Me Laws

1. For violating RA 8495, the penalty is not less than P50,000 nor more than A. P100,000 B. P200,000 C. P150,000 D. P300,000 2. To be qualified to become a member of the Board of Mechanical Engineering the minimum age is A. 35 B. 40 C. 45 D. 32 3. Maximum plant capacity in which CPM is allowed to operate, tend or maintain: A. 200 kw B. 500 kw C. 300 kw D. 100 kw 4. Section 22 of the Republic Act No. 8495 "The Philippine Mechanical Engineering Act of 1988 " is about A. oath B. Issuance of Certificates of Registration and Professional License C. Re-examination D. Seal of a Professional Mechanical Engineer 5. The law that governs the practice of mechanical engineering is called: A. CA No. 194 B. RA No. 7920 C. RA No. 8495 D. RA No. 8995 6. To be responsible and in-charge in the preparation of plans and designs of a mechanical plant A. PME B. RME C. CPM D. CPM, RME and PME 7. Maximum plant capacity in which a licensed ME is allowed to operate, tend or maintain A. 300 kw B. 2000 kw C. 500 kw D. 6000 kw 8. For a mechanical plant with capacity of 100 kw or over but not more than 300 kw, the personnel required must be at least one

9.

10.

11.

12.

13.

14.

A. CPM B. PME C. RME D. CPM, RME and PME The PRC accredited national association for mechanical engineers A. ASME B. PAMEE C. PSME D. PICE The new Mechanical Engineering Law was signed last . A. February 12, 1998 B. February 6, 1998 C. January 18, 1998 D. February 12, 1998 The new Mechanical Engineering Law is a House Bill No. 9806 was finally passed by the House Representatives last . A. February 9, 1998 B. January 28, 1998 C. January 18, 1998 D. February 12, 1998 The new Mechanical Engineering Law is a Senate Bill No. 1793 was finally passed by the Senate last . A. February 14, 1999 B. January 12, 1998 C. February 3, 1998 D. January 28, 1998 To each professional subjects in mechanical engineering course unless the is a duly licensed A. PME B. Master's degree in ME C. any of these D. Doctorate degree holder in ME To be responsible charge of construction, erection, installation, alteration, or of the performance of a mechanical engineering service in connection with the manufacture, sale, supply or distribution of any mechanical works, unless he is duly registered: A. CPM B. Graduate of ME C. PME or RME D. Doctor of Education

15. 100 kw or over but not more than 300 kw, the personnel required in one CPM or one RME or one PME. Provided that every mechanical work in this category operating on more than shift every 24-hours A. three B. two C. four D. one 16. The new Mechanical Engineering Law has how many articles? A. two B. three C. five D. six 17. What are the contents in Article II? A. Board of Mechanical Engineering B. Statement Policy C. Term of Office D. Examination, Registration and License 18. What are the contents in Article III? A. Board of Mechanical Engineering B. Practice of the Profession C. Examination, Registration and License D. Term of Office 19. The Board of Mechanical Engineering is composed of members to be appointed by the President of the Philippines. A. one B. three C. two D. five 20. One of the following is not a correct qualification of Members of the Board: A. Natural born citizen and resident of the Philippines B. Must be at least 35 years old C. A PME with a valid professional license and an active practitioner for not less than 10 years D. Has been convicted of any offense and moral turpitude 21. A member of the board shall hold office for alarm of years from the date of his appointment. A. three B. two C. one D. four

22. No member of the Board shall serve for more than regular terms. A. one B. two C. three D. none of the above 23. Which of the following is/are the powers and duties of the Board? A. To supervise the registration, licensure and practice of mechanical engineers in the Philippines B. To issue the certificate of registration to successful examinees C. Approve, issue, limit or revoke temporary license to practice mechanical engineering D. All of these 24. One of the qualification of applicants for Professional Mechanical Engineer must be: He has specific record of a total of or more than 1 of active mechanical engineering practice. A. two B. three C. four D. five 25. One of the qualification of applicants for Professional Mechanical Engineer must be: He is competent to practice, attested to by at least Professional Mechanical Engineers. A. one B. two C. three D. many 26. Section 34 in the Mechanical Engineering Law is about: A. Preparation of Plans B. Personnel required in Mechanical Plant C. Field of Action D. Renewal of License 27. Section 24 in the Mechanical Engineering Law is about: A. Seal of Professional Mechanical Engineer B. Revocation and Suspension of Certificate C. Integration and Accreditation of ME D. Grounds for Suspension 28. Section 42 in the Mechanical Engineering Law is about: A. Penalties B. Oath C. Title

29.

30.

31.

32.

33.

34.

35.

36.

D. Statement of Policy The mechanical engineering law is composed of _ sections. A. 68 B. 48 C. 54 D. 35 Section 15 in the Mechanical Engineering Law is about: A. Qualifications of Applicants for Mechanical Engineer B. Qualifications of Applicants for CPM C. Qualifications of Applicants for PME D. None of the above The new Mechanical Engineering Law is a consolidation of the Senate Bill Nos. A. 1792 and 8806 B. 1893 and 9912 C. 1993 and 9907 D. 1793 and 9806 Republic Act 8495 known as the Mechanical Engineering Act of 1998 was approved last A. Feb. 12, 1998 B. Feb. 3. 1998 C. Jan. 26, 1998 D. Feb. 25, 1998 At section 35 of the ME Law, pressurized pipes will have a working pressure of not less than? A. 150 kPa B. 95 kPa C. 100 kPa D. 70 kPa The PSME was established in what year? A. 1945 B. 1970 C. 1952 D. 1998 PSME is one of the accredited organization in the Philippines with a Certificate No. of A. 001 B. 004 C. 002 D. 010 The exact period when the Mechanical Engineering Law begun and held in Manila during the third regular session of the tenth congress. A. July 28, 1997

37.

38.

39.

40.

41.

42.

43.

B. Feb. 4, 1998 C. August 20, 1997 D. Feb. 21, 1998 What are the contents in Article I? A. ME Laws B. Title, Statement of Policy and Definition of Terms C. Contents of ME Law D. Board of ME What are the contents in Article V? A. Final and Conclusion B. Penal and Concluding Provisions C. Penalties D. Transitory Provisions What are the contents in Article IV? A. Practice of Profession B. Personnel required in Mechanical Plant C. Preparations of Plans D. Posting of Certificate Which of the following Ware required to secure a Temporary/special Permit from the Board of Mechanical Engineering: A. Mechanical Engineers from other countries called in for consultation B. Foreigners employed as technical officers C. Foreigners employed as consultants in such installation D. All of these In section 18, to pass the examination a candidate must obtain with no rating below percent in any of the subjects and obtain an average of percent on all subjects. A. 70 %, 50% B. 50 %, 70% C. 75 %, 60% D. 50 %, 75% In section 41, where a position requires a Professional Mechanical Engineer license a holder of a with a registered mechanical engineer’s license shall be considered for the position. A. master’s degree in ME only B. doctorate degree in ME only C. master’s or doctorate degree in ME D. NOTA In section 41, a government or private institution where a position requires a master’s degree holder, a holder of license shall be eligible the position. A. PME

44.

45.

46.

47.

48.

49.

B. RME C. CPM D. PME, RME, or CPM In section 6, a member of the board shall hold office for a term of 3 years from the date of his appointment and no member of the board shall serve for more than regular terms. A. one B. three C. two D. four In section 6, any vacancy occurring within the term of a member due to some cause, shall be filled by appointment by the President of the Philippines and such member appointed shall serve for the unexpired portion of the term vacated without prejudice to serve for a maximum of full terms. A. one B. three C. two D. four What is the minimum pipe working pressure to be considered as mechanical equipment? A. less than 70 MPa B. 70 kPa C. 60 kPa D. 40 kPa One of the most important qualification for PME, that he is competent to practice as attested by at least . A. two PME B. one PME C. two ME D. one CPM The Rules and Regulations Implementing the Philippine Mechanical Engineering Act of 1998 are formulated and issued pursuant to-what article of RA 8945? A. Article V B. Article I C. Article VI D. Article II OTEC means: A. Organization of Technical Engineers Countrywide B. Ocean Thermal Energy Conversion C. Ocean Thermal Energy Conservation D. Ocean Technical Engineers Corporation

50. What is meant by the term Board? A. Chairman of the Board B. Chairman of the Committee C. Board of Mechanical Engineering D. PRC Board 51. In the guidelines for applicants in Professional Mechanical Engineer, the following papers must be submitted, (1) Affidavit of the applicant, (2) Certificate of experience, (3) List of designs and (4) Certificate of Competence under oath by a . A. RME B. PME C. CPM D. Manager 52. Which of the following refers to as a practice of Mechanical Engineering? A. Project studies of any mechanical projects B. All of these C. Management of the installation of mechanical projects. D. Management of the sale of mechanical parts 53. Which of the following is NOT a qualification of the Members of the Board? A. Must not, for a period of 5 consecutive years be a member of the faculty of any institution B. Has never been convicted of any offense C. A Professional Mechanical Engineer D. An active practitioner for not less than 10years prior to his appointment 54. One of the most important qualifications fro Professional Mechanical Engineer is to have a specific record of a total of years or more of active mechanical engineering practice. A. 2 B. 5 C. 3 D. 4 55. The seal of PME is in a form of a gear with a 40 mm diameter outer circle 20 mm diameter inner circle. Inside the lower circular band shall be inscribed, the words A. Mechanical Engineer B. Official Seal C. Name of the Professional D. Registration Number 56. What is meant by Commission Chairman? A. PRC Commissioner B. Chairman of the Board C. Chairman of the CHED D. Chairman of the CPE

57. An important guideline for applicants in Professional Mechanical Engineer Examination is to require the applicant to present himself before at least two members of the board for interviews. A. Three B. Single C. Four D. Two 58. In the evaluation of the experience of applicants in PME examination, the following should be considered: design experience, maintenance and operation, fabrication and shop practice and . A. Management B. Operation C. Employment D. Installation 59. In the Meetings of the Board, in the absence of the chairman, which of the members will preside? A. Two members B. Senior member C. Commissioner D. Assistant Commissioner 60. It Is the unification of all mechanical engineers including CPM into one national organization of mechanical engineers. A. Engineering firm B. Engineering management C. Consultation D. Integration 61. In section 7 of the implementing rules and regulations, a member of the board, shall hold office for a term of years from the date of his appointment. A. Two B. Four C. Three D. Six 62. What are the contents in Rule V? A. Licensure examination for the practice of mechanical engineering B. Administrative proceedings C. Miscellaneous provisions D. Practice of Mechanical Engineering 63. In the implementing rules ad regulation, what is the content in section 24? A. Definition of Terms

64.

65.

66.

67.

68.

69.

70.

B. Issuance of Certificates of Registration C. Scope of Examination D. Renewal of Professional License The official Seal of the Board is represented by drawing of: A. Gear B. Hero’s Steam Engine C. Spherical Kettle D. Internal Cylinder In section 28, to pass the examination, a candidate for PME, RME nd CPM must obtain an average of percent in all subjects with no rating below percent in any of the subjects. A. 70 %, 70 % B. 50%, 70% C. 70%, 60% D. 70 %, 50% Which of the following is/are grounds for the revocation of Professional Certificates? A. Use of any fraud in obtaining certificate B. Negligence C. All of these D. Violation of the policies of the board The Board of Mechanical Engineering Is composed of: A. One chairman and a member B. Three members C. one chairman and two members D. Five members Which of the following is NOT a qualification of the Members of the Board? A. Resident of the Philippines B. Holder of the degree of BSME C. Must be at least 35 years old D. Must be a national officer of the PSME The seal of a PME is in a form of a gear with a 40 mm diameter outer circle and 20 mm diameter inner circle, inside in the upper circular band shall be inscribe the words A. Professional Mechanical Engineer B. Registered Professional C. Mechanical Engineer D. Professional Engineer In the implementing rules and regulations, what is the content in section 31? A. Full Computerization of Examination B. Renewal of Professional License C. Qualifications of the Board

D. Transitory Provisions 71. What is the content in Rule 11? A. Statement of Policy B. Effectivity C. Grounds for the Suspension D. Official Seal of the Board 72. The title of Resolution No. 16 series of 1998 is: A. Code of Ethics of Mechanical Engineers B. Philippines Mechanical Engineering Code C. Rules and Regulations Implementing RA 9495 D. Mechanical Engineering Act of 1998 73. Which of the following is NOT considered a mechanical equipment? A. Xerox Machine B. Fired Pressure Vessel C. Internal Combustion Engines D. Crane 74. What is the content in section 43? A. Seal of a Professional Mechanical Engineer B. Code of Ethics C. Teaching of Mechanical Engineering Subjects D. Report of the Board 75. The Rules and Regulations Implementing the Philippine Mechanical Engineering Act of 1998 are formulated and issued pursuant to what section of RA 8945? A. Section 5 B. Section 49 C. Section 10 D. Section 43 76. The seal of a Professional Mechanical-Engineer is in the form of a: A. Kettle B. Gear C. Pressure Vessel D. Machine 77. The seal of a PME is in a form of a gear with a 40mm diameter outer circle and 20 mm diameter inner circle. A rectangular band placed horizontally across the center of the gear is the . A. Registration Number B. Name of the Professional C. Official Seal D. Company Name

78. In the Code of ethics for Mechanical Engineers in the Philippines, Rule No. 5 states that “ The mechanical engineer shall honor and respect the supreme authority of the state, the rule of law, the obligations and privileges of citizens recognized and guaranteed by the Constitution, of the Philippines” This statement is for our relation with . A. The state B. Labor C. The community D. Employers 79. In the Code of ethics for Mechanical Engineers in the Philippines, Rule No. 14 states that “ He shall strive to improve the skills of his workmen, pay them a fair living wage, and instruct then on hw to prevent accidents in their place of work” This statement is for our relation with . A. Labor B. Client C. Safety D. Associates 80. In the Code of ethics for Mechanical Engineers in the Philippines, Rule No. 18 states that “The mechanical engineer is entitled to a just and fair compensation for his services” This statement is for our relation with . A. Client and Employers B. Employers only C. Colleagues and Associates D. Salary and Wage