Loading documents preview...
1
2
3
4
5
6
7
8
Drawing Approval 9
7
5
3
1
6
2
4
8
10
Note: 2 pcs pulley required with extend shaft for speed sensor
AC
A
X
15
Plate thk. 6 mm
240
820
770
PT. Krakatau Engineering
PT. SUPRABAKTI MANDIRI
240 50
800
A
40
B
B
75
1000 1150
270
196
Free Side
Fix Side
AC 75 270
C/C Bearing Housing 1690
View AC - AC 61 20
1947
2 x Tap M10 - 20 mm deep
832
279
13
39
211
C
30°
100 h9
R4
0
279
1.6
140 h8
140h8
100h9
346
1.6 139.5
1.6
0
1.6
2
3
R4
D
This document must not be copied without written permission and the contents thereof must not be imported to a third party nor be used for any unauthorised purpose. Contravention will be prosecuted by Suprabakti Mandiri copyright. SUPRABAKTI MANDIRI - Engineering
C
11
DETAIL X SCALE 1 : 6
1947
D
LOCKING DEVICE :
GENERAL NOTES : 1.
- RINGFEDER RFN7012 : 140 x 190 TRANSMISSIBLE TORQUE = 20 kNm TRANSMISSIBLE BENDING MOMENT = 5.3 kNm MAXIMUM BOLT TIGHTENING TORQUE = 125 Nm
PAINTING : RAL 6002, 275 µM
- 150 µM PRIMER COAT - 50 µM INTERMEDIATE COAT - 75 µM TOP COAT
2. 3. 4.
WELDING USE AWS A5.20/SFA 75.1 PULLEY SHOULD BE STATICS BALANCING BALANCING WEIGHT NOT TO EXCEED 2% OF PULLEY SHELL & END DISCS MASS
E
9 Plummer Block (OE) FSNL 522-619 - Labirinth Seal (OE) 8 Plummer Block (CE) FSNL 522-619 - Labirinth Seal (CE) PLUMMER BLOCK SET: 7 Cover 250x141x5 6 Pulley Lagging ID : 800, Tebal : 10 FSNL 522-619 22222 EK 5 Locking Device 140x190 H322 4 Shaft 140 x 1947 FRB 13.5/ 200 3 stopper ring 250x141x15 TSN 522 S ASNH 522-619 2 End Disc 774/190x55 1 Pulley Shell 800x1150x15 ITEM Estimation weights pulley with plummer block : 879.73 Kg PART NAME DESCRIPTION NO.
TOLERANCE : UNLESS OTHERWISE SPECIFIED 1. 2. 3. 4.
Standard Diamond Groove
NOMINAL DIMENSIONS : +/- 1 2 DECIMAL PLACES : +/- 0.5 ANGLE : +/- 1 ALLOWABLE SHELL DIAMETER T.I.R 0.75 mm OVER BORE SHELL 0.75 mm OVER LAGGED SHELL
Tolerance
SUPRABAKTI MANDIRI, PT
GRAHA SUPRA Jl. Danau Sunter Utara Blok A, No. 9 Jakarta Utara 14350 Indonesia Phone : +62 21 658 33 666 Fax : +62 21 658 31 666 www.beltcare.com WORKSHOP Jl. Pasar Kemis Km. 3,5 Desa Kutajaya Pasar Kemis Tangerang 15560 Phone : +62 21 5903436-38 Fax : +62 21 5903747
F
D:\JOB PROJECT\Eka Adi Saputra\Project\Project 2014\PT. KE - Stocyard\Pulley Drawing Rev.1\NC5 & NC6\Tail Pulley\pulley standard
1
2
3
4
+/Surface Roughness
SBM-F-SESG-02c/00 10/02/08
mm
Approved by 10/13/2014 Checked by 10/13/2014 Drawn by 10/13/2014 Scale
Standard Standard SS400 SBR 50-60 Shore A Standard S45C SS400 SS400 SS400
1 1 2 1 2 1 2 2 1
MATERIAL
QTY.
E
F
Title
FN
Tail Pulley NC-5 & NC-6 PT. Krakatau Engineering - Harbour Stockyard
EAS Drawing No.
EAS
Reff. no.
SBM-38-09-14 Material
Qty
As Note
Unit
Paper
mm
A3
Rev
0