector Assistant. A Welding Inspector Assistant is an individual who has been qualifed by the employer as meeting the requirements o f the employer’s program to assist the Welding Inspector S pecialist in performing the defned duties. The Welding Inspector Assistant shall perform inspection duties under the supervision o f a Welding Inspector Specialist.

2

AWS B5.2:201 8

5. Functions In establishing a program, the employer shall state in the written practice the specifc functions to be carried out by the inspectors. As a minimum, the items in Annex A that are applicable to the company’s operations shall be incorporated into the written practice. The company methods for accomplishing each duty shall be defned. The specifc functions of the Welding Inspector Specialist and the Welding Inspector Assistant shall be defned in the written practice.

6. Education and Experience 6.1 The following are minimum requirements for each candidate for Welding Inspector Specialist. 6.1.1 The candidate shall be a high school graduate or hold an approved general equivalency diploma. 6.1.1.1 As an alternative to the requirements in 6.1.1, the employer may accept additional years o f experience in lieu of the education requirements. 6.1.2 The candidate shall have no fewer than fve years’ experience in an occupational function that has direct relationship to weldments being fabricated to a specifed code, other standard, or contract and shall be directly involved in one or more of the following functions:

(1) Design. Preparation of plans and drawings for weldment construction. (2) Production. Planning and control of welding operations such as procedures, equipment, materials, or personnel involved in weldment fabrication. (3) Construction. Performance as a welder, ftter, or other function in the fabrication or erection of weldments. (4) Inspection. Detection and measurement of weld discontinuities or verifcation of fabrication requirements. (5) Repair. Repair of weldments. 6.1.2.1 As an alternative to the requirements in 6.1.2, the employer may substitute an equal number o f years o f posthigh school education for required years of experience, provided the studies are directly related to the functions defned in 6.1.2.

Post high school education is defned as any of the following: (1) Associate or higher degree in engineering, engineering technology, physics, or sciences. (2) Engineering/technical school courses success fully completed in a curriculum that can be applied to (1) above. (3) Trade/vocational school courses in a curriculum related to welding. 6.1.3 The candidate shall submit written documentation that he/she meets the requirements o f 6.1.1 and 6.1.2 or the alternatives listed in 6.1.2.1. 6.2 The following are minimum requirements for each candidate for Welding Inspector Assistant: 6.2.1 The candidate shall be a high school graduate, or hold a state or military approved high school equivalency diploma (e.g., GED). 6.2.1.1 As an alternative to the requirements in 6.2.1, the employer may accept additional years o f experience in lieu of the education requirements. 6.2.2 The candidate shall have at least six month’s experience in an occupational function that has a direct relationship to weldments fabricated to a code or other standard (see 6.1.2).

3

AWS B5.2:201 8

7. Written Practice 7.1 The employer shall establish a written practice that details the job functions for welding inspectors, or the employer may use more than one written practice based on specifc inspection duties or products. The written practice shall also describe the education, experience, and training required for company certifcation. A sample outline for recommended practice is included as Annex B. 7.2 The written practice shall include topics, subjects, and training related to the inspection o f weldments fabricated to a

code, specifcation, or other standard as applied by the employer.

7.3 The written practice shall defne the company o ffcial who is authorized to certify inspectors and revoke certifcation.

8. Physical Requirements 8.1 Candidates must be physically able to safely perform the activities as required or specifed by the employer. The functions

to be performed by an inspector are defned in the employer’s written practice.

8.2 Vision 8.2.1 Near Vision Acuity: The Welding Inspector Specialist and Welding Inspector Assistant shall be tested for near vision acuity. The Welding Inspector Specialist and Welding Inspector Assistant shall have the ability to read Jaeger Number 2 letters or smaller at a minimum distance of 12 inches (or equivalent test) with at least one eye with or without correction. The Welding Inspector Specialist and Welding Inspector Assistant shall be retested for visual acuity every three years. 8.2.2 Color Perception: The Welding Inspector Specialist and Welding Inspector Assistant should take a color perception test. Note: Near vision acuity is considered essential to the proper performance of welding examination. Failure to meet the above level of visual acuity shall be a failure to meet the requirements of this specifcation. Color perception is desirable in some specifc applications, but is not considered essential for all examinations. It shall be the employer’s responsibility to establish and enforce visual requirements for its Welding Inspector Specialists and Welding Inspector Assistants.

9. Training Candidates to be considered for qualifcation and certifcation shall have received suffcient training to become thoroughly with the principles of welding inspection applicable to the practice to be used and the products to be inspected. Training shall include the specifcations, standards, or contract requirements applicable to the inspections being performed. It is the employer’s responsibility to determine the extent of the content and minimum number of hours of training required for a Welding Inspector Specialist and Welding Inspector Assistant. Training requirements shall be written into the company’s written practice. Training shall also address safety considerations and the proper care and use of tools and equipment when used. A recommended body of knowledge is provided in Annex A. familiar

10. Examination Requirements 10.1 Profciency Examination. The employer shall conduct initial examinations for new candidates and periodic updates for previously qualifed inspectors.

The examinations shall incorporate checkpoints or profciency demonstration to verify that the individuals possess the ability to perform specifc inspection and interpret results. Verifcation that the candidate met the minimum requirements of this standard shall be a permanent part of the employee’s records.

10.2 Welding Inspector Specialist Examination 10.2.1 The employer shall structure a test consisting o f three parts as defned below. Candidates shall achieve a minimum passing score, as determined by the employer, for each of the three parts. A minimum passing score of 70% or higher for each of the three parts is required.

4

AWS B5.2:201 8 10.2.2 The recommended examination shall consist o f an open-book test on industry standards or contracts applicable to the employer, closed-book test on welding fundamentals (including safety), and a test on practical applications o f welding inspection. See Annex A for recommended body o f knowledge.

10.3 Welding Inspector Assistant Examination 10.3.1 The employer shall structure a test consisting o f three parts as defned below. Candidates shall achieve a minimum passing score, as determined by the employer, for each o f the three tests. A minimum passing score o f 70% or higher for each o f the three parts is required.

10.3.2 The recommended examination shall consist o f an open-book test on industry standards or contracts applicable to the employer, closed-book test on welding fundamentals (including safety), and a test on practical applications o f welding inspection. See Annex A for recommended body o f knowledge.

11. Third Party Agencies At the option o f the employer, an outside agency may be engaged to provide assistance in training, qualifcation and examination services. In such instances, the employer is responsible to assure that training, qualifcation, and examination requirements are in accordance with this document.

12. Certifcation 12.1

It is the employer’s responsibility to certi fy that the Welding Inspector Specialist and Welding Inspector Assistant

meet the requirements o f the company’s written practice.

12.2 Course outlines and certifcation records shall be maintained on fle by the employer and shall contain records o f the certifed individual and copies o f written practices as required by Clause 7. These records shall be maintained during the time the inspectors are certifed and for three years after the termination o f the employee. These records shall contain as a minimum the following: (1 ) Name o f certifed individual (2) Statement indicating experience and completion o f training in accordance with employer’s written practice. (3 ) Verifcation that individual met the requirements prescribed in Clauses 8, 9, and 1 0, including copies o f applicable: Education and Experience certifcates, Visual Acuity Records, and Test records. (4) Signature o f certi fying o ffcial (5) Date(s) o f certifcation

13. Company Responsibilities Code o f ethics, responsibility to the public, conf ict o f interest, unauthorized practice, revocation o f certifcation, reinstatement, recertifcation, and termination shall be in accordance with the employer’s written practice.

Note: While the Welding Inspector Specialist and Welding Inspector Assistant have established credentials, company certifcation alone may not legally qualify the inspector to provide inspection service to the public. Building codes and regulations contract documents and other project specifcations may require that inspections to be performed by or under the direction of others, such as a qualifed third party agency, a qualifed professional engineer, or a welding inspector qualifed to AWS B5. 1 and certifed in accordance with AWS QC1.

5

AWS B5.2:201 8

This page is intentionally blank.

6

AWS B5.2:201 8

Annex A (Normative) Body of Knowledge This annex is part of this standard and includes mandatory elements for use with this standard.

A1. Introduction A1.1 Capabilities

(1) Judges quality (2) Interprets specifcation limitations and intent (3) Communicate results and makes reports to supervisor A1.2 Qualifcations

(1) Physical condition (2) Vision (3) Knowledge of welding (4) Knowledge of drawings, specifcations, specifc codes, and procedures used by the employer (5) Knowledge of testing methods (6) Experience (7) Education and training A1.3 Responsibilities

(1) General (2) Specifc company responsibilities (3) Personal and company safety practices

A2. Welding, Cutting, and Brazing Processes (1) Processes used in fabricating the product being inspected (2) Overview of each process (3) Discontinuities that may be encountered with each process

7

AWS B5.2:201 8

A3. Material Fundamentals (1) Weldability (2) Metallurgy (3) Chemistry (4) Mechanical (a) Tensile strength (b) Hardness (c) Toughness (5) Testing for mechanical properties (6) Metallographic tests

A4. Fabrication (1) Joint preparation (2) Joint ft up (3) Welding procedure specifcation (4) Welder qualifcation (5) Other fabrication documents

A5. Heat Treatment (1) Preheat (2) Interpass temperature (3) Postweld heat treatment

A6. Nondestructive Examination (1) Visual inspection (a) Application and acceptance standards (b) Tools and their use (2) Liquid penetrant testing (a) Procedures (b) Acceptance standards (3) Magnetic particle testing (a) Acceptance standards (b) Procedures

8

AWS B5.2:201 8

(4) Other testing and inspection (a) 100% sampling (b) Random sampling (c) Radiographic (d) Ultrasonic (5) Specifc company procedures

A7. Inspection Documentation (1) Verify dimensions (2) Verify written welding procedures (3) Verify welder qualifcation papers (4) Review NDE reports (5) Prepare narrative reports

A8. References (1) ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes (2) Brazing Handbook, AWS (3) Welding Handbooks, Volumes 1–4, AWS (4) Welding Inspection, AWS (5) AWS A3.0M/A3.0, Standard Welding Terms and Defnitions, Including Terms for Adhesive Bonding, Brazing, Soldering, Thermal Cutting, and Thermal Spraying (6) AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination

9

AWS B5.2:201 8

This page is intentionally blank.

10

AWS B5.2:201 8

Annex B (In formative) Sample Outline for Written Practice This annex is not part of this standard but is included for informational purposes only.

JOB FUNCTIONS A Welding Inspector Specialist (or assistant) employed by the performing the following Functions:

Company is responsible for

(1) (2) (3)

etc.

WRITTEN PRACTICE A Welding Inspector Specialist (or assistant) is responsible for complying with the following written practices: (1) (2) (3) (4)

QUALIFICATION AND CERTIFICATION Company Certifcation as a Welding Inspection Specialist (or assistant) is based on the individual presenting evidence of years of relevant experience combined with level of Education and meeting specifed Physical requirements.

PERSONNEL TRAINING Success fully completing training in the following: (1) hours practical. (see (2) hours practical. (see (3) hours practical. (see

consisting of consisting of consisting of

11

hours classroom combined with course outline) hours classroom combined with course outline) hours classroom combined with course outline) etc.

AWS B5.2:201 8

EXAMINATION Attaining a minimum passing score o f

on each o f the three parts o f the

Company Welding Inspection S pecialist Test.

CERTIFICATION RESPONSIBILITY is Responsible for Certi fying Welding Inspection Specialists ( or

assistants) for

the

Company and maintains applicable Records for each individual certifed. The Records are maintained for a minimum period o f

and are available for review upon request. Certifcation records shall be

audited for completeness and compliance with this standard on a

basis.

CERTIFICATION MAINTENANCE The performance o f Certifed Welding Inspector Specialists ( or assistants ) is monitored on a basis to veri fy continued profciency o f the individual.

12

AWS B5.2:201 8

Annex C (In formative) Visual Acuity Record This annex is not part of this standard but is included for informational purposes only.

Your Company Name VISUAL ACUITY RECORD

The applicant is required to pass an eye examination, with or without correction, to prove: near vision acuity on Jaeger J2, or equivalent, at 12 inches. In addition, they shall also take a color perception test for red/green and blue/yellow differentiation. Applicant’s Name Examination:

S.S. or ID number

Date of examination

Meets Without

Meets With

Eye Correction

Eye Correction

Does Not Meet

Near Vision

Jaeger J2 (or Equivalent)

❑

OR

❑

❑

OR

Distance of 12 inches (check only one) Color Perception

Red/Green Differentiation Blue/Yellow Differentiation

Meets

Does not meet

❑ ❑

OR OR

❑ ❑

I certify that the above named applicant demonstrated the vision capabilities indicated above.

Printed Name of Examiner

Signature

Date

Printed Name of Administrator

Signature

Date

13

AWS B5.2:201 8

This page is intentionally blank.

14

AWS B5.2:201 8

Annex D (In formative) Requesting an O ffcial Interpretation on an AWS Standard This annex is not part o f this standard but is included for informational purposes only.

D1. Introduction The following procedures are here to assist standard users in submitting success ful requests for o ffcial interpretations to AWS standards. Requests from the general public submitted to AWS staff or committee members that do not follow these rules may be returned to the sender unanswered. AWS reserves the right to decline answering specifc requests; i f AWS declines a request, AWS will provide the reason to the individual why the request was declined.

D2. Limitations The activities o f AWS technical committees regarding interpretations are limited strictly to the interpretation o f provisions o f standards prepared by the committees. Neither AWS staff nor the committees are in a position to o ffer interpretive or consulting services on (1 ) specifc engineering problems, (2) requirements o f standards applied to fabrications outside the scope o f the document, or (3 ) points not specifcally covered by the standard. In such cases, the inquirer should seek assistance from a competent engineer experienced in the particular feld o f interest.

D3. General Procedure for all Requests D3.1 Submission.

All requests shall be sent to the Managing Director, AWS Certifcation Department. For e ffcient

handling, it is preferred that all requests should be submitted electronically through certifcation@ aws. org. Alternatively, requests may be mailed to: Managing Director Certifcation Department American Welding Society 8669 NW 3 6 St, # 1 3 0 Miami, FL 3 3 1 66

D3.2 Contact Information.

All inquiries shall contain the name, address, email, phone number, and employer o f the

inquirer.

D3.3 Scope.

Each inquiry shall address one single provision o f the standard unless the issue in question involves two or

more interrelated provisions. The provision(s) shall be identifed in the scope o f the request along with the edition o f the standard (e. g. , D1 . 1 : 2006) that contains the provision(s) the inquirer is addressing.

15

AWS B5.2:201 8

D3.4 Question(s). All requests shall be stated in the form of a question that can be answered ‘ yes’ or ‘ no’ . The request shall be concise, yet complete enough to enable the committee to understand the point o f the issue in question. When the point is not clearly defned, the request will be returned for clarifcation. Sketches should be used whenever appropriate, and all paragraphs, fgures, and tables (or annexes) that bear on the issue in question shall be cited.

D3.5 Proposed Answer(s). The inquirer shall provide proposed answer(s) to their own question(s). D3.6 Background. Additional information on the topic may be provided but is not necessary. The question(s) and proposed answer(s) above shall stand on their own without the need for additional background information.

D4. AWS Policy on Interpretations The American Welding S ociety (AWS) B oard o f Directors has adopted a policy whereby all o ffcial interpretations o f AWS standards are handled in a formal manner. Under this policy, all o ffcial interpretations are approved by the technical committee that is responsible for the standard. Communication concerning an o ffcial interpretation is directed through the AWS staff member who works with that technical committee. The policy requires that all requests for an o ffcial interpretation be submitted in writing. Such requests will be handled as expeditiously as possible, but due to the procedures that must be followed, some requests for an o ffcial interpretation may take considerable time to complete.

D5. AWS Response to Requests Upon approval by the committee, the interpretation is an o ffcial interpretation o f the S ociety, and AWS shall transmit the response to the inquirer, publish it in the

Welding Journal

, and post it on the AWS website.

D6. Telephone Inquiries Telephone inquiries to AWS Headquarters concerning AWS standards should be limited to questions o f a general nature or to matters directly related to the use o f the standard. The

AWS Board Policy Manual

requires that all AWS staff

members respond to a telephone request for an o ffcial interpretation o f any AWS standard with the information that such an interpretation can be obtained only through a written request. Headquarters staff cannot provide consulting services. However, the staff can refer a caller to any o f those consultants whose names are on fle at AWS Headquarters.

16

AWS B5.2:201 8

Annex E (In formative) List of AWS Documents on Qualifcation and Certifcation This annex is not part o f this standard but is included for informational purposes only.

Qualifcation Designation

Title

B 5. 1

Specifcation for the Qualifcation of Welding Inspectors

B 5. 2

Specifcation for the Training, Qualifcation, and Company Certifcation of Welding Inspector Specialists and Welding Inspector Assistants

B 5. 4

Specifcation for the Qualifcation of Welder Test Facilities

B 5. 5

Specifcation for the Qualifcation of Welding Educators

B 5. 9

Specifcation for the Qualifcation of Welding Supervisors

B 5. 1 4

Specifcation for the Qualifcation of Welding Sales Representatives

B 5. 1 5

Specifcation for the Qualifcation of Radiographic Interpreters

B 5. 1 6

Specifcation for the Qualifcation of Welding Engineers

B 5. 1 7

Specifcation for the Qualifcation of Welding Fabricators

17

AWS B5.2:201 8

Certifcation Designation

Title

QC1

Specifcation for AWS Certifcation of Welding Inspectors

QC5

AWS Standard for Certifcation of Welding Educators

QC9

Administrative Procedures for Alleged Violations of AWS Certifcation Programs

QC13

Specifcation for the Certifcation of Welding Supervisors

QC14

Specifcation for the Certifcation of Welding Sales Representatives

QC15

Specifcation for AWS Certifcation of Radiographic Interpreters

QC17

Specifcation for AWS Accreditation of Certifed Welding Fabricators

QC19

Specifcation for AWS Certifcation of Robotic Arc Welding Personnel

QC20

Specifcation for AWS Certifcation of Resistance Welding Technicians

QC47

Specifcation for AWS Certifcation of Welders and Accreditation of Test Facilities

18