Telnet Command 74eoc

Telnet Command for 74EOC

Note: 1.This document is a temporary test version for your reference, the final one will be provided before the shipment of the goods. 2.You need to input the actual value for the italic part.. Account:root Password: public 3.. Software version required V 2.6.2 or above.

1. System Part 1)

Query basic information of the system 【Command Format】esys get basicinfo 【Parameter Declaration】 【Example】esys get basicinfo

2)

Query system MAC address 【Command Format】esys get mac 【Parameter Declaration】 【Example】esys get mac

3)

Query system IP address 【Command Format】esys get ip 【Parameter Declaration】 【Example】esys get ip

4)

Query system sub net mask 【Command Format】esys get subnetmask 【Parameter Declaration】 【Example】esys get subnetmask

5)

Query system default gate way 【Command Format】esys get defaultgw 【Parameter Declaration】 【Example】esys get defaultgw

6)

Query system hardware version 【Command Format】esys get hwversion 【Parameter Declaration】 【Example】esys get hwversion

7)

Query system software version 【Command Format】esys get swversion 【Parameter Declaration】 【Example】esys get swversion

8)

Query system bootloader version 【Command Format】esys get bootloaderver 【Parameter Declaration】 【Example】esys get bootloaderver

9)

Query system kernel version 【Command Format】esys get kernel 【Parameter Declaration】 【Example】esys get kernel

10) Query manufacturer information 【Command Format】esys get manufacturer 【Parameter Declaration】 【Example】esys get manufacturer

11) Query product product’ss serial number 【Command Format】esys get serialnum 【Parameter Declaration】 【Example】esys get serialnum

12) Query system TFTP server address 【Command Format】esys get tftpsrv 【Parameter Declaration】 【Example】esys get tftpsrv

13) Query system online time 【Command Format】esys get onlinetime 【Parameter Declaration】 【Example】esys get onlinetime

14) Query system release time 【Command Format】esys get releasetime 【Parameter Declaration】 【Example】esys get releasetime

15) Query SNMP configuration information 【Command Format】esys get snmp 【Parameter Declaration】 【Example】esys get snmp

16) Query system broadcast storm control information 【Command Format】esys get stormctrl all/port 【Parameter Declaration】(port: cable1/calble2/eht3/eth4/eth5) 【Example】Query all ports：esys get stormctrl all Query eth3：esys get stormctrl eth3

17) Set system network configurations 【Command Format】esys set netcfg ip mask gateway 【Parameter Declaration】 【Example】esys set netcfg 192.168.1.254 255.255.255.0 0.0.0.0

18) Set system IP address 【Command Format】esys set ip value 【Parameter Declaration】 【Example】esys set ip 192.168.1.254

19) Set system sub net mask 【Command Format】esys set subnetmask value 【Parameter Declaration】 【Example】esys set subnetmask 255.255.255.0

20) Set system default gate way 【Command Format】esys set defaultgw value 【Parameter Declaration】 【Example】esys set defaultgw 0.0.0.0

21) Set manufacturer information 【Command Format】esys set manufacturer value 【Parameter Declaration】 【Example】esys set manufacturer 湖南华宽通科技股份有限公司

22) Set product serial number 【Command Format】esys et serialnum value 【Parameter Declaration】 【Example】esys get serialnum HKTFM-010025

23) Set TFTP server address 【Command Format】esys set tftpsrv value 【Parameter Declaration】 【Example】esys set tftpsrv 192.168.1.250

24) Set system broadcast storm control percentage 【Command Format】esys set stormctrl percentage value 【Parameter Declaration】value (0..100:enable, 255:disable) 【Example】Control function on at 50%：esys set stormctrl percentage 50 Control function off：esys set stormctrl percentage 255

25) Set parameters for system broadcast storm control port 【Command Format】esys set stormctrl port broadcastenable othercastenable 【Parameter Declaration】port: cable1/calble2/eht3/eth4/eth5) 【Example】Start control port：esys set stormctrl cable2 1 1

26) Set SNMP function 【Command Format】esys set snmp enable/disable 【Parameter Declaration】 【Example】Start：esys set snmp enable

27) Set name and other parameters for SNMP 【Command Format】esys set snmp name/location/contanct value 【Parameter Declaration】 【Example】esys set snmp name HKTeoc esys set snmp location OMC

28) Set SNMP comminute name/value 【Command Format】esys set snmp rw-community/ro-community value 【Parameter Declaration】 【Example】esys set snmp ro-community public esys set snmp rw-community private

29) Set SNMP trap server address 【Command Format】esys set snmp trapsrv value 【Parameter Declaration】 【Example】esys set snmp trapsrv 192.168.1.101

30) VLAN Query management VLAN 【Command Format】esys get management_vlan 【Parameter Declaration】 【Example】esys get management_vlan

31) VLAN Set management VLAN 【Command Format】esys set management_vlan enable/disable vid 【Parameter Declaration】 【Example】esys set management_vlan disable esys set management_vlan enable 99

2. Master part 1)

Query all the devices devices’ connection under the same master, include master and slave, and slaves slaves’ information, like user name. 【Command Format】emst get topu all

【Parameter Declaration】 【Example】emst get topu all

2)

Query all the devices devices’ connection under the same master, only list the mac address and ID number. 【Command Format】emst get topu mac 【Parameter Declaration】 【Example】emst get topu mac

3)

Query all master modules modules’ basic information 【Command Format】emst get basicinfo all 【Parameter Declaration】 【Example】emst get basicinfo all

4)

Query designated master module module’ss basic information 【Command Format】emst get basicinfo mid 【Parameter Declaration】mid为master的id号。1# master的id为1，2# master的id为2。 【Example】emst get basicinfo 1

5)

Query master module module’ss mac address 【Command Format】emst get mid mac 【Parameter Declaration】 【Example】emst get 1 mac

6)

Query master module type 【Command Format】emst get mid type 【Parameter Declaration】 【Example】emst get 2 type

7)

Query master module module’ss software version 【Command Format】emst get mid fwversion 【Parameter Declaration】 【Example】emst get 1 fwversion

8)

Query master module's hardware version 【Command Format】emst get mid hwversion 【Parameter Declaration】 【Example】emst get 1 hwversion

9)

Query master module's manufacturer information 【Command Format】emst get mid manufacturer 【Parameter Declaration】 【Example】emst get 1 manufacturer

10)

Query master module's PIB file version information 【Command Format】emst get mid pibversion

【Parameter Declaration】 【Example】emst get 1 pibversion

11) Query master module' snmk key 【Command Format】emst get mid nmk 【Parameter Declaration】 【Example】emst get 1 nmk

12)

Query master module's SNID 【Command Format】emst get mid snid 【Parameter Declaration】 【Example】emst get 1 snid

13)

Query all the isolated slaves 【Command Format】emst get accctrl 【Parameter Declaration】 【Example】emst get accctrl

14) Set master module's SNID 【Command Format】emst set mid snid value 【Parameter Declaration】 【Example】emst set 1 snid 1

15) Isolated the designated slave 【Command Format】emst add accctrl mac 【Parameter Declaration】 【Example】emst add accctrl 01:02:03:04:05:06

16) Cancel the slave slave’ss isolation status 【Command Format】emst del accctrl mac 【Parameter Declaration】 【Example】emst del accctrl 01:02:03:04:05:06

17) Cancel all the slaves slaves’ isolation status 【Command Format】emst del accctrl all 【Parameter Declaration】 【Example】emst del accctrl all

18)

Upgrade master module 【Command Format】emst upgrade mid 【Parameter Declaration】Start TFTP server before updated，and put the file to be updated into TFTP software’s specified folder, the software file to be upgraded must be named as master_74.nvm and master_74.pib。 【Example】emst upgrade 1

et factory settings for master module 19) Res Reset 【Command Format】emst restore mid

【Parameter Declaration】 【Example】emst restore 1

20) Query dynamic VLAN configurations 【Command Format】emst get dynvlan 【Parameter Declaration】 【Example】emst get dynvlan

21) Set dynamic VLAN configurations 【Command Format】emst set dynvlan enable/disable/scope mid port started endid 【Parameter Declaration】 【Example】 emst set dynvlan scope 1 0 1 1024 emst set dynvlan scope 1 1 1 1024 emst set dynvlan scope 1 2 1 1024 emst set dynvlan scope 1 3 1 1024 emst set dynvlan enable Firstly, Set all ports’ VID scope, and then execute emst set dynvlan enable.

22)

Set Master output level 【Command Format】emst set <master id> powerlevel 【Parameter Declaration】<master id>:Set the module’s id as 1,2; : Set the range of master output level as【75,104】 【Example】 Set the output level of EOC Module 1to 90dBuV emst set 1 powerlevel 90

23)

Query master output level 【Command Format】emst get <master id> powerlevel 【Parameter Declaration】<master id>Set the module’s id as 1,2; 【Example】 Query the output level of EOC Module 1 emst get 1 powerlevel

24)

Restart Master 【Command Format】emst reset <master id> 【Parameter Declaration】<master id>:Set the module’s id as 1,2; 【Example】 Restart Module 1： emst reset 1

3. Slave Part 1)

Query all slaves slaves’ basic information 【Command Format】eslv get basicinfo all

【Parameter Declaration】 【Example】eslv get basicinfo all

2)

Query the designated slave slave’ss basic information 【Command Format】eslv get basicinfo sid 【Parameter Declaration】 【Example】eslv get basicinfo 101

3)

Query the designated slave slave’ss mac 【Command Format】eslv get sid mac 【Parameter Declaration】sid is slave’s id #. E.g., Sid=101 stands for the #1 slave #1 master, sid=215 stands for #15 slave under #2 master. 【Example】eslv get 132 mac

4)

Query slave type 【Command Format】eslv get sid type 【Parameter Declaration】 【Example】eslv get 202 type

5)

Query slave slave’ss software version 【Command Format】eslv get sid fwversion 【Parameter Declaration】 【Example】eslv get 120 fwversion

6)

Query slave slave’ss hardware version 【Command Format】eslv get sid hwversion 【Parameter Declaration】 【Example】eslv get 101 hwversion

1)

Query slave slave’ss manufacturer information 【Command Format】eslv get sid manufacturer 【Parameter Declaration】 【Example】eslv get 101 manufacturer

2)

Query slav slavee’s pib version 【Command Format】eslv get sid pibversion 【Parameter Declaration】 【Example】eslv get 101 pibversion

3)

Query slave slave’ss Nmk key 【Command Format】eslv get sid nmk 【Parameter Declaration】 【Example】eslv get 101 nmk

4)

Query slave slave’ss current status 【Command Format】eslv get sid status 【Parameter Declaration】

【Example】eslv get 101 status

5)

Query slave slave’ss user name 【Command Format】eslv get sid username 【Parameter Declaration】 【Example】eslv get 101 username

6)

Query slave slave’ss user address 【Command Format】eslv get sid useraddr 【Parameter Declaration】 【Example】eslv get 101 useraddr

7)

Query slave slave’ss user phone number 【Command Format】eslv get sid userphone 【Parameter Declaration】 【Example】eslv get 101 userphone

8)

Query slave slave’ss IP address 【Command Format】eslv get sid devip 【Parameter Declaration】 【Example】eslv get 101 devip

9)

Query slave slave’ss link speed limit information 【Command Format】eslv get sid speedlimit 【Parameter Declaration】 【Example】eslv get 101 speedlimit

10) Query slave slave’ss other link information 【Command Format】eslv get sid linkinfo 【Parameter Declaration】 【Example】eslv get 101 linkinfo Note: Only if there is data throughput, then you can query the statistics

11) Query slave slave’ss port broadcast storm control information 【Command Format】eslv get sid stormctrl 【Parameter Declaration】 【Example】eslv get 101 stormctrl

12) Query slave slave’ss vlan information 【Command Format】eslv get sid vlan 【Parameter Declaration】 【Example】eslv get 101 vlan

13)

Query slav slav’ user template information 【Command Format】eslv get usertemplet 【Parameter Declaration】 【Example】eslv get usertemplet

14) Set slave slave’ss port speed limit 【Command Format】eslv set sid speedlimit port upspeed downspeed 【Parameter Declaration】Value's unit is kbps, value range is 0,64,128...16384,is the multiple of 64. 0 means close the speed limit. 【Example】eslv set 101 speedlimit 0 512 512

15)

Set slave slave’ss broadcast storm control enable 【Command Format】eslv set sid stormctrl broadcast_enable multicast_enable

unkownDA_enable pps 【Parameter Declaration】 【Example】eslv set 101 stormctrl 1 1 1 640

16)

Set slave slave’ss port capability set 【Command Format】eslv set sid

portability port auto_negotiation speed duplex

【Parameter Declaration】

auto_negotiation: enable, disable speed:100,10 duplex: full ,half 【Example】eslv set 101 portability 0 enable 100 full

17)

Set slave slave’ss vlan function status 【Command Format】eslv set sid vlan enable/disable 【Parameter Declaration】 【Example】eslv set 101 vlan enable

18)

Set slave slave’ PVID 【Command Format】eslv set sid vlan port vid 【Parameter Declaration】vid=0, cancel the VLAN setting of port 【Example】before modify the PVID of Slave need operate "vlan enble" command open VLAN function. eslv set 101 vlan enable eslv set 101 vlan 0 1024 eslv set 101 vlan 1 1024 eslv set 101 vlan 2 1024 eslv set 101 vlan 3 1024

19)

Set slave slave’ss user template 【Command Format】eslv set usertemplet name/addr/phone/devip value 【Parameter Declaration】 【Example】eslv set usertemplet name/addr/phone/devip value

20)

Open account for user 【Command Format】eslv adduser mid mac name addr phone [devip] 【Parameter Declaration】 【Example】eslv adduser 1 01:02:03:04:05:06 ** road 192.168.1.103

21)

Modify user user’ss information 【Command Format】eslv moduser sid name/addr/phone/devip value 【Parameter Declaration】 【Example】eslv moduser 101 name **

22) Close the user user’ss account 【Command Format】eslv deluser sid 【Parameter Declaration】 【Example】eslv deluser 101

23) Upgrade slave 【Command Format】eslv upgrade sid 【Parameter Declaration】 Before upgrade, you need to switch on TFTP server, and put the target upgrade file into the designated directory of the TFTP software. And the file of the software should be named as slave_74.nvm and slave_74.pib(7411 slave), or slave_64.nvm and slave_64.pib(6400 slave). 【Example】eslv upgrade 101

24) Restart Slave 【Command Format】eslv reset <slave id> 【Parameter Declaration】<slave id>：slave id，command “emst get topu all” to get slave id 【Example】restart the slave id 101： eslv reset 101

4. Eqos 1)

Query master/slave master/slave’ss all qos information 【Command Format】eqos get mid /sid all 【Parameter Declaration】 mid is master’s id number. #1 master’s id is 1, #2 master’s id is 2. Sid is for slave device’s id number. eg. Sid=101 means the #1 slave under #1 master, sid=215 means the #15 slave under #2 master, etc. 【Example】Query master：eqos get 1 all Query slave：eqos get 101 all

2)

default Priority Query master/slave's qos information information——default 【Command Format】eqos get mid /sid capdefault 【Parameter Declaration】 【Example】eqos get 1 capdefault

3)

cos(vlan) Priority. Query master/slave's qos information information——cos(vlan) 【Command Format】eqos get mid /sid cospri 【Parameter Declaration】 【Example】eqos get 1 cospri

4)

tos Priority. Query master/slave's qos information information——tos 【Command Format】eqos get mid /sid tospri 【Parameter Declaration】 【Example】eqos get 1 tospri

5)

dscp Priority Query master/slave's qos information information——dscp 【Command Format】eqos get mid /sid dscppri 【Parameter Declaration】 【Example】eqos get 1 dscppri

6)

TTL Query master/slave's qos information information——TTL 【Command Format】eqos get mid /sid prittl 【Parameter Declaration】 【Example】eqos get 1 prittl

7)

cap buffer Query master/slave's qos information information——cap 【Command Format】eqos get mid /sid capbuf 【Parameter Declaration】 【Example】eqos get 1 capbuf

8)

default Priority. Set master/slave's qos information information——default 【Command Format】eqos set mid /sid capdefault igmpcast/unicast/avstream/multicast cap0/cap1/cap2/cap3 【Parameter Declaration】 【Example】eqos set 1 capdefault igmpcast cap0 eqos set 1 capdefault unicast cap2

9)

cos Priority enable/disable Set master/slave's qos information information——cos 【Command Format】eqos set mid /sid cospri enable/disable 【Parameter Declaration】 【Example】eqos set 1 cospri enable

cos Priority. 10) Set master/slave's qos information information——cos 【Command Format】eqos set mid /sid cospri 0..7 cap0/cap1/cap2/cap3 【Parameter Declaration】 【Example】eqos set 1 cospri 0 cap1 eqos set 1 cospri 5 cap2

tos Priority enable/disable 11) Set master/slave's qos information information——tos 【Command Format】eqos set mid /sid tospri enable/disable 【Parameter Declaration】 【Example】eqos set 1 tospri disable

cos Priority enable/disable 12) Set master/slave's qos information information——cos 【Command Format】eqos set mid /sid tospri 0..7 cap0/cap1/cap2/cap3 【Parameter Declaration】

【Example】eqos set 1 tospri 2 cap1 eqos set 1 tospri 7 cap2

13) Set master/slave's qos information cos Priority enable/disable information——cos 【Command Format】eqos set mid /sid dscppri enable/disable 【Parameter Declaration】 【Example】eqos set 1 dscppri disable

cos Priority enable/disable 14) Set master/slave's qos information information——cos 【Command Format】eqos set mid /sid dscppri 【Parameter Declaration】 【Example】eqos set 1 dscppri 2 cap1 eqos set 1 dscppri 7 cap2

each Priority's ttl 15) Set master/slave's qos information information——each 【Command Format】eqos set mid /sid prittl cap0/cap1/cap2/cap3 10..65000 【Parameter Declaration】 【Example】eqos set 1 prittl cap0 3000

Buffer queue enable/disable 16) Set master/slave's qos information information——Buffer 【Command Format】eqos set mid /sid capbuf enable/disable 【Parameter Declaration】 【Example】eqos set 1 capbuf enable

Buffer queue percentage 17) Set master/slave's qos information information——Buffer 【Command Format】eqos set mid /sid capbuf percent1 percent2 percent3 percent4 【Parameter Declaration】percent1 percent2 percent3 percent4之和必须等于100. 【Example】eqos set 1 capbuf 10 20 40 30