SEC-- CMC Training SEC
Mohammad AlAl-Fayoumi Technical Support and Application Engineer
[email protected] mohammad.al
© OMICRON
Page: 1
CMC Training Please: • Ask your questions immadiately during the presentation • Training Manuals are available • All Breaks will be decided during the presentation
and finally • Please Switch-Off Mobile Phones!!!
© OMICRON
Page: 2
What Do We Have ?
CMC356 - The Front … © OMICRON
Page: 3
CMC356 - The Back …
© OMICRON
Page: 4
Test Universe – Start Page © OMICRON
Page: 5
Test Universe – Start Page
© OMICRON
Page: 6
Test Universe – Setup
© OMICRON
Page: 7
Setup – License Manager 1. Select drive storing omicron.lic file on CD ROM. (file can also be copied to USB stick) 2. Press SEARCH. Software automatically finds the omicron.lic file on drive. 3. Highlight file in window. 4. Press to Merge File Into Master License File
© OMICRON
Page: 8
Setup – System Settings TABS of interest 1. User Information 2. Phase Names 3. Default Values
© OMICRON
Page: 9
Setup - Association
© OMICRON
Page: 10
Getting Started - Support
© OMICRON
Page: 11
Technical Support Booklet…
© OMICRON
Page: 12
Where to find Booklet…
Booklet will slot inside the softbag © OMICRON
Page: 13
Connection Method © OMICRON
Page: 14
Detection & Connection for Testing
I> I>
IN> I>
for Single Phase OC Relay © OMICRON
Page: 15
I> IN>
Fault Type C-N Fault Type A-B Fault Type 3 Phase
for Three Phase OC Relay © OMICRON
Page: 16
OHM Principle © OMICRON
Page: 17
What is the OHM Principle
© OMICRON
Page: 18
For electromechanical relays set to LOW © OMICRON
Page: 19
© OMICRON
Page: 20
© OMICRON
Page: 21
Aux DC © OMICRON
Page: 22
Aux DC Settings Set your desired value and click SET Never set your value to Default ! Check connection be confirming you see your CMC and Serial No: xxxxxx
Examples of where to use: Use Aux DC if you require to operate a relay Use if you want a binary output to switch to a DC value
© OMICRON
Page: 23
QuickCMC - Manual Control © OMICRON
Page: 24
© OMICRON
Page: 25
Create Test Values
© OMICRON
Page: 26
QuickCMC – Set Modes
© OMICRON
Page: 27
QuickCMC Testing Control
© OMICRON
Page: 28
QuickCMC INPUTS & OUTPUTS
RED indicator shows relay contacts closed
© OMICRON
Page: 29
QuickCMC – Unit Manager
© OMICRON
Page: 30
QuickCMC – Ramping
© OMICRON
Page: 31
QuickCMC – Ramping
© OMICRON
Page: 32
QuickCMC – Pulse Ramping
© OMICRON
Page: 33
QuickCMC – Reporting
© OMICRON
Page: 34
QuickCMC Summary QuickCMC is used for quick, direct control • Troubleshooting • Wiring Check • Powerful ramping and state control • Choice of units and output values Tends not to be used for reporting or with Test Object / Hardware configured Often used as a preliminary check before employing an advanced module
© OMICRON
Page: 35
Ramping & State Sequencer © OMICRON
Page: 36
© OMICRON
Page: 37
Ramping Test Values
© OMICRON
Page: 38
Trigger & Signal View
© OMICRON
Page: 39
Starting & Controlling Test
© OMICRON
Page: 40
State Sequencer
© OMICRON
Page: 41
State Sequencer Easy and Intuitive Tool to Test Complex Functions
© OMICRON
Page: 42
State Sequencer Add & Remove States
© OMICRON
Page: 43
State Sequencer Various trigger functions
Measurements View
© OMICRON
Page: 44
Time Signal View
© OMICRON
Page: 45
Ramping/State Sequencer Summary Ramping • Generates ramps of Amplitude, Phase, and Frequency • Automated testing for Pick Up and Drop Of values • Simultaneous ramps for 2 independent variables • Automatic Results Assessment State Sequencer • Determine operating times and logic • Chain States together to complete a test sequence • Ideal for CB Fail, TCS, SOFT • Automatic Results Assessment
© OMICRON
Page: 46
Overcurrent © OMICRON
Page: 47
© OMICRON
Page: 48
Overcurrent Relay Testing
© OMICRON
Page: 49
Define Test Device & Characteristic
© OMICRON
Page: 50
Overcurrent Test Values
© OMICRON
Page: 51
Overcurrent Directional Test
© OMICRON
Page: 52
© OMICRON
Page: 53
Overcurrent Summary Overcurrent is one of the specific modules • Tests the characteristic (not just overcurrent!) • Pickup test (with or without contact) • Directional testing available Used for reporting with Test Object / Hardware configured
© OMICRON
Page: 54
Distance Protection
© OMICRON
Page: 55
© OMICRON
Page: 56
© OMICRON
Page: 57
© OMICRON
Page: 58
© OMICRON
Page: 59
© OMICRON
Page: 60
© OMICRON
Page: 61
© OMICRON
Page: 62
© OMICRON
Page: 63
© OMICRON
Page: 64
© OMICRON
Page: 65
© OMICRON
Page: 66
Differential Protection
© OMICRON
Page: 67
© OMICRON
Page: 68
© OMICRON
Page: 69
© OMICRON
Page: 70
© OMICRON
Page: 71
© OMICRON
Page: 72
© OMICRON
Page: 73
© OMICRON
Page: 74
© OMICRON
Page: 75
© OMICRON
Page: 76
Omicron Control Center xxx.OCC Files © OMICRON
Page: 77
OCC Test Plan Structure
© OMICRON
Page: 78
Starting Automated Testing
© OMICRON
Page: 79
Locate file & OPEN
After the test, all results are in one report.
© OMICRON
Page: 80
Example of a Report Graphics and Drawings Word-process text, Headers and Footers Automated Fields Configurable to show: • Test Detail • Graphs • Results • Summary Dates / Times Export to .RTF
© OMICRON
Page: 81
Create New Test Plan OCC Files
• Test object data • Hardware configuration • Test modules in one Test plan (OMICRON Control Center Document). The helper modules • Pause
© OMICRON
Page: 82
OMICRON Control Center Summary • • • • •
Embedded Test Modules for automated testing All Functions of Test Object tested with ONE test plan Re-Usability – create templates Automatic Results Assessment & Graphics Link-to-XRIO technology
© OMICRON
Page: 83