Loading documents preview...
Customer Item number Service Flowserve reference Date
: : : : :
WIJAYA KARYA, PT. P 7A/B/C LPG FILLING PUMP 445564384 October 1, 2015
Pump size & type Based on curve no. Number of stages
: 4HPX13A : 4HPX13A-1-2 : 1
Capacity Head Specific gravity Pump speed Test tolerance
: : : : :
167.0 m3/h 91.18 m 0.510 2975 rpm API 610 11th Edition
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND POWER.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
1 of 20
Hydraulic Datasheet Customer Customer reference Item number Service
: : : :
WIJAYA KARYA, PT. PT WIKA P 7A/B/C LPG FILLING PUMP
Operating Conditions Capacity : 167.0 m³/h Water capacity (CQ=1.00) : Normal capacity : Total developed head : 91.18 m Water head (CH=1.00) : NPSH available (NPSHa) : 15.1 m NPSHa less NPSH margin : 14.1 m Maximum suction pressure : 18.0 kg/cm²g Liquid : Hydrocarbon : 35 °C / 0.510 : / 14.0 mm : 0.12 cP / 136.59 psia
Liquid type Temperature / Spec. Gravity Solid Size - Actual / Limit Viscosity / Vapor pressure Hydraulic power Pump speed Pump overall efficiency (CE=1.00)
: 21.1 kW : 2975 rpm : 69.4 %
NPSH required (NPSH3) Rated power Maximum power Driver power Casing working pressure (based on shut off @ cut dia/rated SG) Maximum allowable Hydrostatic test pressure Est. rated seal chamb. press.
: : : : :
4.3 m 30.4 kW 38.0 kW 37.0 kW / 49.6 hp 23.2 kg/cm²g
: 42.2 kg/cm²g : 63.3 kg/cm²g : 0.9 kg/cm²g
Pump / Stages Based on curve no. Flowserve reference Date
: : : :
4HPX13A 4HPX13A-1-2 445564384 October 1, 2015
Material column code Pump specification
Materials / Specification : S-8 : -
/1
Other Requirements Hydraulic selection : API 610 11th Edition Construction : API 610 11th Edition Test tolerance : API 610 11th Edition Max NSS : 11000.0 (US units) Min NPSHa Margin : 1.0 m Driver Sizing : API 610 Performance data based on standard impeller Seal configuration : Single Seal
Performance Impeller diameter Rated Maximum Minimum Suction specific speed Minimum continuous flow Maximum head @ rated dia Flow at BEP Flow as % of BEP Efficiency at normal flow Impeller dia ratio (rated/max) Head rise to shut off Total head ratio (rated/max)
: : : : : : : : : : : :
266.9 mm 323.8 mm 254.0 mm 9370 (US units) 76.7 m³/h 102.24 m 197.1 m³/h 84.7 % 82.4 % 12.1 % 64.5 %
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND POWER.
** denotes rejection criteria
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
2 of 20
Full Page GA Drawing
All dimensions are in millimeters unless otherwise specified Customer Item number
: WIJAYA KARYA, PT. : P 7A/B/C
Pump size & type Pump speed / Stages
: 4HPX13A : 2975 rpm / 1
Service Customer PO # Flowserve reference
: LPG FILLING PUMP : : 445564384
Flow / Head Driver power / Frame Volts / Phase / Hz
: 167.0 m3/h / 91.18 m : 37.0 kW / 49.6 hp / 200L : - / - / 50
Copyright © 2014 Flowserve. All rights reserved.
Drawing number Date Certified by / Date :
: : October 1, 2015 : -
Seal type Seal flush plan
: : Plan 11 Affinity v1.3.9.1
4 of 20
Customer Item number Service Flowserve reference Date
: : : : :
WIJAYA KARYA, PT. P-30 DEP WELL PUMP 445564384 October 2, 2015
Pump size & type Based on curve no. Number of stages
: 2K2x1.5V-10ARV M3V : MIII8021AV : 1
Capacity Head Specific gravity Pump speed Test tolerance
: : : : :
20.0 m3/h 49.41 m 1.000 2900 rpm Hydraulic Institute Level B
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
5 of 20
Hydraulic Datasheet Customer Customer reference Item number Service
: : : :
WIJAYA KARYA, PT. PT WIKA P-30 DEP WELL PUMP
Operating Conditions Capacity : 20.0 m³/h Water capacity (CQ=1.00) : Normal capacity : Total developed head : 49.41 m Water head (CH=1.00) : NPSH available (NPSHa) : Ample NPSHa less NPSH margin : Maximum suction pressure : 0.0 kg/cm²g Liquid : Other : 55 °C : : 1.00 cP
Liquid type Temperature / Spec. Gravity Solid Size - Actual / Limit Viscosity / Vapor pressure
Pump / Stages Based on curve no. Flowserve reference Date Material column code Pump specification
: : : :
2K2x1.5V-10ARV M3V MIII8021AV 445564384 October 2, 2015
/1
Materials / Specification : DS : ANSI B73.2M
Other Requirements Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level B Driver Sizing : API 610 Seal configuration : Single Seal
/ 1.000 //-
Hydraulic power Pump speed Pump overall efficiency (CE=1.00)
: 2.69 kW : 2900 rpm : 42.1 %
NPSH required (NPSH3) Rated power Maximum power Driver power Casing working pressure (based on shut off @ cut dia/rated SG) Maximum allowable Hydrostatic test pressure Est. rated seal chamb. press.
: : : : :
1.7 m 6.39 kW 7.44 kW 11.2 kW / 15.0 hp 5.9 kg/cm²g
: 19.5 kg/cm²g : 30.1 kg/cm²g : -
Performance Impeller diameter Rated Maximum Minimum Suction specific speed Minimum continuous flow Maximum head @ rated dia Flow at BEP Flow as % of BEP Efficiency at normal flow Impeller dia ratio (rated/max) Head rise to shut off Total head ratio (rated/max)
: : : : : : : : : : : :
201.6 mm 254.0 mm 152.4 mm 5660 (US units) 2.4 m³/h 59.08 m 21.2 m³/h 94.3 % 79.4 % 19.6 % 55.2 %
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
6 of 20
Full Page GA Drawing
All dimensions are in millimeters unless otherwise specified Customer Item number
: WIJAYA KARYA, PT. : P-30
Pump size & type Pump speed / Stages
: 2K2x1.5V-10ARV M3V : 2900 rpm / 1
Service Customer PO # Flowserve reference
: DEP WELL PUMP : : 445564384
Flow / Head Driver power / Frame Volts / Phase / Hz
: 20.0 m3/h / 49.41 m : 11.2 kW / 15.0 hp / 254TC : 400 / 3 / 50
Copyright © 2014 Flowserve. All rights reserved.
Drawing number Date Certified by / Date :
: : October 2, 2015 : -
Seal type Seal flush plan
: ISC2 Pusher : F - API Plan 13 Affinity v1.3.9.1
8 of 20
Customer Item number Service Flowserve reference Date
: : : : :
WIJAYA KARYA, PT. P-29 WATER PIT PUMP 445564384 October 2, 2015
Pump size & type Based on curve no. Number of stages
: 1K3x1.5V-81RV M3V : MIII7168 : 1
Capacity Head Specific gravity Pump speed Test tolerance
: : : : :
30.0 m3/h 42.45 m 1.000 2900 rpm Hydraulic Institute Level B
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
9 of 20
Hydraulic Datasheet Customer Customer reference Item number Service
: : : :
WIJAYA KARYA, PT. PT WIKA P-29 WATER PIT PUMP
Operating Conditions Capacity : 30.0 m³/h Water capacity (CQ=1.00) : Normal capacity : Total developed head : 42.45 m Water head (CH=1.00) : NPSH available (NPSHa) : Ample NPSHa less NPSH margin : Maximum suction pressure : 0.0 kg/cm²g Liquid : Other : 55 °C : : 1.00 cP
Liquid type Temperature / Spec. Gravity Solid Size - Actual / Limit Viscosity / Vapor pressure
Pump / Stages Based on curve no. Flowserve reference Date Material column code Pump specification
: : : :
1K3x1.5V-81RV M3V MIII7168 445564384 October 2, 2015
/1
Materials / Specification : DS : ANSI B73.2M
Other Requirements Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level B Driver Sizing : API 610 Seal configuration : Single Seal
/ 1.000 //-
Hydraulic power Pump speed Pump overall efficiency (CE=1.00)
: 3.46 kW : 2900 rpm : 57.2 %
NPSH required (NPSH3) Rated power Maximum power Driver power Casing working pressure (based on shut off @ cut dia/rated SG) Maximum allowable Hydrostatic test pressure Est. rated seal chamb. press.
: : : : :
1.8 m 6.05 kW 7.72 kW 11.2 kW / 15.0 hp 4.6 kg/cm²g
: 19.5 kg/cm²g : 30.1 kg/cm²g : -
Performance Impeller diameter Rated Maximum Minimum Suction specific speed Minimum continuous flow Maximum head @ rated dia Flow at BEP Flow as % of BEP Efficiency at normal flow Impeller dia ratio (rated/max) Head rise to shut off Total head ratio (rated/max)
: : : : : : : : : : : :
188.9 mm 204.8 mm 101.6 mm 7680 (US units) 3.9 m³/h 45.75 m 37.9 m³/h 79.1 % 92.2 % 7.8 % 80.7 %
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
10 of 20
Full Page GA Drawing
All dimensions are in millimeters unless otherwise specified Customer Item number
: WIJAYA KARYA, PT. : P-29
Pump size & type Pump speed / Stages
: 1K3x1.5V-81RV M3V : 2900 rpm / 1
Service Customer PO # Flowserve reference
: WATER PIT PUMP : : 445564384
Flow / Head Driver power / Frame Volts / Phase / Hz
: 30.0 m3/h / 42.45 m : 11.2 kW / 15.0 hp / 254TC : 400 / 3 / 50
Copyright © 2014 Flowserve. All rights reserved.
Drawing number Date Certified by / Date :
: : October 2, 2015 : -
Seal type Seal flush plan
: ISC2 Pusher : F - API Plan 13 Affinity v1.3.9.1
12 of 20
Customer Item number Service Flowserve reference Date
: : : : :
WIJAYA KARYA, PT. P-28 A/B SEA WATER INTAKE P... 445564384 October 2, 2015
Pump size & type Based on curve no. Number of stages
: 12EHM : EC-2657 : 2
Capacity Head Specific gravity Pump speed Test tolerance
: : : : :
570.0 m3/h 76.68 m 1.000 2950 rpm Hydraulic Institute Level A
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 77.81 m corresponds with 76.68 m head at discharge flange adjusted for elevation and friction losses.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
13 of 20
Hydraulic Datasheet Customer Customer reference Item number Service
: : : :
WIJAYA KARYA, PT. PT WIKA P-28 A/B SEA WATER INTAKE PUMP
Pump / Stages Based on curve no. Flowserve reference Date
Operating Conditions Capacity Water capacity (CQ=1.00) Normal capacity Total developed head Water head (CH=1.00) NPSH available (NPSHa) NPSHa less NPSH margin Maximum suction pressure Rated suction pressure
: : : : : : : : :
: : : :
12EHM EC-2657 445564384 October 2, 2015
/2
Materials / Specification
570.0 m³/h 76.68 m Ample Not applicable Not applicable
Material column code
: B30 Other Requirements
Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level A Driver Sizing : API 610
Liquid Liquid type Liquid description Temperature / Spec. Gravity Viscosity / Vapor pressure
: : : :
Other WATER 55 °C 1.00 cP
Pump speed NPSH required (NPSH3) Minimum submergence Hydraulic power Pump overall efficiency (CE=1.00) Power: (Rated / Max) Driver power Bowl Pressure (based on shut off @ cut dia/rated SG) Maximum allowable Bowl & column hydrotest Dischg Head Dischg Region MAWP Suction specific speed
: : : : : : : :
2950 rpm 13.2 m 609.6 mm 120 kW 77.6 % 155 kW / 155 kW 185 kW / 248 hp 13.3 kg/cm²g
: : : :
30.2 kg/cm²g 16.6 kg/cm²g 20.0 kg/cm²g 9240 (US units)
/ 1.000 / Performance Impeller diameter
: Rated / Maximum / Minimum : 229.1 mm 237.0 mm 214.4 mm Impeller dia ratio (rated/max) : 96.7 % Maximum head @ rated dia : 133.20 m Head rise to shut off : 71.2 % Total head ratio (rated/max) : 82.7 % Flow at BEP : 492.7 m³/h Flow as % of BEP : 115.7 % Minimum continuous flow : 198.0 m³/h Rated thrust (at Rated flow) : 8800.6 N Maximum thrust (at Shut off flow) : 14846.7 N Min thrust - Runout flow / Max Suction : 6474.1 N (A negative thrust value indicates an upthrust condition)
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY. Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 77.81 m corresponds with 76.68 m head at discharge flange adjusted for elevation and friction losses.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
14 of 20
Full Page GA Drawing
All dimensions are in millimeters unless otherwise specified Customer Item number
: WIJAYA KARYA, PT. : P-28 A/B
Pump size & type Pump speed / Stages
: 12EHM : 2950 rpm / 2
Service Customer PO # Flowserve reference
: SEA WATER INTAKE PUMP : : 445564384
Flow / Head Driver power / Frame Volts / Phase / Hz
: 570.0 m3/h / 76.68 m : 185 kW / 248 hp / : 400 / 0 / 50
Copyright © 2014 Flowserve. All rights reserved.
Drawing number Date Certified by / Date :
: : October 2, 2015 : -
Seal type Seal flush plan
: Packing : Plan 13 Affinity v1.3.9.1
16 of 20
Customer Item number Service Flowserve reference Date
: : : : :
WIJAYA KARYA, PT. P-26 JOCKEY PUMP 445564384 October 2, 2015
Pump size & type Based on curve no. Number of stages
: 2K3x1.5LF-13 M3 LF : MIII7306V : 1
Capacity Head Specific gravity Pump speed Test tolerance
: : : : :
12.0 m3/h 106.52 m 1.000 2900 rpm Hydraulic Institute Level B
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY. MCSF PROVIDES MECHANICAL PROTECTION ONLY. MINIMUM THERMAL FLOW MUST BE CALCULATED FOR THE SPECIFIC FLUID AND OPERATING CONDITIONS.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
17 of 20
Hydraulic Datasheet Customer Customer reference Item number Service
: : : :
WIJAYA KARYA, PT. PT WIKA P-26 JOCKEY PUMP
Operating Conditions Capacity : 12.0 m³/h Water capacity (CQ=1.00) : Normal capacity : Total developed head : 106.52 m Water head (CH=1.00) : NPSH available (NPSHa) : 7.9 m NPSHa less NPSH margin : Maximum suction pressure : 0.0 kg/cm²g Liquid type Temperature / Spec. Gravity Solid Size - Actual / Limit Viscosity / Vapor pressure
Pump / Stages Based on curve no. Flowserve reference Date
: : : :
2K3x1.5LF-13 M3 LF MIII7306V 445564384 October 2, 2015
Material column code Pump specification
Materials / Specification : DCI : ANSI B73.1
/1
Other Requirements Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level B Driver Sizing : API 610 Seal configuration : Single Seal
Liquid : Hydrocarbon : 35 °C / 1.000 : / 8.0 mm : 0.78 cP / 0.57 psia
Hydraulic power Pump speed Pump overall efficiency (CE=1.00)
: 3.48 kW : 2900 rpm : 21.6 %
NPSH required (NPSH3) Rated power Maximum power Driver power Casing working pressure (based on shut off @ cut dia/rated SG) Maximum allowable Hydrostatic test pressure Est. rated seal chamb. press.
: : : : :
0.9 m 16.1 kW 23.0 kW 22.4 kW / 30.0 hp 10.8 kg/cm²g
: 17.6 kg/cm²g : 26.4 kg/cm²g : -
Performance Impeller diameter Rated Maximum Minimum Suction specific speed Minimum continuous flow Maximum head @ rated dia Flow at BEP Flow as % of BEP Efficiency at normal flow Impeller dia ratio (rated/max) Head rise to shut off Total head ratio (rated/max)
: : : : : : : : : : : :
247.6 mm 330.2 mm 228.6 mm 7890 (US units) 0.0 m³/h 108.47 m 29.7 m³/h 40.4 % 75.0 % 1.8 % 53.3 %
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY. MCSF PROVIDES MECHANICAL PROTECTION ONLY. MINIMUM THERMAL FLOW MUST BE CALCULATED FOR THE SPECIFIC FLUID AND OPERATING CONDITIONS.
Copyright © 2014 Flowserve. All rights reserved.
Affinity v1.3.9.1
18 of 20
Full Page GA Drawing
All dimensions are in millimeters unless otherwise specified Customer Item number
: WIJAYA KARYA, PT. : P-26
Pump size & type Pump speed / Stages
: 2K3x1.5LF-13 M3 LF : 2900 rpm / 1
Service Customer PO # Flowserve reference
: JOCKEY PUMP : : 445564384
Flow / Head Driver power / Frame Volts / Phase / Hz
: 12.0 m3/h / 106.52 m : 22.4 kW / 30.0 hp / 286TS : - / 3 / 50
Copyright © 2014 Flowserve. All rights reserved.
Drawing number Date Certified by / Date :
: : October 2, 2015 : -
Seal type Seal flush plan
: ISC2 Pusher : D - Plan 11 Affinity v1.3.9.1
20 of 20