Schindler Escalator And Moving Walk: Troubleshooting Guide Q 43831001_00 Edition 10-2014

Schindler Escalator and Moving Walk Troubleshooting Guide Q 43831001_00 Edition 10-2014

Prepared

naidura

28.08.2014

Lead Office

Classification

Document Owner

Reviewed

laeuffpe

04.09.2014

SC7

11XXX

Norms checked

plattle

03.10.2014

INVENTIO AG, CH-6052 Hergiswil

Released

ludwigj2

11.10.2014

Modification:

00

KA No.:

107490

KA Date:

11.10.2014

Copyright © 2014 INVENTIO AG All rights reserved. INVENTIO AG, Seestrasse 55, CH-6052 Hergiswil, owns and retains all copyrights and other intellectual property rights in this manual. It shall only be used by SCHINDLER personnel or authorized SCHINDLER agents for purposes which are in the interest of SCHINDLER. Any reproduction, translation, copying or storing in data processing units in any form or by any means without prior permission of INVENTIO AG is regarded as infringement and will be prosecuted.

Table of Contents Table of Contents

1

2

3 4

5

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Protective Clothing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 Personal Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification of Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 SW, SW 77, SWE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 SDS, SDG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 S 9300, S 9500, S 9700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Mechanical Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Electrical Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Customer/Protective Barriers/EoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Floor Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Maintenance Operating Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 Guard Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6 Maintenance Steps/Pallets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 Handrail Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8 Combplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9 Step Level Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Relay Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 MICONIC F 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 MICONIC F 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 MICONIC F 3/4/5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents Copyright © 2014 INVENTIO AG

Q 43831001_00

4 4 5 6 12 13 14 15 15 16 17 18 18 20 29 29 31 32 33 35 36 40 41 45 46 46 49 54 60

3

1 1.1

General Information Introduction

The purpose of this troubleshooting guide is to provide the Schindler employee with an appropriate tool to make troubleshooting work easier. Only properly trained and authorized Schindler employees are permitted to operate or handle any portion of the equipment. This also applies to settings, adjustments, inspections, maintenance, repair and modernization.

The given instructions are for escalator and moving walks. To keep this troubleshooting guide as slim as possible only the wording “step” and “step axle” are used. At a moving walk with short pallets remove three pallets instead of one step. At a moving walk with long pallets proceed as described for steps.

This troubleshooting guide does not claim to include all possibilities. The Schindler employee has to read, understand and follow the instructions in this troubleshooting guide in any case. Do not disclose this troubleshooting guide to third parties. Return the troubleshooting guide to the line manager when requested. For any questions and suggestions please contact your local branch office or national master trainer.

General Information Copyright © 2014 INVENTIO AG

Introduction

Q 43831001_00

4

1 General Information 1.2 Safety Warnings The following types of safety warnings are used in the present manual. DANGER Danger The safety warning with the signal word “Danger” is used to indicate a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING Warning The safety warning with the signal word “Warning” is used to indicate a hazardous situation which, if not avoided, could result in death or serious injury.

NOTICE Notice The safety warning with the signal word “Notice” is used to address practices that could lead to property damage but not to injury.

General Information Copyright © 2014 INVENTIO AG

Safety Warnings

Q 43831001_00

5

1 General Information 1.3 Safety Guidelines DANGER Accidents or Operating Errors

DANGER Maintenance Operating Panel

Accidents or operating errors will lead to serious injury to persons and/ Before entering the pit: or damage to property. – Connect the maintenance operating panel Every precaution should be taken to prevent accidents and incorrect – Check the proper function of the movement – Activate the emergency stop button operation. – Check that no movement is possible. DANGER DANGER

Unexpected Movement of the Escalator Test Runs

Unexpected movement of the escalator will result in serious injury or death. Test runs during work performed on the unit represent an increased risk Lock out and tag out the main switch JHA while working inside the step to persons and components of the unit. In the course of work performed at the escalator or moving walk, trial band. runs should only be carried out with the maintenance operating panel. DANGER DANGER

Unexpected Movement of the Escalator Emergency Stop Button

Unexpected movement of the escalator will result in serious injury or death. As a matter of principle, always press the emergency stop button at the Always press the emergency stop button JHRE as long as the unit must location where work takes place. not be moved. This will prevent starting the unit by mistake.

General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

6

1 1.3

General Information Safety Guidelines DANGER

WARNING

Hazardous Voltage

Bypassing of Safety Devices and Safety Contacts

Contact with live parts will result in electric shock causing serious injury Any bypassing of safety-relevant devices could result in damage to the or death. installation or in serious injury or death. Take the following precautions:  Bypassing the safety circuit without explicit instruction is  Do not touch live parts. prohibited.  Switch off the main switch JHA before starting to work on the unit.  Always take appropriate safety measures if premeditated bypassing is necessary for specific work on the installation.  Do not use bypassing of the safety devices if prohibited by local WARNING code. Local Health and Safety Regulations  Always leave the installation with all bypassing disabled. Ignoring health and safety regulations could result in damage to the installation or in serious injury or death. WARNING Strictly follow the local health and safety regulations, which apply in No Passengers on the Unit During a Technical Test addition to the minimal health and safety regulations specified in this Passenger on the unit while running a technical test could result in manual. death or serious injury. Do not allow any passengers on the unit while running a technical test. WARNING Unauthorized Access Secure the unit against accidental or unauthorized access. Set up warning signs and barriers to alert passengers to the fact that the unit is not in use.

General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

7

1 General Information 1.3 Safety Guidelines Escalators with hollow step axles are identified by stickers on the guard plates.

NOTICE Do NOT Step onto the Hollow Step Axles If the escalator is equipped with hollow step axles, do not step directly onto the step axles. Observe the sticker in the escalator pit. Never step onto the step axles in the inclined section of the step band.

Since release of the EN115-1:2008 a “emergency service” with bridged safety relevant components like switches or sensors at units which were commissioned since 2008 is not permissible anymore. Controller older than MIC F 2: Supply voltage of safety circuit is 230 VAC. Controller MIC F 2/3/4/5: Supply voltage of safety circuit is 110 VAC or 24 VDC.

[45386; 01.05.2013]

General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

8

1 General Information 1.3 Safety Guidelines The Following Five Safety Rules must be Observed NOTICE

1

Electrostatic Sensitive Device Printed Circuit Boards (PCB) are equipped with electrostatic sensitive semiconductors. Thus beware of electrostatic discharge and direct contact with the semiconductors.  Touch the control cabinet to ground yourself for electrostatic discharge.  Do not directly touch the PCB components.  Always use the original antistatic packing when transporting the PCBs.

2 3 4 5

Before starting installation work, put up barriers to protect passersby and "Out of Order" signs (if hinged floor covers are used, they must be properly opened and locked). As soon as a floor cover has to be removed (or folded up) and before entering the pit, connect the maintenance operating panel. Perform all trial runs with the maintenance operating panel. When carrying out maintenance work inside the step/pallet band, switch off and lock the main switch. Never turn on escalators or moving walks under load.

Only appropriate tools, devices and materials may be used. The specifications on the safety data sheet for lubricants (oils, greases, etc.) must be met.

General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

9

1 General Information 1.3 Safety Guidelines Turning by Hand WARNING Risk of Injury from Flywheel

1

Fingers might get hurt by the flywheel. Do not stick fingers under the flywheel.

10004259

 Loosen the safety brake (1), if fitted.  Loosen the service brake (2).  Turn the flywheel (3). - The correct direction of rotation is indicated on the flywheel (3).

[29429; 26.06.2009]

1 2 3

Safety brake Service brake Flywheel

[46381; 21.12.2012]

General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

10

1 General Information 1.3 Safety Guidelines Safety Equipment

Industrial Helmet

Safety Goggles

Full Body Harness

Safety Shoes

Protective Gloves

Hearing Protection

All people involved must know and follow the company and local safety regulations. Protective clothing and appropriate safety equipment must be worn. General Information Copyright © 2014 INVENTIO AG

Safety Guidelines

Q 43831001_00

11

1 General Information 1.4 Protective Clothing 1 2 3 4 5 6

1 2 3

Industrial helmet Safety goggles Dust mask Kevlar sleeves Protective gloves Safety shoes

4 5

6 [29410; 23.07.2010]

General Information Copyright © 2014 INVENTIO AG

Protective Clothing

Q 43831001_00

12

1 General Information 1.5 Personal Protective Equipment Designation

Quantity

Dust mask

1

Safety goggles

1

Protective gloves, size “M”

ID. No. 50639223

1

Protective gloves, size “L”

ID. No. 50639224

1

Kevlar sleeves

ID. No. 50639221

1

Industrial helmet

1

Safety shoes

1

Safety lock

1

Safety harness

1

Reflective jacket

1

Hearing protection

1

First aid kit

1

General Information Copyright © 2014 INVENTIO AG

Personal Protective Equipment

Q 43831001_00

13

1 General Information 1.6 Abbreviations Abbreviation _ ∗ [∗∗] or [∗∗∗∗] [∗∗∗∗]/[∗∗∗∗] BMS Bus EoS MIC FCOM Flash Jumper PCB PA PB PT P2 P3 PEM50.Q PEM51.Q PEM52.Q PF1.Q General Information Copyright © 2014 INVENTIO AG

Abbreviation Blank space Wildcard character Display MICONIC F 5S or F 5E Alternating display Building management system Communication system Engineer on Site MICONIC Maintenance software Program, parameter and error memory Bridge between two male connectors Printed circuit board PCB in the external control cabinet PCB in the bottom control cabinet PCB in the top control cabinet PCB, contract-specific position PCB, contract-specific position PB for MICONIC F 5S PT for MICONIC F 5S PCB for MICONIC F 5E PCB for MICONIC F 1, F 2

Abbreviation

Explanation

RAM

Random access memory

RS-232

Interface for FCOM or BMS

RS-485 X2.9 - 13 Interface for connecting of PCBs

Abbreviations

RS-485 X5.1 - 4

Interface for BMS or ALCDG

SEMI5-Card

Memory card with access rights

0x0000

Number in hex format

T

Top

B

Bottom

L

Left

R

Right

M

Middle

Q 43831001_00

14

2 2.1

Identification of Units SW, SW 77, SWE The type of unit can be identified by the specific handrail entry. A B C

A [49166; 22.10.2013]

SW: Relay control, no handrail entry contacts SW: Relay control, handrail entry “mouse trap” SW77: Relay control, handrail entry “mouse trap”

B [49153; 21.10.2013]

C [49152; 21.05.2014]

Identification of Units Copyright © 2014 INVENTIO AG

SW, SW 77, SWE

Q 43831001_00

15

2 Identification of Units 2.2 SDS, SDG The type of unit can be identified by the specific handrail entry. A, B SDS: MICONIC F 2 control C

A [49169; 23.10.2013]

SDG: MICONIC F 2 control

B [49156; 21.10.2013]

C [49155; 21.10.2013]

Identification of Units Copyright © 2014 INVENTIO AG

SDS, SDG

Q 43831001_00

16

2 Identification of Units 2.3 S 9300, S 9500, S 9700 The type of unit can be identified by the specific handrail entry. A, B S 9300, S 9500: MICONIC F 3, F 4, F 5 control C

A [49159; 22.10.2013]

S 9300, S 9500, S 9700: MICONIC F 3, F 4, F 5 control

B [49161; 25.10.2013]

C [49164; 22.10.2013]

Identification of Units Copyright © 2014 INVENTIO AG

S 9300, S 9500, S 9700

Q 43831001_00

17

3 Components 3.1 Mechanical Components 28 27a

29

28

27b

29

1

26

3 4

25a 24

24

6

23

7

22

22 21

8 9

21

2 3 4 5 6

25b

5

23

1

26

2

7 8

20

20

9

11a

10 18

11b

12

12 13

13 14a

14b

15 15 17

16

17

Components

3

Motor

4

Gearbox

5

Drive chain

6

Drive shaft with optional safety brake

7

Handrail drive

8

Pressure belt / pressure chain

9

Handrail tensioning device

10

Lateral cladding

12

Truss

13

Handrail entry

14a Step chain tensioning device 14b Pallet chain tensioning device 15

Truss soffit

16

Combplate

17

MICONIC F 2, F 3, F 4, F 5 control cabinet

18

Newel chain

16 [49168; 11.04.2014]

Copyright © 2014 INVENTIO AG

Service brake

11b Pallet chain

10

18

Flywheel

2

11a Step chain

19

19

1

Mechanical Components

Q 43831001_00

18

3 Components 3.1 Mechanical Components 28 27a

29

28

27b

29

1

26

3 4

25a 24

24

6

23

7

22

22 21

8 9

21

2 3 4 5 6

25b

5

23

1

26

2

7 8

20

20

9

10 11a

18

Outer decking

20

Inner decking

21

Skirt panel

22

Handrail

23

Balustrade

24

Balustrade clamps

25a Steps 25b Pallets 26

Combplate lighting

27a Balustrade profile (design E) 27b Balustrade profile (design F)

19

19

19

10 18

28

Floor covers

29

Control cabinet

11b

12

12 13

13 14a

14b

15 15 17

16

17 16 [49168; 15.08.2014]

Components Copyright © 2014 INVENTIO AG

Mechanical Components

Q 43831001_00

19

3 Components 3.2 Electrical Components

TL

T

TR ML M MR

Top

TL

Top Left

TR

Top Right

B

Bottom

BL

Bottom Left

BR

Bottom Right

M

Middle

ML

Middle Left

MR

Middle Right

A

Additional

A

BL

B

T

BR

Electrical Components Overview [43831001_001; 19.05.2014]

Components Copyright © 2014 INVENTIO AG

Electrical Components

Q 43831001_00

20

3 Components 3.2 Electrical Components Abbreviation

Area

ALCDG CBA

T

D DH DH1

Component

Abbreviation

Area

Component

Graphic plain text display

GLMGB

Safety brake capacitor

GPH

Diode

GV

Blocking valve

HK

Radiator

HS

Heating element

BR, M, TL Stop button

Safety brake rectifier T

Soft starting device

DIG

Digital display

HWD-relay

DJH

Push button for triggering the main switch

INAK

TL, TR

Hardware watchdog

INBB

TL, TR

Brake lining monitor

DH-BO

Stop button provided by client

INBMG

TL, TR

Motor speed monitor

DH-BS

Stop button, building site

INHL

BL, BR

Handrail speed monitor

DHEN

For maintenance panel

INMH

TL, TR

Motor speed monitor

DRE

Inspection push button up, down

INVK

B, T

Step speed monitor

DRES

Reset key

IRAD

BR, TL

Radar for entrance monitoring

DS

Start button

ITH

B, T

PT 100 temperature sensor

G

Rectifier

IZ

T

Pulse counter

GBMW

Braking distance measurement device

Drive chain monitor

JA

T

Deactivation switch

GFU

T, A

Frequency converter

JB

T

Switch for brake release

GFU-C

T

Frequency converter, crawling

JD

T

Continuous operation switch

GFUP

T, A

Frequency converter Plus

JF1

T

Residual current circuit breaker

Manual control device inspection

JFIH

T

Main circuit fault current breaker

GHRE Components Copyright © 2014 INVENTIO AG

Electrical Components

Q 43831001_00

21

3 Components 3.2 Electrical Components Abbreviation

Area

JFIL

T

JHA

T

JHHE

T

JHL JHRE JH-US

Component

Abbreviation

Component

T

Brake contact

Main circuit breaker

KBB

T

Brake lining contact

Heating switch

KBF

B, T

Contact in case of fire by customer

T

Main lighting system switch

KBFM

B, T

Smoke detector

B, T

Inspection stop switch

KBSA

T

Safety brake active contact

B

Return station stop switch

KBSP

T

Safety brake passive contact

KBW

BR, BL

Handrail monitoring contact

KBZ

T

Additional brake contact

KDH

BR, TL

Stop push button cover contact

KDMR

B, T

Floor cover contact / Machine room cover contact

JH JH1

Area

KB

B, M, T

Stop button

JH2 JL

B, T

Pit lighting switch

JMo

T

Motor switch

JMZS

T

Motor automatic lubrication switch

KDZS

T

Automatic lubrication pressure contact

JRE

B, T

Inspection switch

KF

T

Speed regulator contact

KGGFU

T, A

Frequency converter in generator mode contact

JREM

B, T

Stop switch

JR

B, T

Direction key switch

JRES

B, T

Key switch reset

JS

B, T

Key switch

JSK

Safety circuit switch

KAK

TL, TR

Drive chain contact

KANK

T

Missing-step check contact

Components Copyright © 2014 INVENTIO AG

KGL

Glass cladding monitor

KHL

BR, BL

Handrail contact

KHLA

BR, BL

Handrail displacement contact

KHLE

BL, BR, TL, TR

Handrail entry contact

Electrical Components

Q 43831001_00

22

3 Components 3.2 Electrical Components Abbreviation

Area

Component

Abbreviation

Area

Component

KHLL

BR, BL

Handrail elongation contact

KTBB

KKA

B, T

Step broken contact

KTHM

T

Thermo motor contact

KKB

TR, TL

KTHR

T

Thermo controller contact

KUS

BL, BR, TL, TR

Step upthrust monitoring contact

LAG

B, T

Direction indicator green

LAR

B, T

KKE KKP

Broken drive chain contact

Balustrade lighting door contact

BL, BR, TL, TR

Combplate contact

BL, BR, TL, TR

Combplate contact horizontal

KKPV

BL, BR, TL, TR

Combplate contact vertical

LG

KKS

BL, BR

Step/pallet chain tension contact

LHL

Mat pressure contact

LKPE

BL, BR, TL, TR

KKPH

KMD

LBB

Direction indicator red Balustrade lighting

B, T

Machine room lighting / pit lighting lamp Handrail check lamp Combplate lamp

KMs

T

Anti-reversing lock contact

KOZS

T

Automatic lubrication oil level contact

LMG

T

Motor noise choke

KRL

T

Anti-reversing contact

LNF

T, A

Interference suppression filter

KSEIS

B, T

Seismic monitor

LSS

B, T

Step gap lamp

KSL

BL, BR, TL, TR, ML, MR

LV

M

Light curtain

Skirt contact

MB

T, A

Motor brake

KSOFU

T, A

Frequency converter fault contact

MF

T, A

Motor filter

KTHWFU

M, A

Braking resistor

MGBA

T

Solenoid safety brake

Components Copyright © 2014 INVENTIO AG

Electrical Components

Q 43831001_00

23

3 Components 3.2 Electrical Components Abbreviation

Area

Component

Abbreviation PHANK

Area

T

Solenoid brake passive

MGBZ

T

Solenoid brake supplement

MGRL

T

Anti-reversing solenoid

PHGPH

Photoelectric cell phase angle control Photoelectric cell step receiver

MGS

T

Solenoid valve lubrication

PHKE

MGP

T

Piston pump

PHKS

B, T

Component

MGBP

Photoelectric cell / proximity switch missing-step check

Photoelectric cell step transmitter

MGSKA

T

Drive chain lubrication valve

PHS

B, T

Skirt panel photocell

MGSKHL

T

Handrail drive chain lubrication valve

PHSE

Photoelectric cell skirting receiver Photoelectric cell skirting transmitter

MGSKS

T

Step chain lubrication valve

PHSS

MH

T

Main drive motor

PHSTE

MJH

T

Main switch trigger solenoid

Photoelectric cell passenger guide bars receiver

Mo

T

Motor

PHSTS

Photoelectric cell passenger guide bars transmitter

MS

T

Anti-reversing solenoid

MVEH

T

Fan motor heating

MZS

T

Motor automatic lubrication

NGLBB

B, T

Balustrade LED lighting power supply

P

B, T

Socket

PBL

B, T

Dummy inspection connector

PCBA PGH

Components Copyright © 2014 INVENTIO AG

Capacitor safety brake B, T

PHVE

B, T

PHVS

B, T

Scan sensors transmitter

PMVEH

T

Heating fan motor connector

PRE

B, T

Inspection socket

P-AS

T

Socket drive station

P-US

B

Socket return station

R

Manual control unit connector

RB

Electrical Components

Scan sensors receiver

Ballast resistor T

Relay service brake Q 43831001_00

24

3 Components 3.2 Electrical Components Abbreviation

Area

Component

Abbreviation

Area

Component

RBGA

T

Relay safety brake

RKL

T

PTC resistor

RBL

B, T

Relay lighting

RKPH

T

Relay phase monitoring

RBLD1

B, T

Relay activation delay illumination 1

RKPV

B, T

Combplate relay vertical

RE

T

Switch-on contactor circuit

RKu

T

Auxiliary relay to changeover relay

RFPH

T, A

Phase error relay

RLAG

B, T

Relay direction indicator green

RFUS

T, A

Relay selection speed

RMBth

T

RGBA

T

Relay safety brake

Thermal solenoid brake protection relay

RGF

T, A

Output relay electrical regulated brake down, up

RMGB

T

Safety brake relay

RMGSKA

T

Drive chain lubrication relay

RHBS

Relay stop by customer

RMGSKHL

T

Handrail drive chain lubrication relay

RHM

Relay signalling stop

RMGSKS

T

Step chain lubrication relay

RIZHL

Pulse counter relay handrail

RMGSP

T

Lubrication pump relay

RJH

T

Main contactor

RN

T

Voltage monitoring relay

RK

T

Auxiliary relay

RPHV

B, T

Scan sensors output relay

RKB

T

Brake release relay contact

RR-D/U

T

Relay direction down/up

RKBB

T

Brake lining relay contact

RRE-A

T

Relay maintenance off

RKBF

T

Fire contact relay

RRUN

T

Miconic F running relay

RKE

T

Auxiliary relay to switch-on contactor

RSF

T

Crawling relay

RKF

T

Relay for speed regulator / handrail monitor

RSFK

T

Frost protection signaling relay

RSFU

T, A

Frequency converter relay

Components Copyright © 2014 INVENTIO AG

Electrical Components

Q 43831001_00

25

3 Components 3.2 Electrical Components Abbreviation

Area

RSK

B, T

RSKM RSSL

Component

Abbreviation

Area

Component

Safety circuit relay

RZRL

T

Anti-reversing solenoid time delay

B, T

Signalling safety circuit relay

RZSPF

T

Time lock trip relay

B, T

Skirting strips signaling relay

RZth

T

Time delay relay star / delta

RTH

T

Thermal trigger block

RZU

T

Return protection relay

Rth

T

Thermal motor protection relay

RZYD

T

Star / delta time delay relay

RTHFK

B, T

Antifreeze controller combplates relay

SB

T

Brake contactor

RTHK

B, T

Temperature controller combplates relay

SBL

B, T

Balustrade lighting contactor

SBM

T

Service brake / safety brake contactor

RTZS

T

Automatic lubrication timing relay

SD

T

Delta connection / direct contactor

RU1

T

Changeover relay down

SDA

T

Contactor delta connection drive unit

RU2

T

Changeover relay up

SFE

T

Travel initiation contactor

RVEKA

T

Cooling fan relay

SFU

T

Frequency converter contactor

RVFU

T, A

Frequency converter output relay

SGBA

T

Active safety brake contactor

RVN

T

Main supply output relay

SGFB

T

Regulated brake electrical relay

RVR-D/U

T

Direction output relay down/up

SH

T

Main contactor

Rz

T

Time delay relay for star / delta change over

SHE

B, T

Heating contactor

SHL

B

Handrail monitor auxiliary contactor

SIBB

B, T

RZB

T

Time delay relay for handrail monitor

RZMs

T

Time delay relay for anti-reversing solenoid

Components Copyright © 2014 INVENTIO AG

SIBS

Electrical Components

Balustrade lighting fuse Main circuit fuse by customer

Q 43831001_00

26

3 Components 3.2 Electrical Components Abbreviation

Area

SIBS1

Component

Abbreviation

Light circuit fuse by customer

Area

SKVS

B, T

Component Speed check contactor software channel

SIF

B, T

Fine fuse

SIF1

B, T

22 VAC mains fuse

SMGSP

T

Lubrication pump fuse

T

Main contactor supply

SIF4

T

Valve for lubrication mains fuse

SN

SiG

T

Fuse for rectifier

SNBA

T

SIH

T

Main fuse

Active safety brake mains supply contactor

SIHK

B, T

Radiator fuse

SR-D/U

T

Direction contactor down / up

SIHS

B, T

Heating element fuse

SRE

T

Trip inspection contactor

SIL

B, T

Light system fuse

SNBA

T

Active safety brake mains supply contactor

SILS

B, T

Light circuit fuse

SR-D/U

T

Direction contactor down / up

SIMVA

B, T

Heating fan motor fuse

SUM

B, T

Buzzer

SIMVK-A

T

Cooling fan circuit breaker

SY

T

Star connection contactor

SIS

T

Control fuse

SYA

T

Star connection drive unit contactor

SiSg

T

Fuse for signals

SZS

T

Automatic lubrication contactor

SiTr

T

Primary fuse of control transformer

TA

T

Trimming transformer control

SIS3

T

Brake release circuit breaker

THFK

B, T

SK

T

Relay check contactor

Antifreeze protection combplates thermosensor

SKVH

B, T

Speed check contactor hardware channel

THK

B, T

Combplates thermosensor

THS

B, T

High-voltage transformer

TLBB

B, T

Balustrade lighting ballast

Components Copyright © 2014 INVENTIO AG

Electrical Components

Q 43831001_00

27

3 Components 3.2 Electrical Components Abbreviation

Area

Component

Tr

B, T

TS

B, T

Transformer control

TSP

T

Transformer lubrication piston pump

VMGB

T

Safety brake booster relay

VSD

T

Delta contactor booster relay

VSR

T

Direction contactor booster relay

VSY

T

Star contactor booster relay

VSZS

T

Lubrication contactor booster relay

W

T

Resistor 2K2

WFU

T, M

Brake resistor

WTHM

T

PTC resistor in motor winding

WVB

T, M

Ballest resistor to DC brake

ZQF

T

Trip counter

ZQH

T

Hours counter

Components Copyright © 2014 INVENTIO AG

Transformer

Electrical Components

Q 43831001_00

28

4 4.1

Activities Troubleshooting – Press the emergency stop button

WARNING Open Step / Pallet Band

– Connect the maintenance operating panel

Unit with open step / pallet band could result in death or serious injury. Never leave a unit with open step / pallet band. If no immediate repair is possible, reassemble all disassembled parts in reverse order.

– Lift out the control cabinet and open it – Unit older than MIC F 2: Check every safety contact with a continuity meter and the wiring diagram – Unit with digital display: Check the display for the error message. Refer to chapter “7 Error Messages” and follow the correction instructions

 Notify the customer at arrival and at departure.  If the unit is equipped with handrail entry type "mouse trap" check all four entries are closed.  Check if the unit is equipped with a display which is visible from outside.

– Only at error message 28 or 36, refer to the chapter “Step Level Switch” – Check if the error related switch is mechanically locked

 If the display is toggling showing [d0] and an error message: – Read the error message and refer to the chapter “7 Error Messages” – Check the mentioned area for trapped objects and correct switch / sensor setting.

– Confirm the error.  Reassemble all disassembled parts in reverse order.  Restart the unit by using the key switch.

 If no display is present or the display do not show [d0]: – Set up protective barriers – Activate EoS – Unit older than MIC F 2: Remove the floor cover at the drive station – Unit with MIC F 2/3/4/5: Remove the floor covers at the tension station Activities Copyright © 2014 INVENTIO AG

Troubleshooting

Q 43831001_00

29

4 4.1

Activities Troubleshooting If the escalator does not start up when switched on, check:

– – – – – –  



The main switch is turned on Both inspection switches are set to Normal Both inspection dummy plugs are connected and secured The fuses are OK The safety circuit is closed The relays and contactors are picked up.

If there is a failure of a step band light barrier, emergency operation can be started: – – – – – –

Switch off the main switch Disconnect the defective light barrier / proximity switch (terminal 115 or 116) Insert a jumper between terminals 115 or 116 Switch on the main switch Set DIL switch S10 to OFF position The defective light barrier must be renewed as quickly as possible, and the jumper removed.

If a combplate contact has tripped, it is essential to check there are still objects in the combs or under the combplate. If the contact on the step chain tensioning device has switched off and this is not clearly due to a slight elongation of the step chain, it LED Function Miconic F 1, F 2 PCB PF1.Q is essential to establish the cause. Unit Stopped LED Status Meaning If the escalator switched off again for about 4 ... 10 seconds after LED 3 red Flashes Safety circuit open being switched on, check the speed monitoring or the handrail monitor has tripped. DIL switch not in normal position LED 2 yellow

Flashes

Interlocked shutdown

LED 2 yellow

Lit

Unit ready to start

Unit Moving

Activities Copyright © 2014 INVENTIO AG

LED Status

Meaning

LED 1 green

Flashes

Startup bypass phase

LED 1 green

Lit

Rated operation

LED 2 yellow and LED 3 red

Alternate flashing Automatic lubrication fault

Troubleshooting

Q 43831001_00

30

4 4.2

Activities Customer/Protective Barriers/EoS  A: Notify the customer of shutdown and start-up.  B: Set up protective barriers before starting any work and remove them at the end of the work.  C: Activate/deactivate EoS. - Press and hold the STOP button - Turn the key switch in up and down direction.

A [29414; 24.07.2013]

STOP

B [49102; 08.10.2013]

Activities Copyright © 2014 INVENTIO AG

C [49103; 08.10.2013]

Customer/Protective Barriers/EoS

Q 43831001_00

31

4 Activities 4.3 Floor Covers Removal and Reassembly 1

2

A

 A: Lift the end cover (3).  B: Rest the end cover (3) onto the safety shoe.  C: Remove the end cover (3) using both hands.  Remove the middle cover (2), if fitted.  D: Loosen and slide the fixing nuts (4) on both sides of the connection cover (1).  Pull the connection cover (1) horizontally and remove it.

3

B 3

1 2 3 4

Connection cover Middle cover (if present) End cover Fixing nut or wing nut (if present)

1

C

D

[35764; 11.04.2014]

Activities Copyright © 2014 INVENTIO AG

Floor Covers

Q 43831001_00

32

4 Activities 4.4 Maintenance Operating Panel Function Check DANGER Test Runs Test runs during work performed on the unit represent an increased risk to persons and components of the unit. In the course of work performed at the escalator or moving walk, trial runs should only be carried out with the maintenance operating panel. At SW, SW77 the maintenance operating panel is mounted in the top and bottom pit. 1

Maintenance operating panel

[29604; 06.04.2009]

Activities Copyright © 2014 INVENTIO AG

Maintenance Operating Panel

Q 43831001_00

33

4 Activities 4.4 Maintenance Operating Panel Function Check With the emergency stop button pressed, the unit must not start up. With MIC F 4 and higher controllers, "EoS" must be activated.  Release the lock and remove the dummy plug.  Connect and lock the maintenance operating panel (1): - Reading on the display: "r0".  Press the enable button and one of the direction buttons to run the unit in the desired direction.  Activate the emergency button.  Check that no movement is possible. 1

Maintenance operating panel

[29604; 06.04.2009]

Activities Copyright © 2014 INVENTIO AG

Maintenance Operating Panel

Q 43831001_00

34

4 Activities 4.5 Guard Plate Removal and Reassembly  Remove the control cabinet  Remove the guard plate.

[35763; 23.07.2010]

Activities Copyright © 2014 INVENTIO AG

Guard Plate

Q 43831001_00

35

4 Activities 4.6 Maintenance Steps/Pallets Removal of Steps 4

3

Only at the tension station.  Position the step (1) such that the step roller has just passed the removal recess (4).  Mark the position of the step bushings (3).  Loosen the straps (2).  Shift the straps (2) and the step bushings (3) inward.  Lift and remove the step (1).

2

Maintenance step with divided step axle Strap Step bushing Removal recess

10004335

1 2 3 4

1

[29508; 23.07.2010]

Activities Copyright © 2014 INVENTIO AG

Maintenance Steps/Pallets

Q 43831001_00

36

4 Activities 4.6 Maintenance Steps/Pallets Reassembly of Steps 4

3

Only at the tension station.       

2

Maintenance step with divided step axle Strap Step bushing Recess

10005460

1 2 3 4

Insert the step rollers into the recesses (4). Attach the step (1) to the step axle. Insert the step bushings (3). Slide on the straps (2). Check if the step (1) is centered. Tighten the strap bolts to 10 Nm. Check if the step (1) is secured without play.

1

[30297; 23.07.2010]

Activities Copyright © 2014 INVENTIO AG

Maintenance Steps/Pallets

Q 43831001_00

37

4 Activities 4.6 Maintenance Steps/Pallets Removal of Short Pallets  Remove the M5x20 screws with washers (1).  Lift the pallet (2) off, but do not turn it upside down.  Remove the pallet holder (3).

1

2

1 2 3

M5x20 screw with washer Pallet Pallet holder

3

[29510; 03.04.2009]

Activities Copyright © 2014 INVENTIO AG

Maintenance Steps/Pallets

Q 43831001_00

38

4 Activities 4.6 Maintenance Steps/Pallets Reassembly of Short Pallets NOTICE Pallet Fastening Screws 2

Pallet fastening screws can only be used once. Fasten the pallets only with new fastening screws.  Insert pallet holders (3) alternately into the inner and outer link plates.  Insert the pallets (1). All arrows must point in the same direction.  Screw in the M5x20 screws with washers (2) and tighten them to 10 Nm.

1

1 2 3

Pallets M5x20 screw with washer Pallet holder

10004338

3

[29511; 23.07.2010]

Activities Copyright © 2014 INVENTIO AG

Maintenance Steps/Pallets

Q 43831001_00

39

4 4.7

Activities Handrail Entry Function Check  Check handrail entries for trapped objects.  For “mouse trap”: Check that the three flaps are closed.  Check that the gap between the handrail entry and the handrail is uniform on all sides.

[29597; 10.10.2013]

Activities Copyright © 2014 INVENTIO AG

Handrail Entry

Q 43831001_00

40

4 4.8

Activities Combplate Combplate The unit must be put out of operation if two or more adjacent teeth are broken.  Check combplate for trapped objects.  Check that not two or more adjacent teeth of the combs are broken.

Variant 1: Function Check The contact must be triggered by moving the combplate.  Actuate only one KKP contact at a time, the triggered KKP contact must prevent the unit from starting up: - Error "10": KKP-T - Error "15": KKP-B. A B

5 mm

C

A B C

Block Roller Combplate contact KKP

[46599; 23.09.2013]

Activities Copyright © 2014 INVENTIO AG

Combplate

Q 43831001_00

41

4 4.8

Activities Combplate Variant 2: Function Check The contact must be triggered by moving the combplate.  Actuate only one KKP contact at a time. The triggered KKP contact must prevent the unit from starting up: - Error "10": KKP-TL - Error "15": KKP-BL - Error "4A": KKP-TR - Error "4b": KKP-BR.

4 mm

1

Combplate contact KKP

1

[46571; 20.11.2013]

Activities Copyright © 2014 INVENTIO AG

Combplate

Q 43831001_00

42

4 4.8

Activities Combplate Variant 3: Function Check  Actuate only one contact at a time. The triggered contact must prevent the unit from starting up: - Error "10": KKP-TL - Error "15": KKP-BL - Error "4A": KKP-TR - Error "4b": KKP-BR - Error "23": KKPYV-T - Error "29": KKPYV-B.

3

2

10 mm

9.5 mm

1

1 2 3

Combplate contact, horizontal KKP Combplate contact, vertical KKPYV (optional) Contact NYC RS-18 (optional)

[30292; 25.09.2013]

Activities Copyright © 2014 INVENTIO AG

Combplate

Q 43831001_00

43

4 4.8

Activities Combplate Variant 4: Function Check  Actuate only one contact at a time. The triggered contact must prevent the unit from starting up: - Error "10": KKP-TL - Error "15": KKP-BL - Error "4A": KKP-TR - Error "4b": KKP-BR - Error "23": KKPYV-T - Error "29": KKPYV-B. 2

1 2

Combplate contact, horizontal KKP Combplate contact, vertical KKPYV (optional)

10.2 mm

1 [46504; 09.12.2013]

Activities Copyright © 2014 INVENTIO AG

Combplate

Q 43831001_00

44

4 4.9

Activities Step Level Switch Only at error message 28 or 36.

 Check if the step level switch has triggered at bottom (error message 28) or top (error message 36).  Mark the step at the area of the triggered step level switch.  Confirm the error message on the controller.  Only if the error persists: - Switch off the main switch - Bridge out the triggered step level switch at the respective controller - Remove the feedback signal of the triggered step level switch at the respective controller - Switch on the main switch.  Move the marked step to the tension station with the maintenance operating panel.  Check three steps before and after the marked step as well as the marked step for any damage: - Step deformed / damaged - Step hook deformed / broken - Step roller defective - Step roller bearing defective - Step chain roller defective - Step axle deformed.  Change damaged steps / rollers immediately. Activities Copyright © 2014 INVENTIO AG

 Only if the triggered step level switch is bridged out: - Remove one maintenance step - Drive the step gap to the triggered step level switch - Switch off the main switch - Remove the bridge at the controller - Reconnect the feedback signal - Place the step level switch into the correct position - Switch on the main switch - Move the step band one full turn with the maintenance operating panel to verify the correct function.  Reassemble all disassembled parts in reverse order.  Restart the unit by using the key switch.

Step Level Switch

Q 43831001_00

45

5 5.1

Error Messages Relay Control Only type SWE.

Display

Error Message

Abbreviation

[00]

In operation

OK

[00]

Signaling stop relay

RSH

[01]

Signaling phase relay

RSPH

[02]

Step chain tension contact, left/ right

KKS-L/R

[03]

Check dropping contact, bottom

KKA-B

[04]

Handrail entry contact, bottom left/ KHLE-B L/R right

Error Messages Copyright © 2014 INVENTIO AG

Note

Correction

 

Check:  Step band  Contact setting  Spring tension 

Relay Control

Measure all three phases to ground Check direction of rotation of main line

Check KKA-B relay drops out

Check:  Handrail entry: – For trapped objects – For damage – For correct setting  Contact setting

Q 43831001_00

46

5 5.1

Error Messages Relay Control

Display

Error Message

Abbreviation

[05]

Combplate contact, bottom left/ right

KKP-B L/R

[06]

Signaling skirt strip relay, bottom

RSSL-B

[07]

Signaling skirt strip relay, left

RSSL-L

[08]

Main power supply

JHA

[10]

Speed check contactor

SVK

[20]

Drive chain contact, left/right

KAK-L/R

Note

Correction Check:  Combs for damage  Step for damage (before and beneath the combplate)  Combplate: – returns to its initial position – side adjusting screws are set too tightly – touches skirt panel – antilift screws are set too tightly – support plate is very dirty



Release safety brake (if installed)

Check:  Chain tension  Chain for excessive elongation  Chain damage [30]

Check dropping contact, top

Error Messages Copyright © 2014 INVENTIO AG



KKA-T

Relay Control

Check KKA-T relay drops out

Q 43831001_00

47

5 5.1

Error Messages Relay Control

Display

Error Message

Abbreviation

Note

Correction

[40]

Handrail entry contact, top left/ right

KHLE-T L/R



See [04]

[50]

Combplate contact, top left/right

KKP-T L/R



See [05]

[60]

Signaling skirt strip relay, top

RSSL-T

[70]

Signaling skirt strip relay, right

RSSL-R

[80]

Signaling PTC resistor relay

RSKL



Check motor temperature

[90]

Auxiliary brake contact

KBZ

Error Messages Copyright © 2014 INVENTIO AG

Check:  Power supply of brake motor  Brake motor for malfunction

Relay Control

Q 43831001_00

48

5 5.2 

Error Messages MICONIC F 1 To confirm interlock errors: – Switch S11 ON and OFF.

Display

Error Message

Abbreviation

Note

Correction

[-.-]

Displacement error warning

PHKE

[00]

Key switch not in operative position

JR-U JR-T

[10]

Combplate contact top

KKP-T

Check:  Combs for damage  Step for damage (before and beneath the combplate)  Combplate: – returns to its initial position – side adjusting screws are set too tightly – touches skirt panel – antilift screws are set too tightly – support plate is very dirty

[11]

Handrail entry contact top

KHLE-T

Check:  Handrail entry: – For trapped objects – For damage – For correct setting  Contact setting

Error Messages Copyright © 2014 INVENTIO AG



MICONIC F 1

Check key switch

Q 43831001_00

49

5 5.2

Error Messages MICONIC F 1

Display

Error Message

[12]

Skirting contact

[13]

HWD fault

[14]

Emergency stop

[15] [16]

Abbreviation

Note

KSL

Correction Check:  Objects trapped between step and skirting  Visible damage of steps or skirting

DH



Check stop button for damage

Complate contact bottom

KKP-B



See [10]

Handrail entry contact bottom

KHLE-B



See [11]

[17]

Step Chain tension contact

KKS-B

[20]

ROM check error

[21]

Missing step

KANK

Check:  Step / pallet band for completeness and damage  Sensors  Sensor setting  Power supply of sensor

[22]

Smoke detector

KBFM

Check:  Smoke formation  Cause of smoke  Respective component

Error Messages Copyright © 2014 INVENTIO AG

Check:  Step band  Contact setting  Spring tension Interlocked

MICONIC F 1

Q 43831001_00

50

5 5.2

Error Messages MICONIC F 1

Display

Error Message

Abbreviation

Note

Correction

[23]

Safety brake contact

KBSP

[24]

PTC resistor

WTHM

[25]

Contact dropout check

[26]

Wrong direction of rotation

PHKE

Interlocked

[27]

Deviation value exceeded

PHKE

Interlocked

[30]

Overspeed

PHKE

Interlocked

[31]

Underspeed

PHKE

Interlocked

[32]

Handrail monitor left

INHL-L

[33]

Handrail monitor right

INHL-R

[34]

Service brake contact

KB

Phase failure

RKPH

 

Measure all three phases to ground Check direction of rotation of main line

Active safety brake

KBSA



See [23]

[35] Error Messages

Copyright © 2014 INVENTIO AG

Check:  Pawl setting  Pawl for free movement  Lifting solenoid of pawl 

Check motor temperature

Check:  Motor, SKV, SRE contactors are in off position  SFE contactor picked up 

Check function and setting of PHKE, PHNK-T and PHNK-B

Check:  Sensors  Handrail speed  Try to stop handrail manually Check:  Power supply of brake motor  Brake motor for malfunction

MICONIC F 1

Q 43831001_00

51

5 5.2

Error Messages MICONIC F 1

Display [36]

Error Message

Abbreviation

Note

Correction 

Step sag check

KKA

Smoke detector

KBFM

[37]

Step missing

PHKE

Interlocked

[39]

Missing step/pallet, top

PHANK-T

Interlocked

[3A]

Light scanner error top

PHANK-T

[3B]

Missing step/pallet, bottom

PHANK-B

[3C]

Light scanner error bottom

PHANK-B

[40]

Reset

[41]

See chapter “Step Level Switch”

Check:  Smoke formation  Cause of smoke  Respective component



See [26]

Key switch top



Check key switch

[42]

Voltage drop 24 VDC



Check 24 VDC

[43]

Current limiter responded

[44]

RAM check error



Set parameter according to control cabinet sticker

[45]

SRE drop check error

    

Close inspection cover Activate EoS Open inspection cover Check function of RRE-A, SRE-A JREMACT is off

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 1

Q 43831001_00

52

5 5.2

Error Messages MICONIC F 1

Display

Error Message

Abbreviation

[46]

Step band monitor inactive

S10

[47]

Light beam error

PHKE

[88]

Undefined shutdown

Error Messages Copyright © 2014 INVENTIO AG

Note Interlocked

MICONIC F 1

Correction 

See [26]

Q 43831001_00

53

5 5.3

Error Messages MICONIC F 2 To confirm interlocked errors:

 

Switch S11 ON and OFF If the error persists: – Switch S11 to ON position – Switch the main switch off and on – Switch S11 to OFF position.

Display

Error Message

Abbreviation

[-.-]

Displacement error warning

PHKE

[00]

Key switch not in operative position

JR-U JR-D

[10]

Combplate contact, top

KKP-T KKPV-T

Error Messages Copyright © 2014 INVENTIO AG

Note

Correction

 Interlocked

MICONIC F 2

Check key switch

Check:  Combs for damage  Step for damage (before and beneath the combplate)  Combplate: – returns to its initial position – side adjusting screws are set too tightly – touches skirt panel – antilift screws are set too tightly – support plate is very dirty

Q 43831001_00

54

5 5.3

Error Messages MICONIC F 2

Display

Error Message

Abbreviation

Note

Correction

[11]

Handrail entry contact, top

KHLE-T

Check:  Handrail entry: – For trapped objects – For damage – For correct setting  Contact setting

[12]

Skirting contact, top

KSL-T

Check:  Objects trapped between step and skirting  Visible damage of steps or skirting

[13]

HWD error

HWD-relay SKVS

[14]

Emergency stop

DH

[15]

Combplate contact, bottom

KKP-B KKPV-B

[16]

Handrail entry contact, bottom

KHLE-B

[17]

Step chain tension contact

KKS-B

Check:  Step band  Contact setting  Spring tension

Upthrust contact

KUS

Check for trapped objects:  Between two adjacent steps  Between steps and skirting

[18]

Interlocked

Combplate contact horizontal, top KKPH-T

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 2



Check stop button for damage



See [10]



See [11]



See [10] Q 43831001_00

55

5 5.3

Error Messages MICONIC F 2

Display [19]

Error Message Drive chain contact

Abbreviation

Note

Correction 

KAK

Release safety brake (if installed)

Check:  Chain tension  Chain for excessive elongation  Chain damage [1A]

Smoke detector

KBFM

Check:  Smoke formation  Cause of smoke  Respective component

[1b]

Handrail displacement contact

KHLA

Check handrail:  Breakage or damage  Tension

[1C]

Combplate contact horizontal, bottom

KKPH-B

[1d]

Upthrust contact

KUS

[1E]

Combplate heating

RTHFK-T/B RSFK-T/B

[1F]

Skirting contact, bottom

[20]

ROM check error

Error Messages Copyright © 2014 INVENTIO AG



See [10]

Check for trapped objects:  Between two adjacent steps  Between steps and skirting 

Remove ice and snow from combplate

Check:  Heating element  PT100 sensor 

KSL-B

See [12]

Interlocked MICONIC F 2

Q 43831001_00

56

5 5.3

Error Messages MICONIC F 2

Display

Error Message

Abbreviation

[21]

Safety brake

KBSA KBS1A

[23]

Safety brake contact

KBSP KBS2A

[24]

PTC resistor

WTHM

[25]

Contactor release check

[26]

Rotation direction error

[27]

Displacement value exceeded

[28]

Step level contact, bottom

[2A]

Stop switch

[2b] [2d] [2F]

Note

Correction Check:  Pawl setting  Pawl for free movement  Lifting solenoid of pawl 

Check motor temperature

Check:  Motor, SKV, SRE contactors are in OFF position  SFE contactor picked up 

Check function and setting of PHKE, PHANK-B and PHANK-T

KKA-B



See chapter “Step Level Contact”

JH-T/B/ A



Release JH-T

Handrail elongation contact

KHLL



See [1b]

Defect frequency converter

GFU

 

Check error message at GFU Bypass device, if defective

Floor cover contact, top

KD-T

Error Messages Copyright © 2014 INVENTIO AG

PHKE

Interlocked

Check:  Proper fit of floor cover in frame  Contact setting

MICONIC F 2

Q 43831001_00

57

5 5.3

Error Messages MICONIC F 2

Display

Error Message

Abbreviation

[30]

Overspeed

[31]

Underspeed

[32]

Handrail monitor, left

INHL-L

[33]

Handrail monitor, right

INHL-R

[34]

Service brake contact

KB

Phase failure

RKPH

[35]

Safety brake contact

[36]

PHKE

Note Interlocked

Interlocked

Correction 

See [26]

Check:  Sensors  Handrail speed  Try to stop handrail manually Check:  Power supply of brake solenoid  Brake solenoid for malfunction  

Measure all three phases to ground Check direction of rotation of main line

KBSA KSBS1A



See [21]

Step level contact

KKA-T KKA-B



See [28]

Smoke detector

KBFM



See [1A]



See [26]

  

Check sensor Sensor setting Perform technical test [t_13]

Pallet monitor

KANK

[37]

Step absence

PHKE

Interlocked

[38]

Speed monitor

PFVK.Q INBMG

Interlocked

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 2

Q 43831001_00

58

5 5.3

Error Messages MICONIC F 2

Display

Error Message

Abbreviation

Note

[39]

Step absence, top

PHANK-T

[3A]

Initiator error, top

PHANK-T

[3b]

Step absence, bottom

PHANK-B

[3C]

Initiator error, bottom

PHANK-B

[40]

Reset

[41]

Key switch, stop



Start the unit

[42]

Voltage drop 24 VDC



Check 24 VDC

[43]

Current limit triggered

[44]

RAM check error



Set parameter according to control cabinet sticker

[45]

SRE drop check error

    

Close inspection cover Activate EoS Open inspection cover Check function of RRE-A, SRE-A JREMACT is off

[46]

Step band monitor

S10

[47]

Light barrier error

PHKE



See [26]

[4E]

Floor cover contact, bottom

KD-B



See [2F]

[88]

Undefined shutdown

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

Correction

Interlocked

Interlocked

MICONIC F 2

Check:  Step / pallet band for completeness and damage  Sensors  Sensor setting  Power supply of sensor  See [26]

Q 43831001_00

59

5 5.4

Error Messages MICONIC F 3/4/5 To confirm interlocked errors:



Press the OK button on the PCB.

Display MIC F 3/4/5E:

Display [E_01] [01] [E_02]

Display MIC F 5S:

Error Message PT: 24 VDC short circuit

Abbreviation

PB: 24 VDC short circuit

P0B

[E_03]

PA: 24 VDC short circuit

P0A

[E_04]

PT: 24 VDC short circuit

P0T

[E_05]

PB: 24 VDC short circuit

P0B

Error Messages Copyright © 2014 INVENTIO AG

Note

Correction

P0T

Interlocked

MICONIC F 3/4/5



Check +24 VDC at the corresponding PCB

Q 43831001_00

60

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_10] [10]

Combplate contact, top left

KKP-TL

MIC F 3 ≤ V3.3 US Check: version: Interlocked  Combs for damage  Step for damage (before and beneath the combplate)  Combplate: – returns to its initial position – side adjusting screws are set too tightly – touches skirt panel – antilift screws are set too tightly – support plate is very dirty

[E_11] [11]

Handrail entry contact, top left

KHLE-TL

MIC F 3 US Check: version: Interlocked  Handrail entry for trapped objects  Rubber collar for damage  Rubber collar for correct setting  Contact setting

[E_12] [12]

Skirt contact, top

KSL-T

[E_13]

Monitoring contactor, bottom

SKVB



Check that SKVB picks up

[E_14] [14]

Emergency stop

DH



Check stop button for damage

[E_15] [15]

Combplate contact, bottom left

KKP-BL



See [E_10]

Error Messages Copyright © 2014 INVENTIO AG

Check:  Objects trapped between step and skirting  Visible damage of steps or skirting

MIC F 3 ≤ V3.3 US version: Interlocked

MICONIC F 3/4/5

Q 43831001_00

61

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_16] [16]

Handrail entry contact, bottom left KHLE-BL

MIC F 3 US version: Interlocked

[E_17] [17]

Step chain tension contact

KKS-B

Interlocked

Check:  Step band  Contact setting  Spring tension

[E_18] [18]

15 % motor overspeed

INBMG INMH-R

Interlocked

Check:  Sensor  Sensor setting  All three phases of motor to ground  MIC F 3/4: Perform technical test [t_13]  MIC F 5E: Speed via [A_31], [A_32]

[E_19] [19]

Drive chain contact, top right

KAK-T KAK-TR INAK-TR

Interlocked

[E_1A]

Smoke detector, top

Error Messages Copyright © 2014 INVENTIO AG

KBFM-T

MICONIC F 3/4/5





See [E_11]

Release safety brake (if installed)

Check:  Chain tension  Chain for excessive elongation  Chain damage Check:  Smoke formation  Cause of smoke  Respective component

Q 43831001_00

62

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_1b]

Error Message

Abbreviation

Note

MIC F 3/4: Handrail displacement contact

Correction Check handrail:  Breakage or damage  Tension

KHLA

MIC F 5E: Handrail rupture, left

KHLB-L

[E_1C] [1C]

Motor underspeed

INBMG INMH-R

[E_1d]

Step upthrust contact, top

KUS-T

[1d]

Stop button, top

JH-T



Release JH-T

Combplate heating, bottom

RTHFK-B ITH-B



Remove ice and snow from combplate

[E_1E]

Interlocked



See [E_18]

Check for trapped objects:  Between two adjacent steps  Between steps and skirting

Check:  Heating element  MIC F 4/5E: PT100 sensor 

See [E_12]

[E_1F] [1F]

Skirt contact, bottom

KSL-B

[E_20]

Contact flywheel cover

KHR

[E_21]

Emergency pull switch

KHRL

 

Check cable pull for proper operation Manually release the switch

[E_22]

Stop button 1, top

JH1-T



Release JH1-T

Error Messages Copyright © 2014 INVENTIO AG

Check:  Flywheel cover is properly fastened  Contact setting

MICONIC F 3/4/5

Q 43831001_00

63

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_23]

Error Message

Abbreviation

Note

MIC F 3: Stop button 2, top

JH2-T

MIC F 4/5E: Combplate contact, vertical, top

KKPYV-T

[E_24] [24]

PTC resistor, top

WTHM-T

[E_25] [25]

Contactor dropout check

SFE

[E_26]

Rotation direction error

INVK

[E_27]

Stop button 1, bottom

JH1-B

[E_28] [28]

Step level contact, bottom

KKA-B

Error Messages Copyright © 2014 INVENTIO AG

Correction 

Release JH2-T



See [E_10]

 

Check motor temperature MIC F 3/4: With PES versions A to C, connect the PTC resistor between 1 and A2 (instead of 2)

Check:  Motor, SKV, SRE contactors are in OFF position  SFE contactor picked up Interlocked

MIC F 4/5: Interlocked

MICONIC F 3/4/5

Check:  Sensors  Sensor setting  MIC F3/4/5E: Perform technical tests [t_05], [t_06]  Power supply of sensor 

Release JH1-B



See chapter “Step Level Switch”

Q 43831001_00

64

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_29]

Error Message

Abbreviation

MIC F 3: Stop button 2, bottom

JH2-B

Note

Correction 

Release the JH2-B



See [E_10]



Release JH-T



See [E_1b]

MIC F 4/5E: Combplate contact, bottom vertical

KKPYV-B

[E_2A] [2A]

Stop button, top

JH-T

[E_2b]

MIC F 3/4: Handrail elongation contact

KHLL

MIC F 5E: Handrail rupture, right

KHLB-R

[E_2C] [2C]

Stop button, bottom

JH-B



Release JH-B

[E_2d] [2d]

Controlled drive failure

GFU GPH KSGFU

 

Check error message at GFU Bypass device, if defective

[E_2E]

Stop button, external control cabinet

JH-A



Release JH-A

[E_2F] [2F]

Floor cover contact, top

KDMR-T

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Check:  Proper fit of floor cover in frame  Contact setting Q 43831001_00

65

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction 

[E_30] [30]

15 % overspeed

INVK-T INVK-B

Interlocked

[E_31] [31]

Underspeed

INVK-T INVK-B

Interlocked

[E_32] [32]

Handrail monitor, left

INHL-L

[E_33] [33]

Handrail monitor, right

INHL-R

Check:  Sensors MIC F 3 US  Perform technical test [t_07] version: Interlocked  Handrail speed  Try to stop handrail manually

[E_34] [34]

Service brake contact

MGB-L

[E_35] [35]

Safety brake

MGBA-L

[E_36] [36]

Step level contact, top

KKA-T

[E_37]

Stop button 1, external control cabinet

JH1-A

Error Messages Copyright © 2014 INVENTIO AG

MIC F 5 V54XX: Interlocked

See [E_26]

Check:  Drive chain for damage  Main contactors pick up  All three phases of motor to ground  See [E_26]

Check:  Power supply of brake solenoid  Brake solenoid for malfunction Check:  Pawl setting  Pawl for free movement  Lifting solenoid of pawl

MIC F 4/5: Interlocked

MICONIC F 3/4/5



See [E_28]



Release JH1-A

Q 43831001_00

66

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

[E_38]

MIC F 3/4/5S:

[38]

Initiator for braking distance measurement

Abbreviation INBMG

Note Initiator defect

MIC F 5E: Drive motor initiator, right

INMH-R

[E_39] [39]

Missing step/pallet, top

INVK-T INMH-R

[E_3A] [3A]

Initiator defective, top

INVK-T

[E_3b] [3b]

Missing step/pallet, bottom

INVK-B INMH-R

[E_3C] [3C]

Initiator defective, bottom

[E_3d]

Interlocked

Correction   

Check sensor Sensor setting MIC F 3/4: Perform technical test [t_13]



See [E_18]

Check:  Step / pallet band for completeness and damage  See [E_26] 

See [E_26]



See [E_39]

INVK-B



See [E_26]

Monitoring contactor, top

SKVT



Check that SKVT picked up

[E_3E] [3E]

15 % overspeed

INVK-T INVK-B

Interlocked



See [E_26]

[E_3F] [3F]

Underspeed

INVK-T INVK-B

Interlocked



See [E_31]

[E_40] [40]

Contactor dropout check

SFE



Check if motor and brake contactors are dropped out

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 3/4/5

Q 43831001_00

67

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

[E_41] [41]

Key switch stop

[E_42]

MIC F 3: Stop button 2, external control cabinet

Abbreviation

JH2-A

MIC F 4/5E: Skirt contact, middle section, top

KSLM-T

[E_43]

Oil level, drive motor

KOMH

[E_44] [44]

Parameters lost

[E_45]

RRE-A dropout check error

RRE-A

[45]

SRE-A dropout check error

SRE-A

Inspection outlet cover open [E_46]

Handrail drive chain

Error Messages Copyright © 2014 INVENTIO AG

KHLK

Note

Correction 

Start the unit



Release the JH2-A



See [E_12]

 

Wait for 5 minutes Check oil level of gear box



Set parameter according to control cabinet sticker

    

Close inspection cover Activate EoS Open inspection cover Check function of RRE-A, SRE-A JREMACT is off

Check:  Chain tension  Chain for excessive elongation  Chain for breakage

MICONIC F 3/4/5

Q 43831001_00

68

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_47]

Error Message

Abbreviation

Note

MIC F 3/4: External shutdown



Check input for STOP-BS



Restart unit

MIC F 3 US version: Interlocked



See [E_11]

MIC F 3 ≤ V3.3 US version: Interlocked



See [E_10]

STOP_ BS

MIC F 5E: Remote stop

JREMSTOP

[E_48] [48]

Handrail entry contact, top right

KHLE-TR

[E_49] [49]

Handrail entry contact, bottom right

KHLE-BR

[E_4A] [4A]

Combplate contact, top right

KKP-TR

[E_4b] [4b]

Combplate contact, bottom right

KKP-BR

[E_4C]

Safety circuit interruption

RSK

[E_4d]

DC901

[E_4E] [4E]

Floor cover contact, bottom

[E_4F] [4F]

Shutdown

Error Messages Copyright © 2014 INVENTIO AG

Correction

Check:  PCB connector for proper fit  Voltage along safety circuit

KDMR-B

MICONIC F 3/4/5



See [E_2F]



Restart unit

Q 43831001_00

69

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_50] [50]

Handrail monitor, left

INHL-L

[E_51] [51]

Handrail monitor, right

INHL-R

[E_52]

Entrance monitoring

IRAD-T IRAD-B

Check:  Entrance monitoring (radar, light sensors, passenger guide bar light barriers)  Activate display of operating data [A_03]

[E_53]

Seismic monitor

SEIS KSEIS

Check  Relay  External evaluation

[E_54]

Pit light barrier

PHTK_B

Check  Reflector  Setting of light barrier

[E_55]

Braking resistor

WFU KTHWFU

Check:  Soiling  Short circuits to ground  Resistance value

[E_56]

Glass cladding monitor

RKGL KGL

Check  Proper seat of glass panel  Contact setting

[E_57] [57]

Engineer on Site

EoS

Error Messages Copyright © 2014 INVENTIO AG





MICONIC F 3/4/5

See [E_32]

Check if error is interlocked

Q 43831001_00

70

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_58]

Light curtain active too long

SLP1 LV1-PE LV2-PE

Check:  Display of light curtain controller for defective light barriers  Step band in the displayed light curtain area for cause of error  Replace defective light barrier

[E_62] [62]

Crawling speed too slow

GFU GFU-C INBMG

Check:  Mechanical movement of unit  Power of unit without load  Parameter of GFU, GFU-C  Function of GFU, GFU-C, INBMG

[E_63]

Water level monitor, top

KWS-T



Check drive station pit for water

DH-B



Check stop button

[E_64]

Emergency stop, bottom

[E_65]

Start command pending

[E_66]

Remote stop via communication

[E_67]

PA: System status

[E_68]

PB-PA: System check

[E_69]

PA-PT: System check

[E_6A]

PA-PB: System check

[E_6b]

PT-PA: System check

Error Messages Copyright © 2014 INVENTIO AG

Check:  Key switches or start button for damage  Connection to BMS

MICONIC F 3/4/5



Check connection to BMS



Check parameter setting

Q 43831001_00

71

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_6C] [6C]

SB dropout check

I-SB



Check function of SB

[E_6d] [6d]

SR-U dropout check

I-SR-U



Check function of SR-U, SR1-U

[E_6E] [6E]

SR-D dropout check

I-SR-D



Check function of SR-D, SR1-D

[E_6F] [6F]

Dropout check motor contactors

I-SANTR



Check function of SY, SD, SFU, SN

[E_70]

SGBF dropout check

I-SGBF



Check function of SGBF

[E_71]

SR1-U dropout check

I-SR1-U



Check function of SR-U, SR1-U



Check function of SR-D, SR1-D



See [E_34]



Restart unit



See [E_19]

[E_72]

SR1-D dropout check

I-SR1-D

[E_73] [73]

Service brake dropout check

MGB MGB-L

[E_74]

Drive shut down

MIC F 5 V54XX: Interlocked

[E_75]

Drive chain contact, top left

INAK-TL KAK-TL

[E_76]

Overheat monitoring of truss

PB board X6.1

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 3/4/5

Check:  LHDC cable for short circuit  24 VDC  2 ... 6.4 VDC at PB X6.1

Q 43831001_00

72

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_77]

[E_78]

Error Message

Abbreviation

Note

Evacuation

End of evacuation

Correction Check:  Safety relay  Inputs

I-EVAK1 I-EVAK2 Interlocked

Check:  Reason for evacuation travel  Error history 

[E_79]

Fuse 110 VAC

SIS2

Check 110 VAC control voltage

[E_7A]

Fuse main motor

SIHM

[E_7b]

Stop button, customer provided

DH-BS2



Check customer provided stop button



See [E_34]

Check:  Main motor fuses  Equal load conditions at double drive

[E_7C] [7C]

Service brake dropout check

MGB-L

[E_7d] [7d]

SB dropout check

I-SB



Check SB

[E_7E] [7E]

SR-U dropout check

I-SR-U



Check SR-U, SR1-U

[E_7F] [7F]

SR-D dropout check

I-SR-D



Check SR-D, SR1-D

[E_80] [80]

Dropout check of motor contactors I-SANTR



Check SY, SD, SFU, SN

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 3/4/5

Q 43831001_00

73

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_81] [81]

Error Message

Abbreviation

Note

Correction

SB pickup check

I-SB



Check SB picks up during travel

SR-U pickup check

I-SR-U



Check SR-U, SR1-U pick up during travel

SR-D pickup check

I-SR-D



Check SR-D, SR1-D pick up during travel

Pickup check of motor contactors

I-SANTR



Check SY, SD, SFU, SN pick up during travel

[E_89] [89]

RB contactor dropout check

RB



Check RB relay drops out

[E_8A] [8A]

Motor underspeed

INMH-R



See [E_18]

[E_82] [82] [E_83] [83] [E_84] [84] [E_85] [85] [E_86] [86] [E_87] [87] [E_88] [88]

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 3/4/5

Q 43831001_00

74

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

[E_8b] [8b]

15 % motor overspeed

INMH-R

Interlocked



See [E_18]

[E_8C] [8C]

30 % motor overspeed

INMH-R

Interlocked



See [E_18]

[E_8d] [8d]

Floor cover contact, top

KDMR-T

[E_8E] [8E]

Floor cover contact, bottom

KDMR-B



See [E_2F]

[E_8F] [8F]

Step level contact, top

KKA-T

[E_90] [90]

Step level contact, bottom

KKA-B



See [E_28]

[E_91] [91]

Stop button, bottom

JH-B



Release JH-B

[E_92] [92]

Service brake pickup check

MGB



See [E_34]

[E_94] [94]

Stop button, top

JH-T



Release JH-T

[E_9d]

Emergency stop

DH-M



Check DH-M

I-SBC-ERR



Check service brake control unit for error message

[E_9E]

Service brake control error

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

Interlocked

MICONIC F 3/4/5

Q 43831001_00

75

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

[E_9F]

Revision control error

[E_A0] [A0]

PEM/PB: Reset

[E_A1] [A1]

PES/PT: Reset

[E_A2]

PES1/PA: Reset

[E_A3]

PES2/P2: Reset

[E_A4]

PES3/P3: Reset

[E_A5]

MIC F 3/4:

Abbreviation

Note

I-REC-ERR

Correction 

Check revision control unit for error message



Check 24 VDC at P01



Remove blocking device

 

Check parameter setting Replace PEM



See [E_17]

ALCD 80: Reset MIC F 5E: Blocking device, left [E_A6]

KBV-L

MIC F 3/4: PEM: Bus retry reset MIC F 5E: Step chain tension contact, bottom KKS-BL left

[A6]

Interlocked

PB: Bus retry reset

Error Messages Copyright © 2014 INVENTIO AG

Check:  Bus connection  Jumper setting MICONIC F 3/4/5

Q 43831001_00

76

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_A7]

Error Message

Abbreviation

Correction  

MIC F 3/4: PES: Bus retry reset MIC F 5E: Step chain link contact, left

Note

Check parameter setting Replace PES

Check:  Step chain  Lubrication of step chain

KKL-L

[A7]

PB: Bus retry reset



See [A6]

[E_A8]

MIC F 3/4:

 

Check parameter setting Replace PES1



See [E_A7]

 

Check parameter setting Replace PES2



Check P0049

PES1: Bus retry reset MIC F 5E: Step chain link contact, right [E_A9]

KKL-R

MIC F 3/4: PES2: Bus retry reset MIC F 5E: Communication error

RS232/ RS485-2

[E_AA]

PES3: Bus retry reset

 

Check parameter setting Replace PES3

[E_Ab]

ALCD 80: Bus retry reset

 

Check parameter setting Replace ALCD 80

[E_AC]

Buffer full reset

 

Check parameter setting Replace PEM

[AC]

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

77

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

Correction

Buffer full reset

 

Check parameter setting Replace PES

[E_AE]

Buffer full reset

 

Check parameter setting Replace PES1

[E_AF]

Buffer full reset

 

Check parameter setting Replace PES2

[E_b0]

MIC F 3/4:



See [E_AA]



Check next error entry and correct



See [E_Ab]



Check next error entry and correct



See [E_AC]



Check next error entry and correct



Update software

[E_Ad] [Ad]

Buffer full reset MIC F 5E: Reset [E_b1]

MIC F 3/4: Buffer full reset MIC F 5E: Reset

[E_b2]

MIC F 3/4: Wrong message reset MIC F 5E: Reset

[b2]

Wrong message reset

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

78

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_b3]

Error Message

Abbreviation

MIC F 3/4: Wrong message reset MIC F 5E: Reset

[b3]

Wrong message reset

[E_b4]

MIC F 3/4: Wrong message reset MIC F 5E: Reset

Note

Correction 

See [E_Ad]



Check next error entry and correct



Update software



See [E_AE]



Check next error entry and correct

[E_b5]

Wrong message reset



See [E_AF]

[E_b6]

Wrong message reset



See [E_AA]

[E_b7]

Wrong message reset



See [E_Ab]

[E_b8]

MIC F 3/4:



See [E_AC]



Check connecting line



See [E_A0]

Reset MIC F 5E: Bus retry reset [b8]

Reset

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

79

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_b9]

Error Message

Abbreviation

MIC F 3/4: Reset MIC F 5E: Buffer full reset

Note

Correction  

Check parameter setting Replace PES, PEM



Check of quickly activated inputs

[b9]

Reset



See [E_A0]

[E_bA]

MIC F 3/4:

 

Check parameter setting Replace PES1, PEM

Reset MIC F 5E:

Check:  Connecting line  Incorrect devices connected

Wrong message reset [E_bb]

MIC F 3/4: Reset MIC F 5E: Timeout reset

[E_bC]

MIC F 3/4: Reset MIC F 5E: Flash reset

[E_bd]

Reset

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

 

Check parameter setting Replace PES2, PEM



Check connecting line

 

Check parameter setting Replace PES3, PEM

 

Set parameter to default Program parameter according to control cabinet sticker

 

Check parameter setting Replace ALCD 80, PEM Q 43831001_00

80

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_bE] [bE] [E_bF]

Error Message

Abbreviation

Timeout reset Timeout reset

Note

Correction 

See [E_AC]



Check jumper setting



See [E_Ad]



Check jumper setting

[E_C0]

Timeout reset



See [E_A8]

[E_C1]

Timeout reset



See [E_A9]

[E_C2]

Timeout reset



See [E_AA]

[E_C3]

Timeout reset



See [E_Ab]

Reset



Press the reset button on the PEM/PB

Reset



Press the reset button on the PES/PT

[E_C6]

Reset



Press the reset button on the PES1

[E_C7]

Reset



Press the reset button on the PES2

[E_C8]

Reset



Press the reset button on the PES3

[E_C9]

Reset



Turn supply voltage at the ALCD 80 off and on



Press the reset button on the PEM, PES



Press the reset button on the PB, PT

[bF]

[E_C4] [C4] [E_C5] [C5]

[E_CA] [CA]

Board reset

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

81

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

Note

[E_Cb] [Cb]

Voltage reset

[E_CC]

MIC F 3:

[CC]

Combplate contact 2, bottom left

KKP-BL

MIC F 3 ≥ V3.3: Interlocked

MIC F 4/5:

INBMG INMH INMH-R

Interlocked

30 % motor overspeed [E_Cd]

Check:  22 VAC supply  24 VDC at P01

MIC F 3: Power failure > 250 ms with UPS

USV

Combplate contact 2, bottom right KKP-BR

MIC F 3 ≥ V3.3: Interlocked

MIC F 4: Power failure > 250 ms with UPS [E_CE]

MIC F 3:

[CE]

Combplate contact 2, top left

USV KKP-TL

MIC F 3 ≥ V3.3: Interlocked

INVK-T INVK-B

Interlocked

MIC F 4/5: 30 % overspeed

Error Messages Copyright © 2014 INVENTIO AG

Correction

MICONIC F 3/4/5



See [E_10]

 

Release the safety brake (if installed) See [E_18]



Check line voltage supply



See [E_10]



Check line voltage supply



See [E_10]

 

Release safety brake (if installed) See [E_26]

Q 43831001_00

82

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

[E_CF]

MIC F 3:

[CF]

Combplate contact 2, top right

Abbreviation

Note MIC F 3 ≥ V3.3:

Correction 

See [E_10]

 

Release safety brake (if installed) See [E_26]

KBFM-B



See [E_1A]

Skirt contact, middle

KSL-M



See [E_12]

[E_d3] [d3]

Phase failure

RKPH

 

Measure all three phases to ground Check direction of rotation of main line

[E_d4]

Rubber belt contact, top

KGB-T

[E_d5]

Rubber belt contact, bottom

KGB-B



Check rubber belt

[E_d6]

Blocking device

KBV



Check blocking device

[E_d7]

Combplate heating, top

RTHFK-T ITH-T



See [E_1E]

[E_d8] [d8]

Step upthrust contact, bottom

KUS-B



See [E_1d]

[E_d9]

Brake lining monitor

INBB

 

Check brake lining Replace brake lining if minimum is reached

[E_dA] [dA]

Stop button, customer provided

RHBS DH-BS



Check RHBS, DH-BS

KKP-TR

Interlocked

30 % overspeed

INVK-T INVK-B

Interlocked

[E_d1]

Smoke detector, bottom

[E_d2]

MIC F 4/5:

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

83

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

[E_db]

Water level monitor, bottom

KWS KWS-B

[E_dC]

Contactor pickup check

SK

[E_dE]

PTC resistor, bottom

WTHM-B

[E_dF]

Shutdown with lubrication failure

KDZS KDS

[E_E0]

Unit-specific error, bottom

KSPEZ-B

[E_E1]

Unit-specific error, top

KSPEZ-T

[E_E2]

Unit-specific error

KSPEZ-1

[E_E3]

Unit-specific error

KSPEZ-2

[E_E4]

MIC F 3:

Note

MIC F 3 ≥ V3.2 US version: Interlocked

MIC F 4/5E: MIC F 3:



Check wiring of the SKU, SKD, SRE contactors



Check motor temperature



Unit-specific



See [E_E0]



Unit-specific error MIC F 4/5E:

See [E_E0]

Drive station too warm  Cool drive station

Over temperature Error Messages

Check tension station pit for water

Tension station too warm  Cool tension station

Over temperature

Copyright © 2014 INVENTIO AG



Check lubrication system:  Level switch  Manometric switch  Tubes for kinks

Unit-specific error

[E_E5]

Correction

MICONIC F 3/4/5

Q 43831001_00

84

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_E6]

Error Message

Abbreviation

Note

MIC F 3:



Unit-specific error MIC F 4/5E: MIC F 3:

[E7]

Unit-specific error MIC F 4/5E: Missing step/pallet, bottom

[E_E8]

See [E_E0]

Machine room too warm  Cool machine room

Over temperature [E_E7]

Correction

INVK-B

Interlocked



See [E_E0]



See [E_39]



See [E_E0]

MIC F 3: Brake monitor, channel 1

SKUE1

MIC F 4: Unit-specific error MIC F 5E:

Check:  GFU parameters  GFU activation

Controlled brake monitor

Error Messages Copyright © 2014 INVENTIO AG

MICONIC F 3/4/5

Q 43831001_00

85

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_E9]

Error Message

Abbreviation

Note

Correction

MIC F 3: Brake monitor, channel 2

SKUE2

MIC F 4:



See [E_E0]



See [E_E8]



See [E_38]



Start the next unit in line



See [E_E0]



See [E_26]

Unit-specific error MIC F 5E: Controlled brake 2 monitor [E_EA]

MIC F 3:

[EA]

Braking distance exceeded MIC F 4/5:

INBMG

Braking distance exceeded

INMH-R

[E_Eb]

Consecutive operation

[E_EC]

MIC F 3:

[EC]

Unit-specific error

MIC F 5: Interlocked

MIC F 4/5: Initiator defective, top

Error Messages Copyright © 2014 INVENTIO AG

INVK-T

MICONIC F 3/4/5

Q 43831001_00

86

5 5.4

Error Messages MICONIC F 3/4/5

Display [E_Ed]

Error Message

Abbreviation

Note

Correction

MIC F 3/4: Unit-specific error MIC F 5E: Emergency stop 2

[E_EE] [E_EF]

DH



See [E_E0]



Press DRES2 or DRES3 to show the error



See [E_39]



See [E_26]

Unit-specific error

[E_Er]

Electronically interlocked error

[E_F0] [F0]

Missing step/pallet, top

INVK-T

[E_F1] [F1]

Initiator defective, bottom

INVK-B

[E_F2] [F2]

PES/PT: System check

MIC F 5E: Interlocked



See [E_A7]

[E_F3] [F3]

PEM/PB: System check

MIC F 5E: Interlocked



See [E_A6]

[E_F4] [F4]

PES/PT-PB: System check



See [E_A7]

[E_F5] [F5]

PEM/PB-PT: System check



See [E_A6]

Error Messages Copyright © 2014 INVENTIO AG

Interlocked

MICONIC F 3/4/5

Q 43831001_00

87

5 5.4

Error Messages MICONIC F 3/4/5

Display

Error Message

Abbreviation

[E_F6] [F6]

RB contactor dropout check

RB

[E_F7] [F7]

RGBA contactor dropout check

RGBA

Error Messages Copyright © 2014 INVENTIO AG

Note

MIC F 5: Interlocked

MICONIC F 3/4/5

Correction 

Check RB



Check RGBA, RGBA1

Q 43831001_00

88