Loading documents preview...
A
7”
A
DETAIL A
16”
Slide bolt locks bed from rolling out
22 1⁄8” 3 3⁄8”
4”
4”
17”
15 ¾”
A
81 ½”
43”
SECTION A-A
1”
1 of 4 ®
Sofa Bed
Issue 314 | Volume 65| Number 4 |
August 2009
3/4 x 32-1/2 x 80" back panel
Inside panel is 3/4" narrower than outside, leaving 3/4 x 3/4" rabbet
R 1 ½”
R 3⁄8”
Armrest support 2 ea. side #8 x 2-1/2" FHWS
32 ½”
1-1/2 x 3 x 17" support cleat see section A-A for location #8 x 2-1/2" FHWS
80”
¾”
BACK PANEL
Outside panel
BASIC UNIT
43”
R 3⁄8”
¾”
¾”
Inside panel
42 ¼”
R 3⁄8”
R 3”
43”
5 1⁄8”
¾”
R ½”
1 ¼”
8”
9 ¼”
22”
4 3⁄8”
24”
4”
32”
3/4" hole, 1/2" deep located after final assembly
1 ¼”
R ¼”
¾”
19 ¾” ARM REST
¾”
R ¼”
2 ¾”
2” R ½”
1 ¼”
4 3⁄8”
2 ¾”
1 ¾”
1 ¾” 7” 3 ¼”
R 2”
R 3”
3 5⁄8”
4” R 4”
33 ½” 3”
3 ½” 6”
1 ½”
1 ½”
20 ½”
ARMREST SUPPORT
SECTION A-A
¾”
END PANEL
(left end panel shown)
2 of 4 ®
Sofa Bed
Issue 314 | Volume 65| Number 4 |
August 2009
K
16" full-extension drawer guide
O
24”
P 22 ½”
L
Q
P
R=1/4"
14 ½” 16”
K
L
#8 x 1-1/4" FHWS
A
O R
M
8”
DRAWER ASSEMBLY
M
A
3/4 x 12 x 25-3/4" plywood
SECTION A-A
Fabric cushion cover
DRAWER UNIT
¾”
DRAWER ¾”
¾” 5/32" hole countersunk
78 ½”
¾”
2 5⁄8”
22 ½”
¾”
1 ½”
16”
1” 3⁄8”
16”
8”
4 3⁄8” 4” 11 ¼”
DRAWER UNIT - FRONT VIEW 16”
¼”
¼” 25”
25”
9”
3⁄8”
1 5⁄8”
8”
8”
4” 2 5⁄8”
DRAWER FRONT/BACK
3” 3”
3⁄8”
DRAWER SIDE
25”
3 ½” R 3⁄8”
DRAWER UNIT - FRONT VIEW
R 3⁄8” 1 ½”
3 of 4 ®
Sofa Bed
Issue 314 | Volume 65| Number 4 |
August 2009
1 ¾”
R ¼” 2”
A
AA
4 ¾”
69 ½”
SECTION B-B DETAIL A
W
D V #8 X 2" FHWS
X Z
76”
4" surface bolt
#8 x 1-1/4" FHWS 1/2 X 4" carriage bolt
U
#8 X 2" FHWS
B
B
40”
Y W
#8 x 1-1/4" FHWS
41 ½”
6" lawnmower wheel 1/2" hole with 1" counterbore, 1/4" deep
DETAIL D
TOP VIEW 77 ½” ¾”
A
40” ¾”
7 ½”
4 ¾” 4”
WHEEL UNIT SIDE
R 1”
40”
SECTION A-A
R 1”
14 ¾”
2”
A FRONT VIEW - ROLL-OUT BED
4 of 4 ®
Sofa Bed
Issue 314 | Volume 65| Number 4 |
August 2009